The Singing Machine SML343BT User manual

TM
SML343BT
INSTRUCTION MANUAL / MANUAL DE INSTRUCCIONES
/ MODE D’EMPLOI
www.singingmachine.com
The Singing Machine® is a registered trademark of The Singing Machine Co., Inc.
The Singing Machine® es marca registrada de The Singing Machine Co., Inc.
The Singing Machine® est une marque déposée de The Singing Machine Co., Inc.

— E1 —
Warnings
Important Safety Information
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all Instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in
accordance with the Manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. When the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with a cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is
used, use caution when moving the cart/
apparatus combination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
15. WARNING: To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture. Do not place objects
filled with water, such as a vase, on the apparatus.
16. The AC mains plug is used as the power disconnect device
and it should remain readily accessible and operable during
intended use. In order to completely disconnect the apparatus
from power, the mains plug should be completely removed
from the AC outlet socket.
17. CAUTION: To reduce the risk of fire or explosion, do not expose
batteries to excessive heat such as sunshine, fire or other
heat sources.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The Caution marking is located on the bottom panel.
DANGEROUS VOLTAGE: The lightning flash with arrowhead
symbol within an equilateral triangle is intended to alert the
user to the presence of uninsulated dangerous voltage within
the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
ATTENTION: The exclamation point within an equilateral
triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying this product.
DRIPPING WARNING: This product shall not be exposed to dripping or
splashing, and no objects filled with liquids, such as vases, shall be placed
on the product.
VENTILATION WARNING: The normal ventilation of the product shall not
be impeded for intended use.
THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1,
SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURED.
Warnings:
• This CD player employs a laser light beam. Only a qualified service person
should remove the cover or attempt to service this device, due to
possible eye injury.
• The use of controls, adjustments, or procedures other than those
specified herein might result in hazardous radiation exposure.
• The apparatus shall be used in an open area.
CAUTION!
Invisible laser radiation when open and interlocks defeated. Avoid exposure
to beam.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
FCC WARNING: This equipment may generate or use radio frequency
energy. Changes or modifications to this equipment may cause harmful
interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
INDUSTRY CANADA NOTICE:
This device complies with Industry Canada Iicense-exempt RSS
standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The rating information is located at the back of the unit.

— E2 —
Included
What’s in the box.
Wired Microphone
Main Unit
Audio/Video Cables
AC Adapter
Manual Welcome Kit

— E3 —
Location of Controls (Front)
1. Handle
2. Disco Light button
3. ON/OFF indicator
4. ON/OFF button
5. Disco Lights
6. PLAY/PAUSE/PAIR
button
7. STOP button
8. SKIP  Button
9. SKIP  Button
10. PROGRAM/REPEAT
button
11. FUNCTION button
12. Display
13. Speaker
14. AUX IN jack
15. MIC 2 jack
16. MIC 1 jack
17. CD door
18. MASTER VOLUME
control
19. ECHO control
20. Auto Voice Control
21. BALANCE Control
22. MIC VOLUME control
23. CDG indicator
24. PLAY/PAUSE indicator
25. PROGRAM indicator
26. REPEAT indicator
u
v
w
x
y
U
V
W
X
ao
an
al
ak
at
am
ap
aq
ar
as
bt
bk
bl
bm
bp
bn
bo

— E4 —
Installation of Batteries
DC OPERATION
1. Slide the battery door in the direction of the arrow to reveal the battery compartment.
Insert eight (8) “C” size alkaline batteries (not included) as indicated on the diagram.
2. Replace cover tightly before operating.
CAUTIONS:
• Replace all batteries at the same time.
• Do not mix old batteries with new batteries.
Location of Controls (Rear)
Connection
27. VIDEO OUT jack
28. AUDIO OUT jack (R)
29. AUDIO OUT jack (L)
30. DC IN Jack
31. Battery Door
Battery Precautions
The precautions below should be followed when using batteries in this
device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as
indicated in the battery compartment. Reversed batteries may cause
damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline and
Carbon Zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the
batteries to prevent damage or injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged, they can
overheat and rupture. (Follow battery manufacturer’s directions.)
6. Rechargeable batteries are to be removed from the product before
being charged.
7. Rechargeable batteries are only to be charged under adult supervision.
8. Exhausted batteries are to be removed from the product.
9. Batteries shall not be exposed to excessive heat such as sunshine, fire
or the like.
bq
br
bs
ct
ck

