The One Studio TH-373 MINI PROFILE 60W Zoom User manual

1
MINI PROFILE 60W Zoom
User Manual
TH-373

2
SAFETY INSTRUCTIONS
CAUTION
Be careful with your operations.With a dangerous voltage you can suffer
a dangerous electric shock when touching wires!
This device has left the factory in perfect condition. In order to maintain this condition and
to ensure a safe operation, it is absolutely necessary for the user to follow the safety
instructions and warning notes written in this user manual.
If the device has been exposed to temperature changes due to environmental changes, do
not switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be
earthed.
The electric connection must carry out by qualified person. The device shall only be used
with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be
the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only
handle the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does
not necessarily mean that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance
with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat
radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in order to
avoid a hazard.
1
IMPORTANT
Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or
problems.

3
Unpacking
Thank you for choosing our MINI PROFILE 60MZ-WW. For your own safety, please read this
manual before installing the device. This manual covers the important information on installation
and applications. Please install and operate the fixture with following instructions. Meanwhile,
please keep this manual well for future needs.
The MINI PROFILE 60MZ-WW is made of a new type of high temperature strength of die-casting
aluminum with nice outlook. The fixture is designed and manufactured strictly following CE
standards, complying with international standard DMX512 protocol. It's available independently
controlled and link able with each other for operation. And it is applicable for
useum, Retail store, Restaurant, Children theater, Gallery.
The MINI PROFILE 60MZ-WW adopts 1PC 60W COB LED (CW) which features high brightness
and stability. Please carefully unpack it when you receive the fixture and check whether it is
damaged during the transportation. And please check whether the following items are included
inside the box:
1②
①MINI PROFILE 60MZ-WW
1PC
②DMX cable
1PC
③POWER cable
1PC
④User manual
1PC
2
③
②
③
④

4
FEATURES & SPECIFICATIONS
Feature：
* 1*60W COB LED (Warm white)
*50,000 hours life span and low power consumption
*Color Rendering Index(CRI): Ra≥95
*Optimized high definition optical system for improved photometric performance and field uniformity
*Projector-quality, high contrast aspheric lens
*Glass reflector that removes greater than 90% infrared radiation (heat) and reflects greater than
95% of visible light
*Manual zoom system from 20-35°
*Flat and even spot image,Smooth manual focus system
*Housing made by rugged, die cast aluminum alloy
*Thermally insulated rear handle
*Thermally insulated knobs and single aluminum handle for installing
*4 Metal spot cutting slots
*Color frame as optional,Metal gobo slot as optional
*0-100% Smooth and precise linear dimmer
*25T/sec high speed shutter/strobe effect with variable speed
*1/3DMX channels USITT DMX-512
*DMX512, master-slave, or auto operation
*4-Button digital display
*3-Pin XLR connectors IN/OUT
*Low noise fan integrated with copper liquid cooling system
*-30-40℃Max ambient temperature
*IP20 protection rating
Specifications：
*Input Voltage:AC100-240V 50/60Hz
*Max. Power: 60W
*Dimensions: 344(D)*196(W)*235.9(H)mm
*Packing Size: 445(D)*225(W)*185(H)mm
*Net Weight: 2.28kg
*Gross Weight: 3.3kg
3

5
DMX-512 CONTROL CONNECTIONS
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other
side to the male 3-pin XLR input of the moving head. You can chain multiple
Moving head together through serial linking. The cable needed should be two core, screened
cable with XLR input and output connectors. Please refer to the diagram below.
DMX-512 connection with DMX terminator
4
POWER IN
DMX INPUT
DMX OUTPUT

6
DMX Output
3-Pin XLR Socket
DMX Input
3-Pin XLR Socket
1:Ground
2:Data(-)
3:Data(+)
COMMON
DMX+
DMX-
DMX 512 OUT
3-PIN XRL
DMX 512 IN
3-PIN XRL
120Ω
Pin2
Pin3
For installations where the DMX cable has to run a long
distance or is in an electrically noisy environment, such as
in a discotheque, it is recommended to use a DMX
terminator. This helps in preventing corruption of the digital
control signal by electrical noise. The DMX terminator is
simply an XLR plug with a 120 Ω resistor connected
between pins 2 and 3,which is then plugged into the output
XLR socket of the last fixture in the chain. Please see
illustrations below.

7
Product Features
2 kinds of running model
External control mode (Slave model)
DMX 512 controller control(2 kinds channel modes)
Master/salve model control (auto match the signal from controller and the Master
light, no need to set by menu)
static mode (Master model)
It can fix any color without the controller ,also work this color with strobe
Non-linear dimmer and linear dimmer
The speed of dimmer can be set under the controller control
Screen Protect
It will enter blank screen without any operate on the keyboard in 30 seconds . Press any
keys then it can quit screen protection.
Temperature Protection
It can be set to temperature protection mode
Speed of the Fan
The fan will start to work when the working temperature reach 40 degree, and the speed
will be changed according to the change of temperature.
Can be Reverse display
Multi-light working in the same time
When using controller to control multi lights to work in strobe, the controller just send the
channel data . The strobe effect will be depend on each light itself . And please take attention for
the follow situation:
1. There will be many situations make the lights are not synchronization in the beginning.
(For example: the different time of opening the light , or different time of them connect to the
controller) .In this case, you can change value of the controller( for example push 20 to 0, and
back to 20), then it can be synchronization.
2. Due to crystal frequency of different lights are not the same exactly, so it may not be
synchronization after long time.
3. If need to keep synchronization for long time, there are two ways to do so:
A. Using the controller to edit program make the strobe, auto run effect,then they must be
synchronization.
B. Using the Maser/Slave model
5

