Texas Instruments TUSB1044 User manual

1
SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
TUSB1044 Active Cable EVM
User's Guide
SLLU265B–March 2018–Revised August 2018
TUSB1044 Active Cable EVM
The TUSB1044 device is a Video Electronics Standards Association (VESA®) USB Type-C™ Alternate
Mode (Alt Mode) re-driving switch supporting data rates up to 10Gbps for a downstream facing port (Host)
or upstream facing port (Device). This guide describes how to bring up the EVM and includes schematics
that can be used as reference for the cable implementations with the TUSB1044 device. This EVM is
intended to demonstrate the SuperSpeed and SuperSpeed+ functionality of the TUSB1044.
Contents
1 TUSB1044EVM .............................................................................................................. 2
2 TUSB1044EVM Configuration ............................................................................................. 3
3 TUSB1044EVM Schematics ............................................................................................... 7
4 Bill of Materials ............................................................................................................. 11
List of Figures
1 TUSB1044 EVM ............................................................................................................. 2
2 TUSB1044 System Example............................................................................................... 2
3 Early Board JMP10 and JMP12 Schematic.............................................................................. 3
4 Early Board JMP10 and JMP12 Layout .................................................................................. 4
5 TUSB1044EVM Schematic (Page 1)...................................................................................... 7
6 TUSB1044EVM Schematic (Page 2)...................................................................................... 8
7 TUSB1044EVM Schematic (Page 3)...................................................................................... 9
8 TUSB1044EVM Schematic (Page 4) .................................................................................... 10
List of Tables
1 TUSB1044 Configuration Pins ............................................................................................. 3
2 Switch Configuration ........................................................................................................ 4
3 Config Pin-Level Definitions................................................................................................ 5
4 USB 3.1 EQ Settings........................................................................................................ 5
5 VOD Linear Range and DC Gain.......................................................................................... 6
6 TUSB1044 Bill of Materials ............................................................................................... 11
Trademarks
USB Type-C is a trademark of USB Implementer's Forum.
DisplayPort is a trademark of Video Electronics Standards Association.
VESA is a registered trademark of Video Electronics Standards Association.
All other trademarks are the property of their respective owners.

USB/DP
Source
USB Type-C USB Type-C USB Type-C Device /
Dock / Dongle
TUSB1044EVM
TUSB1044EVM www.ti.com
2SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
TUSB1044 Active Cable EVM
1 TUSB1044EVM
Figure 1 illustrates the TUSB1044 Active Cable EVM.
Figure 1. TUSB1044 EVM
The TUSB1044EVM can be used with a DFP or UFP USB Type-C source or device to evaluate the USB
Type-C implementation. Figure 2 is a typical test set-up.
Figure 2. TUSB1044 System Example

www.ti.com TUSB1044EVM Configuration
3
SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
TUSB1044 Active Cable EVM
2 TUSB1044EVM Configuration
This section provides the configuration options available in the TUSB1044EVM.
2.1 TUSB1044 EVM Default Jumper and Switch Configuration
The following headers are provided for TUSB1044 configuration by default, configuration settings may
need to be optimized depending on the amount of loss of each channel in the system.
Table 1. TUSB1044 Configuration Pins
Reference
Designator JMP Control Configuration
J1 CTL0/SDA No Connect
J2 FLIP/SCL No Connect
J3 HPDIN No Connect
J4 VCC Isolate No Connect
JMP2 DEQ1 SHUNT on pin 1-2 (GND)
JMP3 DEQ0 SHUNT on pin 1-2 (GND)
JMP4 UEQ1/A1 SHUNT on pin 1-2 (GND)
JMP5 UEQ0/A0 SHUNT on pin 1-2 (GND)
JMP6 CFG1 SHUNT on pin 2–4 (20K PD)
JMP7 CFG0 SHUNT on pin 1-2 (GND)
JMP8 VIO_SEL SHUNT on pin 1-2 (GND)
JMP9 I2C_EN SHUNT on pin 1-2 (GND)
JMP10 EQ1 SHUNT on pin 1-2 (200 Ωto GND)
JMP11 DC_BOOST1 SHUNT on pin 1-2 (20 kΩto 3.3 V)
JMP12 EQ2 SHUNT on pin 1-2 (200 Ωto GND)
JMP13 DC_BOOST2 SHUNT on pin 1-2 (20 kΩto 3.3 V)
NOTE: Figure 3 and Figure 4 show how some early boards were built with a different configuration
of JMP10 and JMP12. For these boards, connect a jumper wire from pin 1 to pins 3–5.
Figure 3. Early Board JMP10 and JMP12 Schematic

