The Land of Nod Harmony Toddler Rail User manual

WARNING:
CHOKING HAZARD - SMALL PARTS
Small parts present in unassembled state.
Adult assembly required.
This page lists the contents included in the box. Please take
time to identify the hardware as well as the individual
components of the product. As you unpack and prepare for
assembly, place the contents on a carpeted or padded area
to protect them from damage. Please follow the assembly
instructions closely. Improper assembly can result in
personal or property damage.
Note: 2 adults are required to safely assemble this product.
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Harmony Toddler Rail Assembly Instructions
Page 1 of 4
Made in Vietnam - r06
1 - Toddler
rail panel
*Hardware will be re-used from Harmony Crib construction
Bolts
Spring
washers
Flat
washers
Bolt
caps
Large
Allen wrench
Small
Allen wrench
Corner
supports

Using an Allen wrench, carefully unfasten 4 bolts, 4 spring washers and 4 flat washers to remove the front rail panel
from the crib assembly. Store front rail panel and set hardware aside until further instructions.
If mattress support is NOT in lowest position, remove 4 bolt caps with large allen wrench and remove mattress
support. Reposition corner supports to the lowest position. Place mattress support into corresponding corner
supports of assembly. Secure each corner support with a bolt cap, using large allen wrench.
1
2
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Harmony Toddler Rail Assembly Instructions
Page 2 of 4
Made in Vietnam - r06

3
Fit pre-assembled wood dowels of toddler rail panel into corresponding holes of crib assembly as shown. Attach toddler
rail panel with 4 bolts, 4 spring washers and 4 flat washers. Secure bolts with an Allen wrench.
Assembly is now complete.
Made in Vietnam - r06
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Page 3 of 4
Harmony Toddler Rail Assembly Instructions

Made in Vietnam - r06
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Page 4 of 4
Harmony Toddler Rail Assembly Instructions
Once the toddler bed is in use, periodically check to make sure all bolts are tight, and tighten as
necessary. Keep these instructions for future use.
MAINTENANCE
Upon completion of assembly, be sure all screws, bolts and fastening devices have been tightened
securely. Periodically repeat this check to make sure all screws, bolts and fastening devices are tight.
Before each usage or assembly, inspect toddler bed for damaged hardware, loose joints, missing
parts or sharp edges. DO NOT use toddler bed if parts are missing or broken. DO NOT substitute
parts. DO NOT make any alteration to this toddler bed.
CLEANING
Mix together a mild solution of gentle dishwashing liquid and water, apply to toddler bed surface
using a soft clean cloth lightly dampened in the solution. Rinse with clean water again using a soft
clean cloth, then dry all surfaces thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS,
SCOURING PADS, STEEL WOOL OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
STORAGE
After completing the assembly process you are advised to read and beware of all WARNINGS,
CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE notices contained in these instructions.
For long term storage of the toddler bed, store in a cool, dry place and keep away from moisture and
extreme temperature changes.