The Land of Nod Bankable 60 BOOKCASE User manual

TOOLS REQUIRED
WARNING: Adult Assembly Required
!
Made in Vietnam - r04 Page 1 of 4
Thank you for purchasing the Bankable 60”Bookcase.
This page lists all the contents included in the box.
Please take the time to identify the hardware as well as
the individual components to this product. As you
unpack and prepare for assembly, place the contents on
a carpeted or padded area to protect them from
damage.
Note: 2 people are required to safely assemble this product.
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
26 - spring
washers
ASSEMBLY HARDWARE
26 - bolts
2 - side panels
(1 left, 1 right)
1 - front panel
phillips head screwdriver
Missing hardware? Please call 800.933.9904 for replacements.
NOTE: Contains small parts. Keep away from small children.
(We recommend the use of hand tools instead of power tools)
BANKABLE
60”BOOKCASE
COMPONENTS
26 - flat
washers
26 - wood
dowels
26 - screws
1 - bottom
panel
4 - shelves
(shown in smallest
to largest)
1 - crossbar
3 - back panels
(1 left, 1 center, 1 right)

1
Place left and right side panels onto a clean,
padded surface as shown. Insert 13 wood
dowels into left and right side panels as
shown. 2
3 4
A. Fit bottom panel and front panel onto
dowels of right side panel. Secure front/bottom
panels with 4 bolts,4spring washers and 4 flat
washers as shown.
B. Secure bottom panel to front panel with 2
bolts, 2 spring washers and 2 flat washers as
shown.
Made in Vietnam - r04 Page 2 of 4
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
right side
panel
left side
panel
NOTE: Do not over
tighten the bolts
BANKABLE
60”BOOKCASE
A. Set left side panel aside. Fit 4 shelves
(from smallest to largest) onto corresponding
dowels of right side panel as shown.
B. Using a phillips head screwdriver, attach
each shelf with 2 bolts, 2 spring washers and 2
flat washers as shown. Do not over tighten the
bolts.
NOTE: Make sure
apron and front
edge of each shelf
are positioned as
shown
A. Fit crossbar onto dowel of right side panel
as shown.
B. Fit left side panel onto corresponding
dowels of assembly and secure with 12 bolts, 12
spring washers and 12 flat washers as shown.
B
B
front panel
bottom panel
smallest shelf
largest shelf
right side panel
left side panel
crossbar
A
B
A
A
B

5
With the assistance of another adult, position
assembly upright as shown. Attach left and
right back panels to back of assembly with 8
screws per panel. Secure, but do not over
tighten, screws with a screwdriver. 6Attach center back panel with 10 screws as
shown.
Assembly is now complete.
Made in Vietnam - r04 Page 3 of 4
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
unit is finished with a protective clear lacquer.
right back panel
BANKABLE
60”BOOKCASE
left back panel
center back
panel
NOTE: Do not
over tighten the
screws

For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is
essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach 2 mounting brackets to back of unit using 2 small screws per bracket as shown.
B) Determine the final location of unit. Mark position on the wall, approximately 2" below each wall bracket mounted
to the back of the unit.
C) Drill holes into marked positions on the wall and into a wall stud. If the wall stud is not available, drill a hole in the wall
that is slightly smaller in diameter than the anchor. Gently tap 4 plastic anchors until the flange of each anchor is
flush with the wall.
D) Attach 2 mounting brackets to the wall by inserting 2 large screws per bracket. Using a screwdriver, make sure
each screw is secured through the mounting bracket and into the plastic anchor in the wall.
E) With assistance of another adult, position the unit so the mounting brackets on the back edge are aligned with the
mounting brackets on the wall.
F) Attach 2 wall straps to corresponding mounting brackets as shown. Lace one end of the wall strap through both
brackets and into the other end of the strap. Pull tightly on the wall strap to secure.
Wall mounting assembly is now complete.
Serious or fatal crushing injuries can occur from furniture
tip over. Use of tip-over restraints may only reduce, but
not eliminate, the risk of tip-over. To help prevent tip-over,
install tip restraint per instructions below.
WARNING
!
MOUNTING HARDWARE
TOOLS REQUIRED
WALL MOUNTING ASSEMBLY
power drill
(for pilot holes only)
phillips head screwdriver
BANKABLE
60”BOOKCASE
Made in Vietnam - r04 Page 4 of 4
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
A
C
D
small
screw
mounting
bracket
plastic
anchor
large
screw
wall
strap
mounting
bracket
4 - small
screws
4 - large
screws
4 - plastic
anchors
4 - mounting
brackets
Missing hardware? Please call 800.933.9904
for replacements. NOTE: Contains small
parts. Keep away from small children.
2 - wall straps