TUSB1044EVM Configuration www.ti.com
4SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
TUSB1044 Active Cable EVM
Figure 4. Early Board JMP10 and JMP12 Layout
Table 2. Switch Configuration
SW1 Position Control Signal Configuration
1 EN ON
2 SWAP OFF
3 SLP_S0# ON
4 DIR1 OFF
5 DIR0 OFF
6 CTL1 ON
7 CTL0/SDA ON
8 FLIP/SCL OFF

www.ti.com TUSB1044EVM Configuration
5
SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
TUSB1044 Active Cable EVM
2.2 TUSB1044 EQ Control
Each of the TUSB1044 receiver lanes has individual controls for receiver equalization. Table 3 through
Table 5 detail the gain values for each available combination for downstream, upstream, and all
DisplayPort™ configurations.
Table 3. Config Pin-Level Definitions
Level Settings
0 Option 1: Tie 1 kΩ, 5% to GND
Option 2: Tie directly to GND
R Tie 20 kΩ, 5% to GND
F Float (leave pin open)
1 Option 1: Tie 1 kΩ, 5% to VCC
Option 2: Tie directly to VCC
Table 4. USB 3.1 EQ Settings
USB 3.1 Downstream Facing Ports USB 3.1 Upstream Facing Ports
DEQ1 Pin Level DEQ0 Pin Level EQ Gain at 5 GHz
(dB) UEQ1 Pin Level UEQ0 Pin Level EQ Gain at 5 GHz (dB)
0 0 0 0 0 0
0 R 1 0 R 1
0 F 2 0 F 2
0 1 3 0 1 3
R 0 4 R 0 4
R R 5 R R 5
R F 6 R F 6
R 1 7 R 1 7
F 0 8 F 0 8
F R 9 F R 9
F F 10 F F 10
F 1 11 F 1 11
1 0 12 1 0 12
1 R 13 1 R 13
1 F 14 1 F 14
1 1 15 1 1 15

TUSB1044EVM Configuration www.ti.com
6SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
TUSB1044 Active Cable EVM
Table 5. VOD Linear Range and DC Gain
VOD Linear Range and DC Gain
Setting CFG1 Pin Level CFG0 Pin Level DS DC Gain (dB) US DC Gain (dB) DS VOD (mVpp) US VOD (mVpp)
1 0 0 [phone]
2 0 R 0 +1 900 900
3 0 F 0 0 900 900
4 0 1 +1 +1 900 900
5 R 0 0 0 1100 1100
6 R R [phone]
7 R F 0 [phone]
8 R 1 +2 [phone]
9 F 0 –1 –1 1300 1300
10 F R +2.5 +2.5 1300 1300
11 F F 0 0 1300 1300
12 F 1 +1 [phone]
13 1 0 –1 0 1300 1300
14 1 R 0 –1 1300 1300
15 1 F 0 [phone]
16 1 1 [phone]
2.3 Power
The EVM is designed to operate off of the VBUS from a USB host connected via the USB Type-C plug
connector. Apply no external power via J4, unless standalone operation is desired.
If testing DisplayPort only, or if bypassing VBUS power, the EVM must be powered via J4 (5 V, 1-A input).