— E5 —
Connection
Connecting the Microphone(s)
Microphones:
Connect a microphone into Mic jack 1 as
well as Mic jack 2 (when desired).
Note: Do not drop or tap the Mic as
damage to the Mic or speakers may occur.
Do not twirl the microphone cord as it will
cause damage to the encased wiring.
Connecting the Unit to a TV
VIDEO
INPUT
AUDIO
INPUT
R L
RCA cables
VIDEO OUT
(yellow)
AUDIO OUT
(white- L
red- R)
REAR VIEW OF TV
To output the video, lyrics and
audio to your TV, follow these
steps:
Connect the RCA video cable
(Yellow) to the VIDEO OUT jack
and the audio cables (White
and Red) to the AUDIO OUT
jacks located on the back of the
Singing Machine.
Connect the opposite end of
the RCA video cable (Yellow) to
the VIDEO IN jack and the audio
cables (White and Red) to the
AUDIO IN on your TV.
Notes:
• This unit can be used with or without a TV, but it is highly recommended to use a TV in
order to utilize all the features.
• Also refer to the TV’s User Guide.
• To see the lyrics on the screen, you must use a CD+G disc.
u
v

— E6 —
Connection
Connecting to AC Power
Connecting to AUX In Jack
Insert the AC power cord into an AC
outlet having 120V AC, 60Hz.
Note:
Make all connections before
connecting to AC power.
Connect an external device by using
an appropriate cable (3.5mm audio
cable not included) as shown.
Note:
See page E13 to select and use the
AUX In function.
YOUR SMARTPHONE,
DIGITAL PLAYER OR
MP3 PLAYER
AUDIO OUTPUT
/ HEADPHONE JACK
AUX IN
Disco Lights
1 Press the Disco Light button to switch on the lighting effect, press again to
switch off.
u

— E7 —
Operation
Playing a CDG
1 Connect the unit as described previously; if using a CD+G, it is
recommended to connect to a TV.
Press the power ON/OFF button to
turn the unit on.
2
Lift open the CD door and insert a CD
or a CD+G by gently pressing it on the
center spindle. Then close the CD door.
Note:
• What is a CD+G?
A CD+G (CD+Graphics) is the standard
format for most karaoke discs that will
display the words on the screen.
• Never place anything other than a CD
in the compartment, as foreign objects
can damage the unit.
• If no disc is inserted, “no” will appear on
the display.
• If connected to a TV and/or other
audio source, adjust the volume of
the external unit using its own volume
control.
3
Repeatedly press the FUNCTION
button to select the CDG mode; “--”
will appear when searching the disc and
then the total number of tracks will
appear. When a CDG disc is inserted,
the CDG indicator light will turn on.
4 Press the PLAY/PAUSE/PAIR button to start playback; if listening to a CD+G
file, the image and lyrics will appear on
the TV screen (if connected) and the
PLAY/PAUSE indicator light will turn on.
v
u
w
x

— E8 —
Operation
Playing a CDG (Continued)
5 Adjust the volume to a comfortable level using the MASTER VOLUME
control.
6
Connect microphone(s) and slide the
ON/OFF switch on the microphone to
the ON position.
7 Adjust the MIC VOLUME control as desired. Increasing this control
will increase the volume of both
microphones.
8
Rotate the ECHO control to add an
echo effect to your voice. Rotate
towards MAX to increase the echo
effect.
9
AUTO VOICE CONTROL can be
activated by rotating the AVC control.
The higher this control is set to, the
more the vocals on the multiplex
recording will be muted when the
singer starts to sing through the
microphone. When the singer stops
singing, the recorded vocals on the
multiplex recording will resume to
normal.
10 Rotate the BALANCE control clockwise to hear the music and
recorded vocals from a multiplex
recording or counterclockwise
to hear the music only from a
multiplex recording.
Note: To use the BALANCE control, a
CD+G disc must be used, otherwise it will
operate as a standard Balance control.
U
y
V
at
X
W

