The Land of Nod Oak Park User manual

Made in Vietnam - r04 Page 1 of 4
ASSEMBLY HARDWARE
COMPONENTS
TOOLS REQUIRED
Thank you for purchasing the Oak Park Bookcase.
This page lists all the contents included in the box.
Please take the time to identify the hardware as well as
the individual components to this product. As you
unpack and prepare for assembly, place the contents on
a carpeted or padded area to protect them from
damage.
Note: 2 people are required to safely assemble this product.
Customer Service 800.933.9904 | Latest instructions available on www.landofnod.com
1
With the assistance of another adult, carefully
place left and right side panel onto clean,
padded surface. Insert 7 wood dowels into left
and right side panel as shown.
4 - large
bolts
14 - wood
dowels
4 - large flat
washers
4 - large
spring
washers
1 - top back
panel
4 - medium
bolts
16 - small
flat washers
16 - small
spring
washers
Missing hardware? Please call 800.933.9904 for replacements.
NOTE: Contains small parts. Keep away from small children.
1 - top shelf
2 - side panels
(1 left, 1 right)
1 - base
1 - bottom shelf
1 - middle shelf
4 - feet2 - doors
(1 left, 1 right)
1 - back panel
12 - small
bolts
left side
panel
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
right side
panel
OAK PARK
BOOKCASE
WARNING: Adult Assembly Required
!

Made in Vietnam - r04 Page 2 of 4
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
4
23
5
Fit dowels of right side panel into corresponding
holes of top shelf, middle shelf and bottom shelf.
Secure each shelf with 2 small bolts, 2 small
spring washers and 2 small flat washers using a
phillips head screwdriver. Do not over tighten the
bolts.
Fit dowels of left side panel into corresponding
holes of assembled unit. Secure each shelf with 2
small bolts, 2 small spring washers and 2 small
flat washers using screwdriver.
A. With the assistance of another adult, slide back
panel into corresponding grooves of assembled
unit as shown.
B. Slide top back panel into corresponding
grooves of assembled unit.
Attach feet to base as shown. Secure each
foot with 1 large bolt, 1 large spring washer
and 1 large flat washer, using a screwdriver.
NOTE: Do not
over tighten the
bolts
right side
panel
AB
middle shelf
top shelf
bottom shelf
back panel
left side panel
base
foot
top back
panel
OAK PARK
BOOKCASE

OAK PARK
BOOKCASE
Made in Vietnam - r04 Page 3 of 4
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
6
7
Fit dowels of left and right side panels into
corresponding holes of base assembly. Secure
with 4 medium bolts, 4 small spring washers and
4 small flat washers.
With the assistance of another adult, carefully place
unit upright. Insert bottom edge of right door into
bottom back groove of unit as shown. Press and hold
down both levers (located at the back of door) to
insert top edge of door into top back groove of unit.
Release levers to secure door. Repeat for left door
using the front groove of unit.
Assembly is now complete.
right door
left door
NOTE: Do not
over tighten the
bolts
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as the
wood is finished with a protective clear lacquer.
CLEANING AND CARE
base
assembly

For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is
essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach mounting bracket to top center of unit using 2 small screws.
B) Determine the final location of unit. Mark position on the wall, approximately 2" below the mounting bracket mounted to
the back of the unit.
C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in the wall that is slightly smaller in diameter than
the anchor. Gently tap the plastic anchor until the flange of the anchor is flush with the wall.
D) Attach the mounting bracket to the wall by inserting 2 large screws through the mounting bracket and into the wall
anchor in the wall.
E) Place the unit so the mounting bracket on the back edge is allowed with the wall bracket.
F) Lace one end of the wall strap through both brackets, and into the other end of the strap.
G) Pull the strap tightly until secure.
Repeat step A-G for remaining wall mounting assembly.
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a qualified
professional.
Wall mounting assembly is now complete.
A
C
D
small
screw
mounting
bracket
plastic
anchor
large
screw
wall
strap
mounting
bracket
Serious or fatal crushing injuries can occur from furniture
tip over. Use of tip-over restraints may only reduce, but
not eliminate, the risk of tip-over. To help prevent tip-over,
install tip restraint per instructions below.
WARNING
!
4 - small
screws
4 - large
screws
4 - plastic
anchors
4 - mounting
brackets
Missing hardware? Please call 800.933.9904
for replacements. NOTE: Contains small
parts. Keep away from small children.
MOUNTING HARDWARE
2 - wall straps
TOOLS REQUIRED
WALL MOUNTING ASSEMBLY
power drill
(for pilot holes only)
phillips head screwdriver
Made in Vietnam - r04 Page 4 of 4
Customer Service 800.933.9904 | Latest instructions available on www.landofnod.com
OAK PARK
BOOKCASE