Type-C Plug
Type-C Receptacle
I2C_EN
VIO_SEL
DIR0
SLP_S0#
CFG1
CFG0
UEQ1/A1
FLIP/SCL
CTL0/SDA
CTL1
DEQ1
HPDIN
UEQ0/A0
DEQ0
DC_BOOST1
EQ1
SWAP
DIR1
CFG1
DC_BOOST2
EQ2
VBUS VBUS
VBUS
1044_VCC
1044_VCC
1044_VCC
1044_VCC
1044_VCC
1044_VCC
1044_VCC
C30 DNI - 0.1uF
R63 0
C5 220nF
R70 DNI - 0
D5
Green
C32
0.1uF
C27
0.1uF
R43 DNI - 0
U5
TPD4E02B04
IO1
1
IO2
2
GND1
3
IO3
4
IO4
5NC4 6
NC3 7
GND2 8
NC2 9
NC1 10
C6 220nF
C19
1uF
R71 0
C14 220nF
C11 220nF
C31 DNI - 0.1uF
C1 220nF
D4
Green
R65 0
R67
75
C9 220nF
C22
0.1uF
R54 DNI - 0
R64 0
C7 220nF
C23
0.1uF
U1
TUSB1044
VCC 1
DPEQ1 2
SSEQ1 3
SSRXn 4 SSRXp 5
VCC 6
SSTXn 7 SSTXp 8
DP0p
9
DP0n
10
SSEQ0/A0
11
DP1p
12
DP1n
13
DPEQ0/A1
14
DP2p
15
DP2n
16
I2C_EN
17
DP3p
18
DP3n
19
VCC
20
FLIP/SCL
21
CTL0/SDA
22
CTL1/HPDIN
23
AUXp
24
AUXn
25
SBU2
26
SBU1
27
VCC
28
CAD_SNK 29
RX1p 30
RX1n 31
HPDIN 32
TX1p 33
TX1n 34
EQ1 35
TX2n 36
TX2p 37
EQ0 38
RX2n 39
RX2p 40
PAD/GND 41
R72 0
C33
0.1uF
R44 DNI - 0
R66 DNI - 0
C10 220nF
U3
TPD6S300
VPWR
10
VBIAS
3
CC1
12
CC2
11
SBU1
15
SBU2
14
D1
20
D2
19
D3
17
D4
16
FLT 9
RPD_G1 7
RPD_G2 6
C_CC1 4
C_CC2 5
C_SBU1 1
C_SBU2 2
GND1 8
GND2 13
GND3 18
PAD 21
R1 DNI
C8 220nF
U7
TUSB212
EQ
1
NC1 2 NC2 3
ENA_HS 4
D2P 5
D2M 6
GND 7
VREG 8
D1M
9D1P
10 SDA 11 VCC 12 SCL 13
RSTN
14
PAD 15
R53 DNI - 0
C2 220nF
R68
75
C15 220nF
R62 0
R2 DNI
D3
Green
C29
0.1uF
C12 220nF
P2
JAE DX07S024JJ2
GND1
A1
SSTXP1
A2
SSTXN1
A3
VBUS1
A4
CC1
A5
DP1
A6 DN1
A7
SBU1
A8
VBUS2
A9
SSRXN2
A10 SSRXP2
A11
GND2
A12
GND3
B1
SSTXP2
B2
SSTXN2
B3
VBUS3
B4
CC2
B5
DP2
B6
DN2
B7
SBU2
B8
VBUS4
B9
SSRXN1
B10 SSRXP1
B11
GND4
B12
CHASSIS1 1
CHASSIS2 2
CHASSIS3 3
CHASSIS4 4
CHASSIS5 5
CHASSIS6 6
C3 220nF
C16 220nF
C18
1uF
R61 0
U4
TPD4E02B04
IO1
1
IO2
2
GND1
3
IO3
4
IO4
5NC4 6
NC3 7
GND2 8
NC2 9
NC1 10
C4 220nF
C28
0.1uF
C20
1uF
C21
0.1uF
R69 DNI - 0
C13 220nF
U6
TUSB212
EQ
1
NC1 2 NC2 3
ENA_HS 4
D2P 5
D2M 6
GND 7
VREG 8
D1M
9D1P
10 SDA 11 VCC 12 SCL 13
RSTN
14
PAD 15
R73
75
R42 100K
C17
10uF
P1 Wurth 632712000021
GND
A1
SSTXp1
A2
SSTXn1
A3
VBUS
A4
CC1
A5
DP1
A6
DN1
A7
SBU1
A8
VBUS
A9
SSRXn2
A10
SSRXp2
A11
GND
A12 GND B1
SSTXp2 B2
SSTXn2 B3
VBUS B4
CC2 B5
SBU2 B8
VBUS B9
SSRXn1 B10
SSRXp1 B11
GND B12
GND
C1
GND
C2
GND
C3
GND
C4
DP2 B6
DN2 B7
CC1
CC2
UDP1
UDM1
C_CC1
C_CC2
AUXP
AUXN
AUXP
AUXN
URX2p
URX2n
UTX1n
UTX1p URX1p
URX1n
UTX2n
UTX2p
C_SBU1
C_SBU2
DTX1p
DTX1n
DRX2p
DRX2n
DTX2p
DTX2n
DRX1p
DRX1n
C_DRX2p
C_DRX2n
C_DTX2p
C_DTX2n
C_DTX1n
C_DTX1p
C_DRX1n
C_DRX1p
SBU2
SBU1
DRX2p
DRX2n
DTX2p
DTX2n
DTX1n
DTX1p
DRX1n
DRX1p
CC1
CC2
SBU1
SBU2
C_CC1
C_CC2
C_SBU1
C_SBU2
DDM1
DDP1
DTX1nDTX1n
DTX1p DTX1p
DRX1n
DRX1p
DRX1n
DRX1p
DTX2n
DTX2p
DRX2n
DRX2p
DTX2n
DTX2p
DRX2n
DRX2p
URX2p
URX2n
UTX2p
UTX2n
UTX1n
UTX1p
URX1n
URX1p
DDP1
DDM1
UDM1
UDP1
AUXP
AUXN
SBU1
SBU2
DIR0_URX1p
URX1p
URX1n
SLP_URX1n
UTX1p
SWAP_UTX1p
UTX1n
CFG1_UTX1n
CD1
CD1
FLIP/SCL
DDM2
DDM2
DDP2
UDP2
UDM2
DDP2
DDM1
DDP1
CD2
DDP2
DDM2
UDM2
UDP2
CD2
www.ti.com TUSB1044EVM Schematics
7
SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
TUSB1044 Active Cable EVM
3 TUSB1044EVM Schematics
Figure 5 through Figure 8 illustrate the EVM schematics.
Figure 5. TUSB1044EVM Schematic (Page 1)