— E9 —
Operation
Playing a CDG (Continued)
11 SKIP: Advance or go back one track by pressing the Skip /Skip 
buttons.
12 REPEAT: During playback, press the PROGRAM/REPEAT button
once to repeatedly play the
selected song; the REPEAT indicator
will blink. Press the PROGRAM/
REPEAT button a second time to
repeatedly play the whole CD; the
REPEAT indicator will light solid.
Press it again to cancel Repeat
function, the REPEAT indicator
turns off.
13 PROGRAM: You can program up to 20 tracks on any disc for playback
in any desired order. While in the
Stop mode, press the PROGRAM/
REPEAT button; the PROGRAM
indicator will blink and “00” will
appear. Select the first track using
the Skip /Skip  buttons.
Press the PROGRAM/REPEAT
button again to confirm the entry.
After selecting the desired tracks
the display will show 01, 02, etc.
recognizing the tracks selected
have been programmed and the
PROGRAM indicator will illuminate
solid red. Repeat to set up to 20
tracks into memory. When done,
press the PLAY/PAUSE button to
start playback.
Note:
• Press the STOP button TWICE to stop
and clear the program.
ak
al
am

— E10 —
Operation
Playing a CDG (Continued)
14 PAUSE: During playback, if you wish to pause the disc momentarily,
press the PLAY/PAUSE/PAIR
button; the PLAY/PAUSE indicator
will blink. Press again to resume
normal playback.
15 Press the STOP button to stop playback.
16 Press the power ON/OFF button to turn the unit off.
ap
an
ao

— E11 —
Operation
Using a Bluetooth Device
1 Connect the unit as described
previously. Press the power ON/OFF
button to turn the unit on.
2 Repeatedly press the FUNCTION
button to select the Bluetooth mode;
“bt” will blink in the display as the unit
automatically searches for and pairs
a previously paired Bluetooth device
(if previously paired). If no previously
paired devices are present, connect as
shown in the next step.
Note: You can also press and hold the
PLAY/PAUSE/PAIR button to disconnect
any paired devices in order to pair another
device.
3 Turn on your device’s Bluetooth option
in settings to search for a discoverable
device with a Bluetooth signal. Select
“Singing Machine” from the device
results on the Bluetooth menu.
Note: Also refer to the user manual of your
Bluetooth device for detailed instructions.
4
“bt” will light solid in the display and a
successful pairing sound will be heard.
Notes:
• If your Bluetooth prompts you for a
passcode during the pairing process,
please enter “0000” to connect.
• On some Bluetooth devices, once pairing
is complete, select your Bluetooth device
as “Use as Audio Device” or similar.
• If connection is lost after successful
pairing, check to make sure the distance
between speaker and Bluetooth-enabled
device does not exceed 30 feet/10
meters.
•“Bluetooth” will blink on TV screen,
and will stop blinking after successful
connection.
3
u
v

— E12 —
Operation
Using a Bluetooth Device (Continued)
5 To control your Bluetooth device from this unit, press the PLAY/PAUSE/
PAIR button to start playback. Press
the PLAY/PAUSE/PAIR button
during playback to pause the song.
6
Adjust the volume to a comfortable
level using the MASTER VOLUME
control on this unit as well as the
volume on your Bluetooth device.
7
Connect microphone(s) and slide the
ON/OFF switch on the microphone to
the ON position.
8
Adjust the MIC VOLUME control
as desired. Increasing this control
will increase the volume of both
microphones.
9 Rotate the ECHO control to add an echo effect to your voice. Rotate
towards MAX to increase the echo
effect.
10 Adjust the balance between the speakers using the BALANCE
control.
11 SKIP: Advance or go back one track by pressing the Skip /Skip 
buttons.
12 Press the power ON/OFF button to turn the unit off.
V
yU
at
X
al
ak
W

— E13 —
y
Operation
Using the AUX IN Jack
1 Connect the unit as described previously. Press the power ON/OFF
button to turn the unit on.
2
Repeatedly press the FUNCTION
button to select the AUX IN mode;
“AU” will appear on the display.
3
Connect the external unit to the
AUX IN Jack on the front of this unit.
Connecting an external unit will allow
the audio to be played through your
Singing Machine.
Notes:
• It is highly recommended to set the
volume on the auxiliary unit to 1/3 or
lower to avoid distortion.
• Skipping files/tracks is not possible on
this unit when using an external device.
4 Adjust the volume using the MASTER VOLUME control on this unit or your
external device’s volume control.
5 Connect microphone(s) and slide the ON/OFF switch on the microphone to
the ON position.
x
u
v
w