8
MENU OPERATIONS
Menu：
The first list is the main menu (press MENU to
exchange), the second list is submenu (press ENTER to
get in or exchange)
If the menu include the decimal point, that’s the data,
and it can be set by the Key of Up/Down.
Key operation：
Key of “MENU” (Press it and can save the data)
If it’s the main menu, it will exchange to next main
menu.
If it’s the submenu , it will back to main menu.
Key of “ENTER” (Press it and can save the data)
If it’s the main menu and it have submenu, it will
enter the submenu.
If it’s the submenu, it will exchange to the next
submenu
Key of “UP/DOWN”
It’s no function if the menu not include the decimal
point.
If the menu include the decimal point, it can set the
data after the decimal point. And it need to press
“ENTER” to save the data.
6

9
Menu
State
Operation
Remark
Main Menu
Vice Menu
No vice menu
A: advance
UP/DOWN
adjust ID adress
disconnect the
controller and
connect the master
light, then it will
follow the master
light.
It will flicker if no
signal.
External control mode
(standard channel
model)
ENTER
save the ID
address
No vice menu
d: dmx
UP/DOWN
adjust ID address
External control mode
(Basic channel model)
ENTER
Save the ID
address
two vice menu
StAt: static
ENTER
enter vice menu
Static model
C: Color
UP/DOWN
change value of
color
Set the color
ENTER
save the data
change to the
vice menu
St: strobe
UP/DOWN
change value of
strobe
strobe and its speed
ENTER
save and
exchange
two vice menu
tEMp: temperature
ENTER
enter the vice
menu
temperature control
current temperature
ENTER
change to vice
menu
t: top
UP/DOWN
change the data
of temperature
protect
set the protect
temperature
ENTER
save and change
No vice menu
diSP: display
ENTER
reverse the
display
set to show reverse
display
No vice menu
rESt: reset
ENTER
enter the
interface of key
the password is “UP
DONW UP DOWN”
return Initial State
return Initial State

10
DMX CHANNELS
1CH Chanel Model
Channel
Data
Function
1
0~255
Dimmer
3CH Chanel Model
Channel
Data
Function
Remark
1
0~255
Dimmer
2
0~10
Default dimmer delay
11~15
No dimmer delay
16~255
Dimmer delay option
16 is the shortest delay, 255 is the longest
delay
3
0-10
No Strobe
11-255
Strobe Speed (255 the
fast)
7

11
OPERATION INSTRUCTIONS
·The MINI PROFILE 60MZ-WW is an LED studio light for on-site decoration purpose.
·Don't turn on the fixture if it's been through severe temperature difference like after transportation
because it might damage the light due to the environment changes. So make sure to operate the
fixture until it is in normal temperature.
·This light should be keep away from strong shaking during any transportation or movement.
·Don't pull up the light by only the head, or it might cause damages to the mechanical parts.
·Don't expose the fixture in overheat, moisture or environment with too much dust when installing
it. And don't lay any power cables on the floor. Or it might cause electronic shock to the people.
·Make sure the installation place is in good safety condition before installing the fixture.
·Make sure to put the safety chain and check whether the screws are screwed properly when
installing the fixture.
·Make sure the lens are in good condition. It's recommended to replace the units if there are any
damages or severe scratch.
·Make sure the fixture is operated by qualified personnel who knows the fixture before using.
·Keep the original packages if any second shipment is needed.
·Don't try to change the fixtures without any instruction by the manufacturer or the appointed
repairing agencies.
·It is not in warranty range if there are any malfunctions from not following the user manual to
operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.
INSTALLATIONS
For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas
were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device's weight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
From a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept at
least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).
8
9

12
Please ensure that the led mini profile spotlight is hung using the appropriate "C" clamp or half
cheeseboro. A safety chain or cable should also be used as a secondary point of holding the
fixture in case the clamp comes loose. Never hang the fixture without a safety chain or cable.
There is an eye-bolt on the back of the fixture to which the safety chain or cable can threaded
through and then hung from the secondary point. Make sure the Gel frame (Gel holder) is clipped
into position correctly and cannot come loose.
If you are not qualified or have any doubts about hanging the led mini profile spotlight then do NOT
hang it.
Do not clamp the safety cable to the U bracket or clamp. That is not a secondary safety point.
A secondary safety point is any point that will adequately hold the led mini profile spotlight if the
"C" clamp or half cheesboro fails.
Then the safety cable would be the backup and stop the fixture from falling to the ground. So do
NOT fix the safety cable to the same place that the "C"clamp is attached
Floor Projection

13
Cleaning and maintenance
Now ignoring maintenance and cleaning is very good way of creating problems "down the road"
and many companies and installations do just that. However the net result is, no matter what the
fixture, premature failure!
Changing the oil in a car, most people do on a regular basis.
So with the fixtures, regular maintenance it an excellent practice, if you want the fixtures to last.
So what is the maintenance for the fixture?
Clean the fans!
Turn off the led profile spotlight.
Using a small vacuum cleaner, suck the dust and “fur balls” out.
Do not use a can of co². That will just blast the dust and dirt everywhere!
The fans keep the LED cool and keep the electronics cool too.
Without the fan working efficiently and dust free, the fixtures will fail and that will be a lot more
costly than having someone
vacuum the fixtures on a regular basis.
How often should the fans be cleaned? It depends on where the fixtures are; in a very dusty
atmosphere once a week. So
check the fans on a regular basis, they may not need cleaned every week but a quick “visual
inspection” should be done.
The front lens should be cleaned so the light output is maintained.
The shutter blades sometimes require cleaning as well.
With the led profile spotlight turned off, use only a moist lint-free cloth. Never use alcohol or
solvents to clean the fixture.
Never spray anything onto the fixture at the front or in any place on the fixture.
10