SW1:
1 - EN
2 - SWAP
3 - SLP_S0#
4 - DIR1
5 - DIR0
6 - CTL1
7 - CTL0/SDA
8 - FLIP/SCL
SW1:
OFF = PD
ON = PU
JMP Configuration
2-1 = 0
2-3 = 1
2-4 = R
2 - NC = F
JMP1/JMP3 = DS Port EQ
JMP2/JMP4 = US Port EQ
JMP9/JMP8 = VOD / DC Gain
HPDIN
SHUNT = 3.3V
I2C
J2 - 2 = SDA
J3 - 2 = SCL
12
3
4
5
Note:
JMP10 and JMP12 pin configuration has changed
on later boards. See connector pin diagram and
layout below.
See Hardware Page for assembly notes.
EN
SWAP
SLP_S0#
DIR1
DIR0
CTL1
CTL0/SDA
FLIP/SCL
DEQ1
UEQ1/A1
DEQ0
UEQ0/A0
VIO_SEL
I2C_EN
CFG0
HPDIN
CFG1
CTL0/SDA
FLIP/SCL
DC_BOOST1
DC_BOOST2 EQ1 EQ2
1044_VCC
1044_VCC
1044_VCC
1044_VCC
1044_VCC
1044_VCC
1044_VCC
1044_VCC
1044_VCC
1044_VCC
1044_VCC
1044_VCC
1044_VCC33
R30 1K
JMP6
4 Pin-T Berg Jumper
1
2
3
4
JMP11
4 Pin-T Berg Jumper
1
2
3
4
JMP8
4 Pin-T Berg Jumper
1
2
3
4
R48 6.2K
R46 1.5K
R28 20K
JMP9
4 Pin-T Berg Jumper
1
2
3
4
R25 1K
R60 3.9K
R57 20K
R18
100K
R10
1K
R58 20K
R34 20K
R29 1K
JMP4
4 Pin-T Berg Jumper
1
2
3
4
R17
100K
R9
1K
R50 20K
R33 1K
R16
100K
R47 3.9K
R75 1.5K
R45 200
R15
100K
BERG1X2J1
R8
1K
R49 20K
R37 20K
R14
100K
R7
1K
R35 1K
R27 20K
R13
100K
R6
1K
R5
1K
JMP3
4 Pin-T Berg Jumper
1
2
3
4
R24 1K
R12
100K
R38
DNI - 0
R21 20K
JMP10
5Pin-T Berg Jumper
1
2
3
4
5
R4
1K
R11
100K
R51
0
SW1
8-POS 50-MIL SMT
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
R19 1K
BERG1X2J2
R31 20K
R3
1K
JMP7
4 Pin-T Berg Jumper
1
2
3
4
JMP1
4 Pin-T Berg Jumper
1
2
3
4
BERG1X2J3
R59 6.2K
R23 20K
R74 200
R26 1K
R20 1K
JMP2
4 Pin-T Berg Jumper
1
2
3
4
JMP5
4 Pin-T Berg Jumper
1
2
3
4
JMP12
5Pin-T Berg Jumper
1
2
3
4
5
R32 20K
TUSB1044EVM Schematics www.ti.com
8SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
TUSB1044 Active Cable EVM
Figure 6. TUSB1044EVM Schematic (Page 2)