— E14 —
Operation
Using the AUX IN Jack (Continued)
6 Adjust the MIC VOLUME control as desired. Increasing this control
will increase the volume of both
microphones.
7 Rotate the ECHO control to add an echo effect to your voice. Rotate
towards MAX to increase the echo
effect.
8 Adjust the balance between the speakers using the BALANCE control.
9 Press the power ON/OFF button to turn the unit off.
W
V
X
U

— E15 —
Troubleshooting Guide
Should this unit exhibit a problem, check the following before seeking service:
No Power
• Power is not on; press the power ON/OFF button to turn power on.
• Confirm that the AC adapter is connected securely to the back of the unit.
• Connect the unit to a different outlet.
No Sound – General
• Master Volume is set to minimum; raise volume.
• Correct Function was not selected; select using the FUNCTION button.
• If using an external device, raise the volume.
No Sound – If connected to a TV
• Volume on the TV is muted or too low.
• Correct source (usually AV) was not selected on the TV’s menu.
Lyrics do not appear on the TV screen
• If connected to a TV, Video plug is not connected properly; see page E5.
• If connected to a TV, select the correct source on the TV (usually AV).
• The file/track being played is not a track recording with lyrics. These are the only files
that allow you to view the lyrics on the TV screen.
• Nothing will appear on the TV screen when using AUX In or Bluetooth.
No sound from the microphone
• Make sure the microphone is firmly connected to the MIC 1 or MIC 2 jack.
• Make sure the ON/OFF switch on the microphone is set to the ON position.
• Make sure the MIC VOLUME setting is not set too low.
• MASTER VOLUME is set to minimum; raise volume.
• Adjust the ECHO control past the mid point on the Singing Machine.
The Bluetooth device cannot be paired or connected with the unit
• You have not activated the Bluetooth function of your device; see page E11 or refer to
the Bluetooth device user’s manual.
• The system is not in pairing mode; press and hold the PLAY/PAUSE/PAIR button to
restart pairing.
The Music is not available on the unit after successfully connecting the Bluetooth
• Ensure your Bluetooth device can support the A2DP Bluetooth profile.
• The volume on the external Bluetooth device is set to low or muted; raise as desired.

— E16 —
Specifications
AUDIO
OUTPUT POWER (MAXIMUM)................................................................................ 3.5 Watts (RMS)
OUTPUT IMPEDANCE ...............................................................................................................30 Ohms
CD PLAYER SECTION
FREQUENCY RESPONSE ............................................................................................100 Hz - 20 kHz
SIGNAL-TO-NOISE RATIO ............................................................................................................. 50 dB
NUMBER OF PROGRAMS ..................................................20 Step Random Access Programming
SAMPLING SYSTEM ........................................................................................8 Times Over Sampling
BLUETOOTH
Bluetooth Version ....................................................................................................................V2.1+EDR
Working Distance ..........................................Up to 30 feet/10 meters measured in open space
AUX IN SECTION .......................................................................... 3.5 mm Stereo Headphone Jack
MICROPHONE .................. -74 db 600 Ohm Impedance with 6.3 mm Dynamic Microphone
POWER SECTION ..........DC 5.8V 1.5A (8 x “C” Batteries) (Batteries not included)
DIMENSIONS (HxWxD) .......................... 13.3 x 12.0 x 6.1 inches / 33.8 x 30.5 x 15.5 cm
WEIGHT ........................................................................................................................4.0 lbs / 1.82 kgs
Specifications are subject to change without notice.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks and logos by The Singing Machine Company, Inc. is under
license. Other trademarks and trade names are those of their respective owners.

