The Singing Machine BRATZ SMB-664 User manual

SMB-664 Please read before using this unit.
Lea antes de usar esa unidad.
Veuillez lire avant d'utiliser cet appareil.
Compact Disc + Graphics
with Built-In Disco Light
Karaoke Center
Instruction Manual
Manual De Instrucción
Manuel D'instruction
CD + Diseños con
Centro de Karaoké con
Luces de DiscotecA
Compact Disque + Graphiques
avec Centre de Lumière Disco
Karaokê encastré

WARNINGS
E1
ENGLISH
WARNING:TO REDUCE THE RISK OF
FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION: TO PREVENT THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
OR BACK. NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol is intended to alert you
to the presence of uninsulated
dangerous voltage within the
product's enclosure that might be of
sufficient magnitude to constitute a
risk of electric shock. Do not open
the product's case.
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature
accompanying this product.
DRIPPING WARNING
VENTILATION WARNING
The product shall not be exposed to dripping or
splashing and that no objects filled with liquids,
such as vases, shall be placed on the product.
The normal ventilation of the product shall not
be impeded for intended use.
COMPLIES WITH DHHS RADIATION
PERFORMANCE STANDARDS, 21 CFR
SUB. CHAPTERJ. THIS DEVICE
COMPLIES WITH PART 15 OF THE FCC
RULES, OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS
DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE
MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED
OPERATION.
CERTIFICATION:
THIS PRODUCT COMPLIES WITH 21 CFR
CHAPTER 1, SUBCHAPTER J OF DHHS
REGULATIONS.
COMPLIES WITH THE LIMITS FOR A
CLASS B DIGITAL DEVICE, PURSUANT
TO PART 15 OF THE FCC RULES.
SERVICEMAN CAUTION:
IMPORTANT
This class[B] digital apparatus complies
with Canadian ICES-003.
SEE WARNING NOTICE ON THE INSIDE
OF BACK COVER.
Since CD circuitry may cause interference to
other radio tuners nearby, switch this unit off
when not in use or move it away from the
affected radio tuner.
This CD player is made and tested to meet
exacting safety standards. It meets FCC
requirements and complies with safety
performance standards of the U.S.
Department of Health and Human Services.
This CD player employs a laser light beam.
Only a qualified service person should
remove the cover or attempt to service this
device, due to possible eye injury.
The use of controls, adjustments, or
procedures other than those specified
herein might result in hazardous radiation
exposure.
This compact disc player is classified as a
CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT label is
located on anel.
Invisible laser radiation when open and inter
locks defeated.Avoid exposure to beam.
Warnings:
CAUTION!
!
!
CAUTION
!The apparatus shall be used in an open
area.
the bottom p
The CAUTION marking is located on anel.the bottom p

IMPORTANT SAFETY INSTRUCTIONS
1. Read Instructions
2. Retain Instructions
3. Heed Warnings
4 Follow instructions
5. Cleaning
6. Attachments
7. Water and Moisture
8. Accessories
9.
10. Ventilation
11. Power Sources
-All the safety and operating instructions should be read before the product is operated.
- The safety and operating instructions should be retained for future reference.
-All warnings on the product and in the operating instructions should be adhered to.
. -All operating and use instructions should be followed.
- Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning the exterior only. Do NOT attempt to clean the inside.
- Do not use attachments not recommended by the product manufacturer as they may cause
hazards.
- Do not use this product near water - for example, near a bath tub, wash bowl, kitchen
sink, or laundry tub; in a wet basement, or near a swimming pool, and the like.
- Do not place this product on an unstable cart, stand tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the
product should follow the manufacturer's instructions, and should use a mounting accessory recommended by
the manufacturer.
Aproduct and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces
may cause the appliance and cart combination to overturn.
- Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of
the product and to protect it from overheating, and these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is
provided.
- This product should be operated only from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your home, consult your product dealer or local power
company. For products intended to operate from battery power, or other sources, refer to the operating
instruction.
12. Grounding or Polarization
Alternate Warnings
13. Power-Cord Protection
14. Protective Attachment Plug
- This product may be equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to
fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized
plug.
- This product may be equipped with a three-wire grounding-type plug, a plug having a
third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the grounding-type plug.
- Power supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
- The product is equipped with an attachment plug having overload protection.
This is a safety feature. See Instruction Manual for replacement or resetting of protective device. If
replacement of the plug is required, be sure the service technician has used a replacement plug specified by
the manufacturer that has the same overload protection as the original plug.
E2
ENGLISH