SILKSCREEN:
5V_IN
5V DC Input
5V DC Input
VBUS
2P5VCC 1044_VCC
VBUS
3P3VCC 1044_VCC33
VBUS
D2
Green
J5
DC_POW ER_JACK
1
2
3
R55 DNI - 178K
U2
TPS62080DSGT
VIN
8
EN
1
MODE
3
GND
2
PwPd
9
FB 4
VOS 5
SW 7
PG 6
C35
DNI - 10uF
C34
DNI - 10uF
BERG1X2
J4
DNI - BERG1 X2
J6
D6
DNI - Green
R41
330 Ohm
L1
1uH
R52
DNI - 330 Ohm
C24
10uF
R39 178K
D1
PMEG3050EP, 115
1
2
C26
22uF
R40 0 Ohm
R36
DNI - 178K
L2
DNI - 1uH
U8
DNI - TPS62082DSGT
VIN
8
EN
1
MODE
3
GND
2
PwPd
9
FB 4
VOS 5
SW 7
PG 6
C25
10uF
R22
DNI - 39.2K
R56 DNI - 0 Ohm
C36
DNI - 22uF
5V_IN
U2_SW
U2_PG
U8_SW
U8_PG
www.ti.com TUSB1044EVM Schematics
9
SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
TUSB1044 Active Cable EVM
Figure 7. TUSB1044EVM Schematic (Page 3)

PWB Standoffs
(4 places)
PCB LOGO
Texas Instruments
PCB LOGO
ESD1
PCB LOGO
FCC Disclaimer
PCB LOGO
CE Logo
Mounting Holes
(4 places)
SHUNTS
Assembly Notes
1. Install Label in silkscreened box after final wash
Text shall be 8 pt font. Text shall be per label table
in the PDF schematic.
Variant/Label Table
Variant Label Text
001 TUSB1044RNQEVM
2. To install 4-pin T jumpers, using the part in the
BOM, and cut pin 4, and install it on the left side of
pin 2.
FID1 FID2 FID3
FIDUCIALS
PCB LOGO
WEEE Logo
FID4 FID5 FID6
3. To install 5-pin T jumpers, using the part in the
BOM, cut pin 4 and 5, and install them on left and
right side of pin 2.
SHNT11SHNT9
SHNT7SHNT5
M8M6
SHNT1
M4
SHNT3
M2
SHNT12SHNT10
LB1
SHNT8SHNT6
SHNT2
M7M5
SHNT4
M3M1
PCB1
HSDC008
TUSB1044EVM Schematics www.ti.com
10 SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
TUSB1044 Active Cable EVM
Figure 8. TUSB1044EVM Schematic (Page 4)