— S1 —
Advertencias
Información importante sobre seguridad
1. Lea estas instrucciones.
2. Conserve estas instrucciones.
3. Preste atención a todas las advertencias.
4. Siga todas las instrucciones.
5. No utilice este artefacto cerca del agua.
6. Límpielo únicamente con un paño seco.
7. No obstruya las aberturas para ventilación. Instálelo de acuerdo con
las instrucciones del fabricante.
8. No instale cerca de fuentes de calor, como radiadores, rejillas de
calefacción, estufas u otros aparatos (incluso amplificadores) que
produzcan calor.
9. No desafíe el fin de seguridad del enchufe polarizado o de conexión
a tierra. Un enchufe polarizado tiene dos clavijas y una es más
ancha que la otra. El enchufe de conexión a tierra tiene dos clavijas,
y una tercera punta a tierra. La clavija ancha o la tercera punta se
suministran para su seguridad. Si el enchufe suministrado no coincide
con su tomacorriente, consulte con un electricista para reemplazar el
tomacorriente obsoleto.
10. Evite pisar o apretar el cable de alimentación, especialmente en los
enchufes, tomacorrientes y en el punto por donde salen del artefacto.
11. Utilice sólo los complementos y accesorios especificados por el
fabricante.
12. Utilice la unidad sólo con el carro, soporte, trípode, repisa o mesa
recomendados por el fabricante, o que se
vendan junto con el producto Cuando se
utiliza un carro, tenga cuidado cuando mueva
el carro y artefacto junto a para evitar lesiones
producidas por la caída del producto.
13. Desenchufe este artefacto durante las
tormentas eléctricas o cuando no se lo utilice
durante períodos prolongados.
14. Derive todas las reparaciones al personal de
reparaciones calificado. Es necesario reparar el artefacto cuando se
encuentra dañado; por ejemplo, cuando el cable de suministro de
energía o el enchufe están dañados, cuando se derrama líquido sobre
la unidad o caen objetos dentro del mismo, cuando el producto ha
estado expuesto a la lluvia o a la humedad, cuando no funciona con
normalidad o cuando se ha caído.
15. ADVERTENCIA: Para reducir el riesgo de incendio o descarga eléctrica,
no exponga este artefacto a la lluvia o la humedad. No coloque
objetos llenos de agua, como jarrones, sobre el aparato.
16. El enchufe de conexión de CA se utiliza como dispositivo de
desconexión eléctrica y deberá estar siempre accesible y en
funcionamiento durante el uso previsto. Para desconectar
completamente el aparato de la electricidad, el enchufe de conexión
deberá quitarse por completo del tomacorriente de CA.
17. PRECAUCIÓN: Para reducir el riesgo de incendio o explosión no
exponga las baterías al calor excesivo, como al rayo del sol, fuego u
otras fuentes de calor
ADVERTENCIA SOBRE EL CARRO
PORTÁTIL
(símbolo provisto por RETAC)
ADVERTENCIA: PARA EVITAR INCENDIOS O PELIGROS DE DESCARGA,
NO EXPONGA ESTA UNIDAD A LA LLUVIA O HUMEDAD.
VISO DE LA FCC: Este equipo puede generar o usar energía de radio frecuencia. Los
cambios o modificaciones realizados en el aparato pueden provocar interferencia
perjudicial, a menos que dichas modificaciones estén autorizadas en el manual de
instrucciones. El usuario puede perder toda autoridad para operar el equipo si realiza
cambios o modificaciones sin autorización.
Este aparato cumple con la parte 15 de las Normas de la FCC. El funcionamiento
está sujeto a las dos condiciones que figuran a continuación: (1) Es probable que no
cause interferencia perjudicial y (2) deberá aceptar cualquier interferencia recibida,
incluyendo la interferencia que pueda llegar a causar un funcionamiento indeseado.
NOTA: Este equipo fue probado y se concluyó que cumple con los límites
establecidos para los dispositivos digitales Clase B, de acuerdo con el Apartado
15 de las normas de la FCC. Estos límites fueron pensados para proporcionar
protección razonable ante la interferencia perjudicial en una instalación residencial.
Este equipo genera, usa y puede emitir energía de radio frecuencia y, si no se lo
instala y utiliza de conformidad con las instrucciones, puede causar interferencia
perjudicial a las comunicaciones radiales. No obstante, no existe ninguna garantía
de que no se produzca interferencia en una instalación en particular. Si este equipo
provoca interferencia perjudicial a la recepción de radio o televisión, lo cual puede
determinarse apagando y encendiendo el equipo, el usuario puede intentar corregir
la interferencia de alguna/s de las siguientes maneras:
• Reoriente la antena receptora o ubíquela en otro lugar.
• Aumente la distancia entre el equipo y el receptor.
• Conecte el equipo a un tomacorriente de un circuito distinto al que está conectado
el receptor.
• Consulte al distribuidor o a un técnico experimentado de radio y televisión para
que lo asesore.
• La información de clasificación está ubicada en la parte inferior de la unidad.
AVISO A LA INDUSTRIA CANADIENSE:
Este dispositivo cumple con los estándares RSS de exentos de licencia de la industria
canadiense.
La operación está sujeta a las dos condiciones siguientes:
1. este dispositivo no puede causar interferencia, y
2. este dispositivo debe aceptar cualquier interferencia, incluyendo la interferencia
que puede causar un funcionamiento indeseado del dispositivo.
PRECAUCIÓN: PARA REDUCIR EL RIESGO DE DESCARGAS ELÉCTRICAS, NO
QUITE LA CUBIERTA (NI LA TAPA POSTERIOR) NO HAY PIEZAS REPARABLES
POR EL USUARIO DENTRO. DERIVE LAS REPARACIONES A PERSONAL DE
SERVICIO CALIFICADO.
Las marcas de Precaución se ubican en el panel inferior.
TENSIÓN PELIGROSA: La luz intermitente con símbolo de
flecha dentro de un triángulo pretende alertar al usuario de la
presencia de tensión peligrosa no aislada, dentro del paquete
del producto, que puede ser de magnitud suficiente para
constituir un riesgo de descarga eléctrica para las personas.
ATENCIÓN: El signo de exclamación dentro de un triángulo
pretende alertar al usuario de la presencia de instrucciones
importantes de operación y mantenimiento (reparaciones) en
el material que acompaña a este producto.
ADVERTENCIA DE GOTEO: Este producto no se podrá exponer a goteo
o salpicaduras, y no se colocará ningún objeto lleno con líquidos, como
jarrones, encima del producto.
ADVERTENCIA DE VENTILACIÓN: La ventilación normal del producto no se
bloqueará si se le da el uso previsto.
Este producto cumple con las normas DHHS 21 CFR del capítulo 1,
subcapítulo J que aplican desde la fecha de fabricación.
Advertencias:
• Este reproductor de CD utiliza un haz de luz láser. Solo la persona de
reparaciones calificada es quien puede retirar la cubierta y reparar este
dispositivo debido a posibles lesiones en la vista.
• El uso de controles, ajustes o la realización de procedimientos que no sean
los especificados en el presente pueden producir exposición a radiación
peligrosa.
• El artefacto deberá utilizarse en un espacio abierto.
PRECAUCIÓN!
Si la caja se abre o el dispositivo de seguridad se destruye, puede producirse
la emisión invisible de radiación láser. Evite la exposición al haz de luz.
PRECAUCIÓN
RIESGO DE DESCARGA ELÉCTRICA
NO ABRIR

— S2 —
Se incluyen
Asegúrese de que estén incluidos los siguientes elementos.
Micrófono con cable
Unidad principal
Cables de Audio/Video
Adaptador de CA
Manual Kit de bienvenida

— S3 —
Ubicación de controles (Delantero)
1. Manija
2. Botón Luz de disco
(Disco Light)
3. Indicador de
ENCENDIDO/APAGADO
(ON/OFF)
4. Botón de ENCENDIDO/
APAGADO (ON/OFF)
5. Luces de disco
6. Botón REPRODUCIR/
PAUSAR/SINCRONIZAR
(PLAY/PAUSE/PAIR)
7. Botón DETENER (STOP)
8. Botón SALTO  (SKIP)
9. Botón SALTO  (SKIP)
10. Botón PROGRAMAR/
REPETIR (PROGRAM/
REPEAT)
11. Botón de FUNCIÓN
(FUNCTION)
12. Pantalla
13. Altavoz
14. Conector de ENTRADA
AUXILIAR (AUX IN)
15. Conector para
MICRÓFONO 2 (MIC 2)
16. Conector para
MICRÓFONO 1 (MIC 1)
17. Tapa del CD
18. Control de VOLUMEN
PRINCIPAL (MASTER
VOLUME)
19. Control de ECO (ECHO)
20. Control de voz
automático (Auto
Voice)
21. Control de BALANCE
22. Control de VOLUMEN
DEL MICRÓFONO (MIC
VOLUME)
23. Indicador CDG
24. Indicador de
REPRODUCIR/PAUSAR
(PLAY/PAUSE)
25. Indicador de
PROGRAMA
(PROGRAM)
26. Indicador de REPETIR
(REPEAT)
u
v
w
x
y
U
V
W
X
ao
an
al
ak
at
am
ap
aq
ar
as
bt
bk
bl
bm
bp
bn
bo