The Singing Machine iSM-1028 N User manual

Instruction Manual
. the 0
sing ng
mac nine
iSM-1028 N
c
Please read before using this unit.
Pedestal CDG karaoke system with built-in
video camera, 7" TFT LCD color monitor, iPod
docking and AM/FM radio
The Singing Machine® is a registered trademark of The Singing Machine Co., Inc.

ENGLISH
WARNINGS
• TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
• THIS APPLIANCE SHOULD NOT BE EXPOSED TO OR PLACED NEAR, DRIPPING,
SPLASHING WATER OR OBJECTS FILLED WITH LIQUIDS (SUCH AS VASES.)
A
The lightning flash with
arrowhead symbol, within an
equilateral triangle, is
intended to alert the user to
the presence of unisulated
“dangerous voltage” within the
product's enclosure that may
be of sufficient magnitude to
constitute a risk of electric
shock to people.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER-SERVIC-ABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within
an equilateral triangle is
intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms orwhen unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Grounding or Polarization - This product may be equipped with a polarized alternating current line plug
(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This
is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
16. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable
operation of the product and to protect it from overheating, and these openings must not be blocked or
covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should not be placed in a built-in installation such as a bookcase or rack
unless properventilation is provided.
17. The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall
remain readily operable.
El

IMPORTANT SAFETY INSTRUCTIONS
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE
CAUTION: Invisible laser radiation when open and inter locks defeated. Avoid exposure to beam.
This class[B] digital apparatus complies with Canadian ICES-003.
CLASS 1 LASER PRODUCT
PRODUCTO LASERCLASE1
PRODUIT LASER DE CLASSE 1
LASER-PRODUKT DER KLASSE1
Class II equipment symbol
This symbol indicates that the unit
has a double insulation system.
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device , pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio TV technician for help.
E2
ENGLISH

INSTALLATION
STEP 2
2. Tighten a self tapping screw at the bottom of
the pedestal (middle).

INSTALLATION
STEP 3
3. Plug the RED connector and WHITE connector into
4. Tighten a self tapping screw at the control
panel (top).
E4
ENGLISH

ENGLISH
INSTALLATION INSTRUCTIONS FOR TOWER SPEAKERS
STEP 5
5. Attach the speaker into the stand according to
the installation illustration.
STEP 6
6. Tighten both screws on bottom of speaker.
E5

CONTROL LOCATIONS

ENGLISH
CONTROL LOCATIONS
FRONT VIEW
1. Adjustable Camera Lens
2. CD Door
3. iPod support
4. iPod adjustment knob
5. 7" TFT LCD Color screen
6. iPod Docking Station
7. Function Selector
8. Mic Flolder
9. COLOR control
10. VIDEO OUT Selector
11. BRIGHTNESS control
12. BALANCE control
13. MIC 1 Volume control
14. MASTER VOLUME
control
15. MIC 1 Jack
16. HEADPHONE Jack
17. MIC2 Jack
18. SKIP W4 (KEY/ECHO) -
button
19. PLAY/PAUSE button
20. MENU DOWN button
21. ON/OFF button
22. ON/OFF LED
23. TUNING knob
24. PROGRAM LED
25. LED Display
26. PLAY/PAUSE LED
27. CDG LED
28. REPEAT LED
29. BAND Selector
30. Monitor Selector
31. AUTO VOICE CONTROL
32. MIC 2 Volume control
33. PROGRAM button
34. REPEAT button
35. RANDOM button
36. KEY button
37. SKIP^Wj KEY/EC HO) +
button
38. ECHO button
39. MENU UP button
40. SELECT button
41. STOP/MENU button
E7

CONTROL LOCATIONS
ENGLISH

ENGLISH
MAKING THE CONNECTIONS
CONNECTING POWER
Plug the supplied AC power cord into the AC jack that is located on
the side panel of the product and plug the other end into a
standard AC socket.
CAUTION: The supplied AC power cord has a polarized plug that fits into
the wall outlet only one way. If the plug does not fit properly, turn
it over and try again. Do not force it.
CONNECTING TO YOUR TV OR VCR/DVD PLAYER
Your Singing Machine is designed to connect to your TV the same way you would connect most video
cameras, VCR/DVD players or video game consoles.
We have provided RCA cables to connect your unit to a TV, VCR/DVD player, video device or an external
audio/sound system. The RCA cables have three connections at each end (white and red are for left and
right audio connections and the yellow is for video connection).
Please follow the steps below to display CD+G lyrics on the TV screen:
(1) Locate the multi-colored RCAcables
(2) Connect video cable (yellow) to the VIDEO OUT on the side of the Singing Machine
(3) Connect the other end of the video cable (yellow) to the video input on your TV or VCR/DVD
Player
CONNECTING AVIDEO COMPONENT FOR INPUT
Please follow the steps below to display CDG lyrics on the Singing Machine’s monitor from another video
source:
(1) Locate the multi-colored RCAcables
(2) Connect video cable (yellow) to the VIDEO IN jack on the side of the Singing Machine
(3) Connect the other end of the video cable (yellow) to the video output on another video source
such as a VCR.
(4) Set the Function selector to AUX mode and the Monitor SelectortoAUX.
E9