www.ti.com Bill of Materials
11
SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
TUSB1044 Active Cable EVM
4 Bill of Materials
Table 6 lists the TUSB1044EVM bill of materials (BOM).
Table 6. TUSB1044 Bill of Materials
Item QTY Reference Part Footprints Manufacturer Manufacturer Part No Description
1 16 C1,C2,C3,C4,C5,C6,C7,C8,C
9,C10,C11,C12,C13,C14,C15,
C16
220nF c0201 TDK Corporation C0603X5R1A224K CAP CER 0.22UF 10V X5R 0201
2 3 C17,C24,C25 10uF 805 Samsung CL21B106KOQNNNE CAP CER 10UF 16V X7R 0805
3 0 C34,C35 DNI - 10uF 805 Samsung CL21B106KOQNNNE CAP CER 10UF 16V X7R 0805
4 3 C18,C19,C20 1uF c0201 Murata Electronics North America GRM033R60J105MEA2D CAP CER 1UF 6.3V X5R 0201
5 8 C21,C22,C23,C27,C28,C29,C
32,C33 0.1uF c0201 Murata Electronics North America GRM033R61A104ME15D CAP CER 0.1UF 10V X5R 0201
6 0 C30,C31 DNI - 0.1uF c0201 Murata Electronics North America GRM155R71C104KA88D CAP CER 0.1UF 10V X5R 0201
7 1 C26 22uF 805 Taiyo Yuden JMK212BJ226KG-T CAP CER 22UF 6.3V X5R 0805
8 0 C36 DNI - 22uF 805 Taiyo Yuden JMK212BJ226KG-T CAP CER 22UF 6.3V X5R 0805
9 1 D1 SCHOTTKY diode_smb NXP Semiconductors PMEG3050EP,115 DIODE SCHOTTKY 30V 5A SOD128
10 5 D2,D3,D4,D5 Green led0805 Lite-On Inc LTST-C170KGKT LED GREEN CLEAR 0805 SMD
11 0 D6 DNI - Green led0805 Lite-On Inc LTST-C170KGKT LED GREEN CLEAR 0805 SMD
12 10 JMP1,JMP2,JMP3,JMP4,JMP
5,JMP6,
JMP7,JMP8,JMP9,JMP11
4 Pin-T Berg Jumper berg2x3tee Samtec Inc HTSW-104-07-G-S 4 Positions Header Connector Through Hole
13 2 JMP10,JMP12 5Pin-T Berg Jumper berg2x5tee Samtec Inc HTSW-105-07-G-S 5 Positions Header Connector Through Hole
14 5 J1,J2,J3,J4 CON02 HDR_THVT_1x2_100_M Samtec Inc HTSW-102-07-G-S 2 Positions Header Connector Through Hole
15 0 J6 DNI - CON02 HDR_THVT_1x2_100_M Samtec Inc HTSW-102-07-G-S 2 Positions Header Connector Through Hole
16 1 J5 DC_PWR_JACK pj-202ah CUI PJ-202AH CONN PWR JACK 2X5.5MM KINKED PIN
17 1 L1 1uH IND_NR3015 Taiyo Yuden NR3015T1R0N FIXED IND 1UH 2.1A 36 MOHM SMD
18 0 L2 DNI - 1uH IND_NR3015 Taiyo Yuden NR3015T1R0N FIXED IND 1UH 2.1A 36 MOHM SMD
19 1 LB1 Label 3M THT-14-423-10 PCB Label 0.650"H x 0.200"W
20 4 M1,M2,M3,M4 NY PMS 440 005 PH Screw B&F Fastener NY PMS 440 0050 PH 40x.5 inch nylon
21 4 M5,M6,M7,M8 1902E Standoff Keystone 1902E Standoff
22 1 P1 Wurth 632712000021 usb-
c_smrt_632_712_000_b6_b7 Wurth Electronics Inc 632712000021 CONN PLUG USB TYPE C SMD
23 1 P2 JAE DX07S024JJ2 USB-C_SMRT_DX07S024JJ2 JAE Electronics DX07S024JJ2R1300 CONN RCPT USB3.1 TYPEC SMD R/A
24 1 PCB1 HSDC008 n/a Any HSDC008 PCB
25 0 R1,R2 DNI - 0 Ohm r0402 Yageo RC0402JR-070RL RES SMD 0.0OHM JUMPER 1/16W 0402
26 17 R3,R4,R5,R6,R7,R8,R9,R10,
R19,R20,R24,R25,R26,R29,R
30,R33,R35
1K r0402 Vishay Dale CRCW04021K00FKED RES SMD 1K OHM 1% 1/16W 0402
27 9 R11,R12,R13,R14,R15,R16,R
17,R18,R42 100K r0402 Yageo RC0402FR-07100KL RES SMD 100K OHM 1% 1/16W 0402
28 12 R21,R23,R27,R28,R31,R32,R
34,R37,R49,R50,R58,R57 20K r0402 Vishay Dale CRCW040220K0FKED RES SMD 20K OHM 1% 1/5W 0402
29 1 R39 178K r0402 Panasonic Electronic Components ERJ-2RKF1783X RES SMD 178K OHM 1% 1/10W 0402
30 0 R36,R55 DNI - 178K r0402 Panasonic Electronic Components ERJ-2RKF1783X RES SMD 178K OHM 1% 1/10W 0402