IMPORTANT SAFETY INSTRUCTIONS
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
S2898A
15. OutdoorAntenna Grounding - If an outside antenna is connected to the receiver, be sure the antenna system
is grounded so as to provide some protection against voltage surges and built-up static charges.Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the
grounding electrode. See figure:
16. Lightning
17. Power Lines
18. Overloading
19. Object and Liquid Entry
20. Servicing
21. Damage Requiring Service
22. Replacement Parts
23. Safety Check
24. Wall or Ceiling Mounting
25. Heat
- For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This
will prevent damage to the product due to lightning and power-line surges.
-An outside antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact
with them might be fatal.
- Do not overload wall outlets, extension cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
- Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of
any kind on the product.
- Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
- Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified technician to restore the product to
its normal operation.
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this indicates a need for service.
- When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
- Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks to determine that the product is in proper operating condition.
- The product should be mounted to a wall or ceiling only as recommended by the
manufacturer.
- The product should be situated away from heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
E3
ENGLISH

E4
ENGLISH
Your with built-in Disco Light Karaoke Center will provide you with
many years of fun and entertainment. It can let you be the “star” as you sing along with your
favorite recordings and hear your voice with the music through the system’s speaker.
This Karaoke Center is easy to use, yet full of features with a compact design. After just a few
simple instructions, you will become an expert. Before you use your unit, please glance through
this manual to familiarize yourself with all the features available and the sections of the manual
that describe their operation. Next, go to the section for the specific operation you wish to
perform.
For your easy reference, listed here are some of the main features of this Karaoke Center:
- displays the lyrics with the tempo of music when playing CD+G discs.
- lets you sing along with different disco lighting modes.
- lets you replace the original singer's voice with your own voice when any
prerecorded, multiplex karaoke disc or tape is played. To activate, just rotate Mic Volume to a
comfortable listening level, and Auto Voice Control for the best balance between playback and
microphone levels.
- lets you adjust the balance between the prerecorded original singer's voice
and the music if you use a multiplex karaoke disc.
- lets you add an echo to enrich your voice for a concert hall effect.
- lets you turn the volume control clockwise or counter-clockwise until
desired volume level is obtained.
- lets you share the music with your family or friends.
- lets you connect another audio output component, such as an
equalizer/booster or a PAsystem.
Compact Disc + Graphics
- lets you connect the headphones instead of using the built-in speaker.
Lyrics on TV screen
Disco Light
Auto Voice Control
Balance Control
Echo Control
Master Volume Control
Built-In Speaker
Auxiliary Output Jacks
Headphone Jack
INTRODUCTION

SMB-664

REAR VIEW
31. AUX IN Jack (L)
32. AUX OUT Jack (L)
33. VIDEO OUT Jack
34. AUX OUT Jack (R)
35. AUX IN Jack (R)
36. AC Power Cord
E6
ENGLISH
CONTROL LOCATIONS
31
32
33
34
35
36

MAKING THE CONNECTIONS
CONNECTING POWER
CAUTION:
CONNECTING TO YOUR HEADPHONE
You can power the system from a standardAC outlet by using the supplied power cord.
The suppliedAC power cord has a polarized plug that fits into the wall outlet only one
way. If the plug does not fit properly, turn it over and try again. Do not force it.
A Headphone Jack is provided for using headphones instead of the built-in speaker.
(Headphones are sold separately.)
CONNECTING TO YOUR TV
VIDEO CONNECTION
The Singing Machine provides a patch cord to give you the option of connecting your unit to an
external audio/sound system and video device. The patch cord has three RCA jacks at each
end. White and Red are for left and right audio connections and the yellow is for connecting the
video.
Make sure that you have a CDG disc in the Singing Machine and playing when you are making
this connection. You will know you have the proper settings on your TV or VCR as soon as you
see the Singing Machine logo or lyrics on the screen!
Please follow the steps below to display CDG lyrics on the TV screen:
(1) Locate the multi-colored patch cords.
(2) Connect video cable (yellow) to the Video Out of the back of the Singing Machine.
(3) Connect the other end of the video cable (yellow) to the Video Input on your TV or
VCR.
E7
ENGLISHENGLISH
R
L
OUT IN
AUX
VIDEO
OUT VIDEO
INPUT
VIDEO INPUT
(Yellow Jack)
REAR VIEW OF
SINGING MACHINE REAR VIEW OF TV
VIDEO OUTPUT
(Yellow Jack)

