THE WORLD MODELS PAULISTINHA P-56 EP User manual

PAULISTINHA P-56
Wing Span
Wing Area
Flying Weight
Fuselage Length
71.0 in / 1800 mm
698 sq in / 45.0 sq dm
5.5 lbs / 2500 g
47.0 in / 1200 mm
Specifications
Requires: 0.40-0.46 cu. in. displacement 2-stroke
0.52-0.56 cu. in. displacement 4-stroke
4 - channel radio w/ 5 standard servos
INSTRUCTION MANUAL
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY(ARF)SERIES
MADE IN CHINA
* Specifications are subject to change without notice.*
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
The World Models
Manufacturing Co., Ltd.
www.theworldmodels.com
A321PO26781107

BEFORE YOU BEGIN
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P.1
P.2
P.3 - 11
P.11
Read through the manual before you begin, so you will have an overall idea of what to do.
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CAor Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for
warranty replacement. The manufacturer will replace any defective parts, but will not extend
to the parts that are good before gluing to defective parts during assembly. Warranty will
not cover any parts modified by customer.
Symbols used throughout this instruction manual comprise of the following :-
1
2
3
P.1
3mm
Do not overlook this symbol!
Cut off shaded portion.
Peel off shaded portion
covering film.
Pay close attention here!
Pierce the shaded portion
covering film.
Must be purchased separately!
Drill holes with the specified
diameter (here: 3mm).
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Apply epoxy glue.
Apply thread locker
Warning!
PAULISTINHAP-56
A321PO26781107

Parts List
P.2
COVERING: --
LIGHTEX SGX 310 RED
LIGHTEX SGX 201 BLACK
TOUGHLON STL 204 CREAM
1. MAIN WING -- 1 pair
2. SCREW PWA2x8mm -- 8 pcs
PLYWOOD 2x52x80mm (For Aileron Servo) -- 1 pair
BALSA 8x18x21mm (For Aileron Servo) -- 4 pcs
3. SCREW PB2x18mm -- 6 pcs
FUEL TUBE Ø6x5mm -- 4 pcs
CLEVIS PL4112103 -- 2 pcs
STRAPER PL4112102 -- 2 pcs
TRI-HORN M3x14mm (S) -- 2 sets
PUSHROD Ø1.8x100mm w/ Threads(For Aileron) -- 2 pcs
4. PLYWOOD 2x30x120mm (Wing Protection) -- 1 pc.
WING TUBE Ø9.6x267mm -- 1 pc.
5. SOCKET HEAD SCREW M3x18mm -- 4 pcs
SCREW PWA2x8mm -- 4 pcs
SCREW PM2x12mm -- 4 pcs
M2 NUT -- 4 pcs
COPPER CLIPPER 0.5x8x10mm -- 8 pcs
WASHER d2xD5mm -- 8 pcs
MAIN WING STRUTS -- 1 pair
WING STRUT WIRE Ø1.8x110x104mm -- 2 pcs
6. FUSELAGE -- 1 pc.
VERTICAL FIN & RUDDER -- 1 set
STABILIZER & ELEVATOR -- 1 set
7. SCREW PA3x12mm -- 2 pcs
TAIL LANDING GEAR -- 1 set
TAIL WHEEL Ø25mm -- 1 pc.
COLLAR Ø2.1mm w/ set screw -- 1 set
SCREW PM2x12mm -- 1 pc.
M2 NUT -- 1 pc.
ALUMINUM PLATE 0.5mm -- 1 pc.
8. ENGINE MOUNT PL5111050 -- 1 set
SOCKET HEAD SCREW M4x25mm -- 4 pcs
WASHER d4.5xD9mm -- 4 pcs
9. SOCKET HEAD SCREW M3x25mm -- 4 pcs
WASHER d3xD7mm -- 8 pcs
M3 NUT -- 8 pcs
THROTTLE PUSH WIRE Ø1.2x340mm -- 1 pc.
PLASTIC TUBE d2xD3x250mm -- 1 pc.
10. FUEL TANK 260cc -- 1 set
CABLE TIE(For Fuel Tank) 1.5x5x400mm -- 1 pc.
DOUBLE-SIDED TAPE 40x100mm -- 1pc.
11. SOCKET HEAD SCREW M3x16mm -- 2 pcs
SCREW PA3x8mm -- 6 pcs
WASHER d3xD7mm -- 2 pcs
M3 NUT -- 2 pcs
ALUMINUM PLATE 2mm -- 2 pcs
MAIN LANDING GEAR -- 1 set
MOUNTING PLATE 12x20mm -- 4 pcs
12. SCREW PA1.7x8mm -- 6 pcs
MAIN WHEEL PL3112080 -- 2 sets
COLLAR Ø3.3mm w/ set screw -- 4 sets
SCREW PM2x8mm -- 6 pcs
WASHER d2xD5mm -- 6 pcs
M2 NUT -- 6 pcs
COPPER PLATE 0.5mm -- 6 pcs
BALSA 2x102x113mm (Main Landing Gear Cover) -- 2 pcs
13. SCREW PWA2.3x8mm -- 4 pcs
WIND SHIELD -- 1 pc.
SILICON GROMMET d1.5x6.5mm -- 4 pcs
SIDE WINDOWS -- 1 pair
14. COWLING -- 1 pc.
TRANSPARENT DUMMY COWLING -- 1 pc.
SCREW PWA2.6x12mm -- 4 pcs
SILICON GROMMET d1.5x6.5mm -- 4 pcs
15. LINKAGE CONNECTOR Ø2.1mm HW7111060 -- 1 set
16. PUSHROD Ø1.8x115mm (For Elevator) -- 1 pc.
PUSHROD CONNECTOR PL4410010 -- 1 set
SPONGE 60x70x105mm -- 1 pc.
PLYWOOD 3x57x115mm (For Fuselage Servos) -- 1 pc.
BALSA 6x8x108mm (For Fuselage Servos Stand) -- 2 pcs
STRAPER PL4112102 -- 2 pcs
FUEL TUBE Ø6x5mm -- 2 pcs
17. SCREW PB2x12mm -- 9 pcs
FUEL TUBE Ø6x5mm -- 3 pcs
CLEVIS PL4112103 -- 3 pcs
TRI-HORN M3x14mm (S) -- 3 sets
PUSHROD Ø1.8x735mm w/ Threads (For Rudder) -- 1 pc.
PUSHROD Ø1.8x640mm w/ Threads (For Elevator) -- 2 pcs
18. BALSA 3x45x112mm (For Pilot) -- 1 pc.
BALSA 6x8x45mm (For Pilot Stand) -- 2 pcs
SCREW PWA2x8mm -- 4 pcs
PILOT PC001063B -- 1 pc.
19. SOCKET HEAD SCREW HM4x30mm -- 2 pcs
WASHER d4xD15mm -- 2 pcs
SOCKET HEAD SCREW HM3x10mm -- 2 pcs
M3 NYLON INSERT LOCK NUT -- 2 pcs
20. DECALS A321DEC -- 1 set
A321PO26781107