Bill of Materials www.ti.com
12 SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
TUSB1044 Active Cable EVM
Table 6. TUSB1044 Bill of Materials (continued)
Item QTY Reference Part Footprints Manufacturer Manufacturer Part No Description
31 1 R40 0 Ohm r1206 Vishay Dale CRCW12060000Z0EA RES SMD 0.0 OHM JUMPER 1/4W 1206
32 0 R56 DNI - 0 Ohm r1206 Vishay Dale CRCW12060000Z0EA RES SMD 0.0 OHM JUMPER 1/4W 1206
33 2 R41 330 Ohm r0603 Yageo RC0603FR-07330RL RES SMD 330 OHM 1% 1/10W 0603
34 0 R52 DNI - 330 Ohm r0603 Yageo RC0603FR-07330RL RES SMD 330 OHM 1% 1/10W 0603
35 1 R51 0 r0402 Panasonic Electronic Components ERJ-2GE0R00X RES SMD 0.0OHM JUMPER 1/10W 0402
36 0 R38,R43,R44, DNI - 0 r0402 Panasonic Electronic Components ERJ-2GE0R00X RES SMD 0.0OHM JUMPER 1/10W 0402
37 2 R45,R74 200 r0402 Panasonic Electronic Components ERJ-2RKF2000X RES SMD 200 OHM 1% 1/10W 0402
38 2 R46,R75 1.5K r0402 Panasonic Electronic Components ERJ-2RKF1501X RES SMD 1.5K OHM 1% 1/10W 0402
39 2 R47,R60 3.9K r0402 Panasonic Electronic Components ERJ-2RKF3901X RES SMD 3.9K OHM 1% 1/10W 0402
40 2 R48,R59 6.2K r0402 Panasonic Electronic Components ERJ-2GEJ622X RES SMD 6.2K OHM 5% 1/10W 0402
41 7 R61,R62,R63,R64,R65,R71,R
72 0 r0201 Panasonic Electronic Components ERJ-1GN0R00C RES SMD 0.0OHM JUMPER 1/20W 0201
42 0 R53,R54, R66,R69,R70 DNI - 0 r0201 Panasonic Electronic Components ERJ-1GN0R00C RES SMD 0.0OHM JUMPER 1/20W 0201
43 3 R67,R68,R73 75 r0603 Yageo RC0603JR-0775RL RES SMD 75 OHM 5% 1/10W 0603
44 0 R22 DNI - 39.2K r0402 Yageo RC0402FR-0739K2L RES SMD 39.2K OHM 1% 1/16W 0402
45 12 SHNT1,SHNT2,SHNT3,SHNT
4,SHNT5,SHNT6,SHNT7,SHN
T8,SHNT9,SHNT10,SHNT11,
SHNT12
QPC02SXGN-RC 0.1 Sullins Connector Solutions QPC02SXGN-RC CONN JUMPER SHORTING .100" GOLD
46 1 SW1 8-POS 50-MIL SMT SW_SMVT_SPST_TDA08 C&K Components TDA08H0SB1 SWITCH SLIDE DIP SPST 25MA 24V
47 1 U1 TUSB1044 40 pin QFN Texas Instruments TUSB1044RNQ USB Type-C DP ALT Mode, 10 Gbps Linear Redriver Crosspoint
Switch
48 1 U2 TPS62080DSGT dsg Texas Instruments TPS62082DSGT 1.2A High Efficient Step Down Converter in 2x2mm SON Package.
3.3 Vout (Min)
49 1 U3 TPD6S300 ruk0020b Texas Instruments TPD6S300RUKR USB Type-C™ Port Protector: Short-to-VBUS Overvoltage and IEC
ESD Protection
50 2 U4,U5 TPD4E02B04 dqa0010a Texas Instruments TPD4E02B04DQAR 4-Channel ESD Protection Diode for USB Type-C and HDMI 2.0
51 0 U8 DNI - TPS62082 dsg Texas Instruments TPS62082DSGT 1.2A High Efficient Step Down Converter in 2x2mm SON Package.
3.3 Vout (Min)

www.ti.com Revision History
13
SLLU265B–March 2018–Revised August 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
Revision History
Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from A Revision (April 2018) to B Revision .................................................................................................... Page
• Deleted TUSB212 support throughout the document. ............................................................................... 1
Revision History
Changes from Original (March 2018) to A Revision ....................................................................................................... Page
• Added TUSB212 support throughout the document.................................................................................. 1
• Changed Figure 1......................................................................................................................... 2
• Added NOTE: and Figure 3 and Figure 4.............................................................................................. 3
• Changed schematic images: Figure 5 through Figure 8............................................................................. 7
• Changed Table 6......................................................................................................................... 11

