THE STANDING DESK LÜFTEN User manual

FOR VIDEO INSTALL INSTRUCTIONS GO TO TheStandingDesk.com/install
THE LÜFTEN
TWIN COLUMN TABLE
ASSEMBLY INSTRUCTIONS THE LÜFTEN
TWIN COLUMN TABLE
ASSEMBLY INSTRUCTIONS
FOR VIDEO INSTALL INSTRUCTIONS GO TO TheStandingDesk.com/install 1 / 44 / 4
INCLUDED HARDWARE PACKAGE
INCLUDED TOOLS PLEASE REVIEW these instructions completely
and verify all parts are included in this package
before beginning assembly. Do not discard
the packaging until satised that the product
operates properly. Assembly and operation
of this desk must be in accordance with these
assembly instructions to avoid the risk of injury.
Keep these Assembly and Operation Instructions
near the assembly for reference.
REQUIRED TOOLS
Boden Cord Clip (1) Glides (4) OPTIONAL
Castors (4)
Socket Head
Cap Screw (8)
Flat Head
Cap Screw (8)
1/2” Wood
Screw (5)
1” Wood
Screw (8)
m6
Allen Wrench
m8
Allen Wrench
#2 Phillips Head
Screwdriver
1/2” Wrench
“Note” Ideal weight capacity range for the Luften desk is 15-35lbs with a standard 350N spring. The table support is
solely intended to serve the purpose of ergonomic adjustments for your desk in accordance with the weights and measurements
given in these instructions. Any usage other than that mentioned in this document is inappropriate; the manufacturer disclaims
liability for any resulting damages. In such cases the user bears the full risk. The manufacturer cannot be held responsible for
any losses or damages resulting from unauthorized modications of this desk.
5
Glides (4)
OPTIONAL
Castors (4)
1/2” Wrench
OPERATING INSTRUCTIONS
To adjust the height of the table, squeeze the release handle and allow table to move up or push down
on table top to lower. To cause more or less tension when lifting and lowering the table, use a wrench to
tighten or loosen the ADJUSTMENT BARREL attached to the end of the handle.
CAUTION: Brace the top with free hand when moving the table up and down to control movement.
• Twist in the GLIDES
or the (OPTIONAL)
CASTORS into the
holes on the bottom
of the base.
• If not secure
enough, tighten with
WRENCH.
Adjustment Barrel
Adjustment Barrel
For proper cleaning instructions go to
TheStandingDesk.com/clean

FOR VIDEO INSTALL INSTRUCTIONS GO TO TheStandingDesk.com/install
THE LÜFTEN
TWIN COLUMN TABLE
ASSEMBLY INSTRUCTIONS THE LÜFTEN
TWIN COLUMN TABLE
ASSEMBLY INSTRUCTIONS
FOR VIDEO INSTALL INSTRUCTIONS GO TO TheStandingDesk.com/install
2 / 4 3 / 4
3
4
Hex Socket Cap Screw (8)
M8 Allen Wrench
1/2” Wood Screw
#2 Phillips Head Screwdriver
Boden Cord Clip (1)
1
2
Flat Head Cap Screw (8)
M6 Allen Wrench
1” Wood Screw (8)
#2 Phillips Head Screwdriver
• Remove traveling screws from both columns.
CAUTION: When screw is removed from the
column without the Boden cord attached, the
column will move in and out freely.
• Attach the top plate to the column containing
the Boden cord with the FLAT HEAD CAP
SCREWS and the M6 ALLEN WRENCH.
• Pull the remaining column up to the top plate
and again secure it with the FLAT HEAD CAP
SCREWS.
• Flip over the
columns and top
plate and align
the holes on the
top plate with the
pilot holes on the
worksurface.
• Attach the top plate
to the worksurface
with the 1” WOOD
SCREWS and
PHILLIPS HEAD
SCREWDRIVER.
• Slip the base over
both the columns
and attach the base
with the SOCKET
HEAD CAP SCREW
and the M8 ALLEN
WRENCH.
• Attach the handle
to the worksurface
with the 1/2” WOOD
SCREWS and a
PHILLIPS HEAD
SCREWDRIVER. Slip
the BODEN CORD
CLIP over the Boden
cord and secure with
the last 1/2” WOOD
SCREW to the
remaining pilot hole.
SEAM SIDE