PWA2x8mm
Plywood
2x52x80mm 1mm
2mm
Balsa
8x18x21mm
Make a slot into
the hatch for the
servo horn to come
out.
1mm
Aileron Servo
2
PWA2x8mm Screw8
Aileron Servo
3
P.3
Ø1mm pilot holes for The World Models tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
TWM PL8210010
CLEVIS WRENCH
Main Wing
1Aileron Servo Lead
PB2x18mm
Fuel Tube
Ø6x5mm
Fuel Tube
Ø6x5mm
Straper
Clevis
PB2x18mm Screw 6
Tri-horn
M3x14mm (S)
Pre-glued
Bottom View
Bottom View
Bottom View
A321PO26781107

Vertical Fin / Horizontal Stabilizer
6
Make sure vertical fin and stabilizer are at right angles.
Temporary install the main wing, adjust
leveling of the stabilizer to make it as
parallel to the main wing as possible.
Wing Struts
5
Thread Locker
Main Wing
4
Plywood
2x30x120mm
Aluminum Tube
Ø9.6x267mm
Join the wing halves by using the aluminium tube supplied
Strengthen both holes for the screws with a piece of plywood.
P.4
Bottom View
B B'
B=B'
(Stabilizer)
(Main Wing)
Pre-glued
Pre-glued
90
M3x18mm Socket Head Screw
M3x18mm
Socket Head Screw
PM2x12mm Screw
PM2x12mm
d2xD5mm Washer
4
4
8
4
PWA2X8mm Screw
PWA2X8mm
4
M2 Nut
d2xD5mm Washer
M2Nut
Copper Clipper
0.5x8x10mm
95mm
189mm
286.5mm
189mm 95mm
A321PO26781107