STANDARD TERMS FOR EVALUATION MODULES
1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or
documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance
with the terms set forth herein. User's acceptance of the EVM is expressly subject to the following terms.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License
Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for a nonconforming EVM if (a) the nonconformity was caused by
neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have
been altered or modified in any way by an entity other than TI, (b) the nonconformity resulted from User's design, specifications
or instructions for such EVMs or improper system design, or (c) User has not paid on time. Testing and other quality control
techniques are used to the extent TI deems necessary. TI does not test all parameters of each EVM.
User's claims against TI under this Section 2 are void if User fails to notify TI of any apparent defects in the EVMs within ten (10)
business days after delivery, or of any hidden defects with ten (10) business days after the defect has been detected.
2.3 TI's sole liability shall be at its option to repair or replace EVMs that fail to conform to the warranty set forth above, or credit
User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty
period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or
replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be
warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3Regulatory Notices:
3.1 United States
3.1.1 Notice applicable to EVMs not FCC-Approved:
FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software
associated with the kit to determine whether to incorporate such items in a finished product and software developers to write
software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or
otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition
that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference.
Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must
operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.

FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 or RSS-247
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required to follow the
instructions set forth by Radio Law of Japan, which includes, but is not limited to, the instructions below with respect to EVMs
(which for the avoidance of doubt are stated strictly for convenience and should be verified by User):
1. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
2. Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
3. Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.

【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
2. 実験局の免許を取得後ご使用いただく。
3. 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http:/
/www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
3.4 European Union
3.4.1 For EVMs subject to EU Directive 2014/30/EU (Electromagnetic Compatibility Directive):
This is a class A product intended for use in environments other than domestic environments that are connected to a
low-voltage power-supply network that supplies buildings used for domestic purposes. In a domestic environment this
product may cause radio interference in which case the user may be required to take adequate measures.
4EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.

6. Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY MATERIALS PROVIDED WITH THE EVM (INCLUDING, BUT NOT
LIMITED TO, REFERENCE DESIGNS AND THE DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL
FAULTS." TI DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT
NOT LIMITED TO ANY EPIDEMIC FAILURE WARRANTY OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADE
SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS SHALL BE
CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY OTHER INDUSTRIAL OR
INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD PARTY, TO USE THE
EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY INVENTION, DISCOVERY OR
IMPROVEMENT, REGARDLESS OF WHEN MADE, CONCEIVED OR ACQUIRED.
7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS. THIS OBLIGATION SHALL APPLY
WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY OTHER LEGAL
THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8. Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS OR THE USE OF THE EVMS , REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, COST OF REMOVAL OR
REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, RETESTING,
OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS, LOSS OF SAVINGS, LOSS OF
USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL BE BROUGHT AGAINST TI
MORE THAN TWELVE (12) MONTHS AFTER THE EVENT THAT GAVE RISE TO THE CAUSE OF ACTION HAS
OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY USE OF AN EVM PROVIDED
HEREUNDER, INCLUDING FROM ANY WARRANTY, INDEMITY OR OTHER OBLIGATION ARISING OUT OF OR IN
CONNECTION WITH THESE TERMS, , EXCEED THE TOTAL AMOUNT PAID TO TI BY USER FOR THE PARTICULAR
EVM(S) AT ISSUE DURING THE PRIOR TWELVE (12) MONTHS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE
CLAIMED. THE EXISTENCE OF MORE THAN ONE CLAIM SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated

IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES
Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,
reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are
developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you
(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of
this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources.
You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your
applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications
(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You
represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)
anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that
might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you
will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any
testing other than that specifically described in the published documentation for a particular TI Resource.
You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include
the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO
ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS.
TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT
LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF
DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,
COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR
ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your non-
compliance with the terms and provisions of this Notice.
This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services.
These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation
modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated