The Land of Nod Taylor Toddler Rail User manual

• Failure to follow these warnings and assembly instructions could result in serious injury or death.
• Read all instructions before assembling toddler rail. Keep instructions for future use.
• For toddler bed use, the minimum age shall be no less than 15 months, and the maximum weight shall not be
greater than 50 lb (22.7 kg).
• Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under an
infant.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
Strangulation Hazard:
• Strings can cause strangulation! DO NOT place items with a string, cord or ribbon around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over crib or toddler bed, or attach strings to toys for any
reason.
• To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
• DO NOT place crib or toddler bed near windows where cords from blinds or drapes may strangle a child.
Fall Hazard:
• When child is able to pull to standing position, set mattress to lowest position and remove bumper pads, large toys
and other objects that could serve as steps for climbing out.
• When child is able to climb out or reaches the height of 35 inches (90 cm), the crib shall no longer be used and the
child should be placed in a youth or regular bed.
CAUTION: ANY MATTRESS USED IN THIS CRIB
MUST BE AT LEAST 27-1/4 INCHES (69 cm) BY 51-5/8
INCHES (131 cm) WITH A THICKNESS NOT EXCEEDING
6 INCHES (15 cm).
• Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assembly and
frequently during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if any parts are missing,
damaged, or broken. Contact The Land of Nod® for replacement parts and instructional literature if needed. DO
NOT substitute parts.
• If refinishing, use a non-toxic finish specified for children’s products.
• Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
• Infants can suffocate in gaps between crib sides and a mattress that is too small.
• Periodically check to see that all bolts are securely tightened.
• To clean toddler rail: Wipe with clean soft cloth dampened with a mild cleanser and water. Rinse with clean water
using a soft cloth, and dry thoroughly.
• Follow warnings on all products in a toddler rail.
• When a vaporizer is in use, always aim vapor steam away from the toddler rail as well as away from other wood
furniture.
WARNING:
!
!
WARNING:
!
The Land of Nod
Made in Vietnam - r06
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Taylor Toddler Rail Assembly Instructions

The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Taylor Toddler Rail Assembly Instructions
Page 1 of 6
Made in Vietnam - r06
This page lists the contents included in the box. Please take
time to identify the hardware as well as the individual
components of the product. As you unpack and prepare for
assembly, place the contents on a carpeted or padded area
to protect them from damage. Please follow the assembly
instructions closely. Improper assembly can result in
personal or property damage.
Note: 2 adults are required to safely assemble this product.
WARNING:
CHOKING HAZARD - SMALL PARTS
Small parts present in unassembled state.
Adult assembly required.
1 - Large Allen
wrench
1 - Small Allen
wrench
4 - Bolt caps
2 - End panel bolts
(New hardware for toddler rail)
2 - Small bolts
3 - Flat
washers
(pre-attached
to bolts)
3 - Spring
washers
(pre-attached
to bolts)
3 - Half-moon
brackets
3 - Large bolts 4 - Support
pin
NOTE: Hardware will be
re-used from the Taylor
crib assembly unless
otherwise noted

1
2
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Taylor Toddler Rail Assembly Instructions
Page 2 of 6
Made in Vietnam - r06
With the assistance of another adult, remove mattress panel from corresponding support pins of crib assembly. From
the top of mattress panel, remove bolt caps from each support pin with a large Allen wrench. At this point, remove
each support pin from corresponding corners. Set mattress panel and hardware aside until further instructions.
Carefully remove 1 side panel from end panels as shown. Using a small Allen wrench, unfasten 3 large bolts, 3 spring
washers, 3 flat washers and 3 half-moon brackets from bottom of side panel and crossbar as shown. Using a small Allen
wrench, unfasten 2 small bolts, 2 spring washers and 2 flat washers from top of side panel as shown. Set hardware aside
until further instructions.
bottom of
crossbar
top of
side panel
bottom of
side panel

Fit pre-attached dowels of toddler rail to corresponding holes of end panels as shown. Using a small Allen wrench,
loosely attach 3 large bolts, 3 spring washers, 3 flat washers and 3 half-moon brackets to assembly as shown. Do not
fully tighten bolts until further instructions.
3
4
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Taylor Toddler Rail Assembly Instructions
Page 3 of 6
Made in Vietnam - r06
Remove side panel from assembly and set aside.

5
6Determine the lowest height as shown. Re-insert each support pin into corresponding corner as shown. Make sure support
pin is securely engaged with assembly.
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Taylor Toddler Rail Assembly Instructions
Page 4 of 6
Made in Vietnam - r06
Position assembly upright as shown. Loosely attach toddler rail to each end rail with 1 small bolt, 1 spring washer and 1
flat washer, using a small Allen wrench.
low

7
8
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Taylor Toddler Rail Assembly Instructions
Page 5 of 6
Made in Vietnam - r06
NOTE: Make sure
metal plate of mattress
panel is at the bottom
during assembly
With the assistance of another adult, fit mattress panel into corresponding support pins of toddler bed assembly. From
the top of mattress panel, attach bolt caps onto each support pin with a large Allen wrench.
Insert 2 end panel bolts to corresponding holes of end panels as shown, using a small Allen wrench. At this point, fully
tighten all bolts and store any unused hardware/components for future use.
Assembly is now complete.

CLEANINGANDCARE:
Cleansurfaceswithadryordampsoftcloth.Donotuseabrasivecleaners. Periodically check and tighten hardware as necessary.

Once the crib is in use, periodically check to make sure all bolts are tight, and tighten as necessary. Keep these
instructions for future use.
MAINTENANCE
Upon completion of assembly, be sure all screws, bolts and fastening devices have been tightened securely.
Periodically repeat this check to make sure all screws, bolts and fastening devices are tight. Before each usage or
assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use crib if parts
are missing or broken. DO NOT substitute parts. DO NOT make any alteration to this crib.
CLEANING
Mix together a mild solution of gentle dishwashing liquid and water, apply to crib surface using a soft clean cloth
lightly dampened in the solution. Rinse with clean water again using a soft clean cloth, then dry all surfaces
thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL OR COARSE RAGS
SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
STORAGE
After completing the assembly process you are advised to read and beware of all WARNINGS, CAUTIONS,
CLEANING, STORAGE, USE AND MAINTENANCE notices contained in these instructions. For long term storage of
the crib, store in a cool, dry place and keep away from moisture and extreme temperature changes.
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Taylor Toddler Rail Assembly Instructions
Page 6 of 6
Made in Vietnam - r06