If your television does not have the required Video Input, you will need an RF Modulator (Radio
Frequency Modulator), which connects through your TV Antenna or cable line and serves as
Video Input.
An RF Modulator can be purchased at almost any consumer electronics retailer. If you are
connecting the video from the Singing Machine to either a television or a VCR video input jack,
you must specify the source the TV or VCR is to display. Your TV or VCR user guide can tell you
how to display the video signal from the ‘Video In’jack.
If you don’t have the manual for your TV or VCR we suggest calling the TV or VCR
manufacturer’s customer service department. Only the manufacturer will be able to tell you very
quickly how to configure your TV or VCR to display the video signal coming from the ‘Video
Input’jack.
Note: Some projection TV sets do not display the standard blue background used on most
CDGs properly. If the background color is inconsistent or flashing, please try connecting your
Singing Machine to a standard tube television.
(1)
(2)
D
COMMON WAYS TO CONFIGURE YOUR TV OR VCR
Your Singing Machine is designed to connect to your TV the same way you would connect a
video camera, VCR or video game. The Singing Machine is constantly sending the video and
audio signals to the 'Video Out' and 'AUX OUT' jacks whenever you play a CDG. So, load a CDG
into your Singing Machine before you start making these connections. You will see lyrics on the
TV screen as soon as you get the setup completed correctly.
We refer to TV/VCR because manufacturers use very similar ways to connect TVs and VCRs
and you can connect your Singing Machine to a TV, VCR or satellite system. The setup of your
TV/VCR is the most difficult part of making the connection for displaying your Singing Machine
lyrics. In most homes, the TV has either a cable connected or antennae in use. Once you
connect your Singing Machine to the TV/VCR, you must 'tell' your TV/VCR to display the input
from the Singing Machine instead of the usual input from the cable or antennae.
Check your TV/VCR user manual for the easiest way to setup your particular entertainment
system. If you don't have your manual you can always call your TV/VCR manufacturer for that
information or try hitting their website for online assistance. We've listed below the most
common ways of setting up a TV/VCR:
In the setup menu for configuring the TV/VCR there may be an option on 'Input Selection'
where you may choose between 'Cable/Ant.', 'Video 1', or 'Video 2' etc. as the input source.
Try looking for a 'Video' channel between the highest channel and the lowest channel on
your TV or VCR. (i.e. Between 99 and 2 may be 'VIDEO' or 'INPUT' or 'GAME')
(3) Look for a button on the remote control for the TV/VCR you are connecting to that says
'VIDEO', 'VIDEO 1', 'Game', 'AUX', 'EXT', 'LINE1', 'LINE-IN' or occasionally the 'VCR'
button will display the Video input source.
MAKING THE CONNECTIONS
E8
ENGLISHENGLISH

AUDIO CONNECTION
FOR CONNECTINGAN AUDIO COMPONENT FOR OUTPUT
Connect the unit to your TV or home stereo system using the White and Red connections on the
supplied patch cord. Plug the white end of the patch cord into the white AUX OUT jack on the
unit. Plug the red end of the patch cord into the redAUX OUT jack on unit. Now connect the other
end of the cable’s white (left channel) and red (right channel) plugs to your TV or home stereo
system’s ‘AUDIO IN’or ‘AUX IN’jacks.
To connect an audio component (such as a power amplifier or PA system amplifier) so you can
hear the system’s music & vocal through it, plug the audio component into theAUX OUTjacks.
MAKING THE CONNECTIONS
AUDIO
INPUT
RL
AUX OUTPUT
L
(White Jack)
REAR VIEW OF
SINGING MACHINE
R
L
OUT IN
AUX
ANOTHER AUDIO
COMPONENT
AUDIO INPUT
L
(White Jack)
AUDIO INPUT
R
(Red Jack)
AUX OUTPUT
R
(Red Jack)
AUDIO
INPUT
RL
AUX OUTPUT
L
(White Jack)
REAR VIEW OF
SINGING MACHINE
R
L
OUT IN
AUX
REAR VIEW OF TV
AUDIO INPUT
L
(White Jack)
AUDIO INPUT
R
(Red Jack)
AUX OUTPUT
R
(Red Jack)
E9
ENGLISH