The Land of Nod Simple Desk Hutch User manual

WARNING: Adult Assembly Required
!
1Insert 2 cams into top and bottom crossbar as
shown. Make sure arrows on each cam points
toward nearest edge with holes.
1 - shelf
Made in Vietnam - r06 Page 1 of 4
Thank you for purchasing the Simple Desk Hutch.This
page lists all the contents included in the box. Please
take the time to identify the hardware as well as the
individual components to this product. As you unpack
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
12 - bolts
ASSEMBLY HARDWARE
1 - top panel 2 - side panels
(1 left, 1 right)
1 - top
crossbar
1 - bottom
crossbar
1 - back panel
12 - flat
washers
8 - screws 4 - cams 4 - cam
screws
12 - spring
washers
TOOLS REQUIRED
phillips head screwdriver
Missing hardware? Please call 800.933.9904 for replacements.
NOTE: Contains small parts. Keep away from small children.
bottom
crossbar
top
crossbar
2 - connecting
brackets
NOTE: Make sure arrows on
each cam point towards
nearest edge with holes
flat head screwdriver
(We recommend the use of hand tools instead of power tools)
SIMPLE
DESK HUTCH
COMPONENTS

2
Insert 2 cam screws into left and right side
panels as shown. Secure, but do not over
tighten cam screws with a flat head screw-
driver. 3
Fit dowels of top and bottom crossbars into
corresponding holes of left side panel as
shown. With a phillips head screwdriver, turn
each cam clockwise until it securely engages
each cam screw.
4Slide back panel into corresponding grooves of
assembled unit as shown. 5
Fit dowels of shelf into corresponding holes of
assembled unit shown. Secure with 2 bolts, 2
spring washers and 2 flat washers using a
screwdriver. Do not over tighten the bolts.
Made in Vietnam - r06 Page 2 of 4
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
right side
panel
left side
panel
left side
panel
bottom
crossbar
top
crossbar
back
panel
shelf
NOTE: Do not over
tighten the bolts
NOTE: Do not
over tighten the
cam screws
SIMPLE
DESK HUTCH

6
A) Fit dowels of assembled unit into
corresponding holes of right side panel as
shown. Secure all cams.
B) Secure right side panel to shelf with 2 bolts,
2 spring washers and 2 flat washers. 7Fit dowels of assembled unit into corresponding
holes of top panel as shown. Secure with 8
bolts, 8 spring washers and 8 flat washers.
8
With the assistance of another adult, carefully
position unit upright and place onto desk (sold
separately) as shown. Attach 2 connecting
brackets to desk and hutch assembly with 4
screws per bracket as shown, using a
screwdriver.
Assembly is now complete.
Made in Vietnam - r06 Page 3 of 4
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
unit is finished with a protective clear lacquer.
right side
panel
top
panel
desk
(sold separately)
hutch
B
A
A
SIMPLE
DESK HUTCH

For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is
essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach 2 mounting brackets to top of unit with 2 small screws per bracket as shown. Secure, but do not over tighten,
with a phillips head screwdriver.
B) Determine the final location of unit. Mark each position on the wall, approximately 2" below the mounting bracket
mounted to the back of the unit.
C) Drill 2 holes into marked positions on the wall and into a wall stud. If the wall stud is not available, drill a hole in the wall
that is slightly smaller in diameter than the anchor. Gently tap 2 plastic anchors until the flange of each anchor is flush with
the wall.
D) Attach 2 mounting brackets to the wall with 2 large screws per bracket as shown. Using a screwdriver, make sure the
screws are secured through the mounting bracket and into the plastic anchor in the wall.
E) With the assistance of another adutl, position the unit so the mounting brackets on the back edge are aligned with the
mounting brackets on the wall.
F) Attach 2 wall straps to corresponding 2 mounting brackets as shown. Lace one end of the wall strap through both
brackets and into the other end of the strap. Pull tightly on the wall strap to secure.
Wall mounting assembly is now complete.
Serious or fatal crushing injuries can occur from furniture
tip over. Use of tip-over restraints may only reduce, but
not eliminate, the risk of tip-over. To help prevent tip-over,
install tip restraint per instructions below.
WARNING
!
Missing hardware? Please call 800.933.9904
for replacements. NOTE: Contains small
parts. Keep away from small children.
MOUNTING HARDWARE
TOOLS REQUIRED
WALL MOUNTING ASSEMBLY
power drill
(for pilot holes only)
phillips head screwdriver
4 - mounting
brackets
4 - large
screws
4 - small
screws
2 - wall
straps
4 - plastic
anchors
A
C
D
F
SIMPLE
DESK HUTCH
Made in Vietnam - r06 Page 4 of 4
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com