Tail Landing Gear
7
PA3x12mm Screw
3mm Set Screw
3mm Set Screw
2.1mm Collar
PM2x12mm Screw
PA3x12mmPM2x12mm
2
1
1
1
M2 Nut
1
Engine Mount
8
M4x25mm
Socket Head Screw
M4x25mm
Socket Head Screw
4
4
d4.5xD9mm Washer
Engine Mount
PL5111050
Engine
9
M3x25mm
Socket Head Screw
M3x25mm
Socket Head Screw
8
d3xD7mm Washer
d3xD7mm
Washer
d3xD7mm
Washer
8
M3 Nut
M3 Nut
Lead the 1.2mm throttle rod through the
plastic tube and attach the throttle rod
to the throttle lever on the engine.
Install Engine position
115mm
4.53in
Fire
Wall
d4.5xD9mm
Washer
P.5
A321PO26781107

Fuel Tank
10
Main Landing Gear
11
M3x16mm Socket Head Screw
PA3x8mm Screw
d3xD7mm Washer
2
6
2
2
2mm
3.1mm
Aluminum Plate
2mm
P.6
M3 NUT
PA3x8mm
d3xD7mm
Washer
M3 NUT
M3x16mm
UP
1
3
Cable Tie (For Fuel Tank)
1.5x5x400mm
Completed
Double-sided Tape 40x100mm
Double-sided Tape 40x100mm
Cable Tie
(For Fuel Tank)
1.5x5x400mm
2
Fuel Tank
260cc
A321PO26781107

P.7
Canopy
13
PWA2.3x8mm Screw
d1.5x6.5mm Silicon Grommet
d1.5x6.5mm
Silicon Grommet
4
4
PWA2.3x8mm
Securely glue the windows to the fuselage.
Cowling
14
PWA2.6x12mm Screw
PWA2.6x12mm
d1.5x6.5mm Silicon Grommet
d1.5x6.5mm
Silicon Grommet
4
4
Trim the cowling for the
engine head to project.
1.5mm
1.5mm
Please refer to the attached sheet for usage of the transparent 3D template.
First insert the grommet to the cowling then apply screw.
Cowling
Fuselage
d1.5x6.5mm
Silicon Grommet
PWA2.6x12mm
12
2.1mm
PM2x8mm
Copper Clipper
PM2x8mm Screw
PA1.7X8mm Screw
d2xD5mm Washer
d2xD5mm
Washer
d2xD5mm
Washer
6
6
6
6
4
3mm Set Screw
4
3.3mm w/set Collar
3.3mm
w/set Collar
PM2x8mm
PA1.7X8mm
Main Landing Gear
M2 Nut
M2 Nut
A321PO26781107

Rudder & Elevator Pushrod
17
P.8
PB2x12mm Screw 9Set the pushrods as shown in the diagram.
Ø1mm pilot holes for The World Models tri-horn
are pre-drilled. Please look for pin-hole marks
at under side of control surfaces.
TWM PL8210010
CLEVIS WRENCH
Bottom View
Rudder
Pushrod Elevator
Pushrod
PB2x12mm
Rudder
Tri-horn
Elevator
Tri-horn
Tri-horn
3x14mm
Clevis
PB2x12mm
Tri-horn
M3x14mm (S)
Fuel Tube
Ø6x5mm
Fuel Tube
Ø6x5mm
Clevis
Servo Set
15
1
1
3x3mm Set Screw
Linkage Connector
M2 Nut
2mm Washer 1
2
Please refer to the attached sheet for linkage connector installation.
Throttle Pushwire
3mm
Throttle Servo.
2mm
2mm
Washer
M2 Nut
2mm
Washer
Radio Equipment
16
Install and arrange the servos as shown in the diagram.
Fuel Tank
Receiver
Battery
Straper
Rudder
Ø1.8x735mm
Pushrod
Fuel Tube
Ø6x5mm
Elevator Pushrod
Ø1.8x640mm
Elevator Servo
Rudder Servo
Throttle Pushrod
Ø1.2x340mm
KM 2x8mm
M2 Nut
Elevator Pushrod
Ø1.8x115mm
Elevator Servo
Pushrod
Connector
J2(Pushrod Ø1.8x640)
J1(Pushrod Ø1.8x115) J1
J2
Throttle Servo
A321PO26781107

HM4x30mm
d4xD15mm
Washer
HM3x10mm
M3 Nylon Insert Lock Nut
3mm
19
Main Wing / Wing Struts
HM4x30mm
Socket Head Screw
d4xD15mm Washer
2
2
HM3x10mm
Socket Head Screw
M3 Nylon Insert Lock Nut
2
2
P.9
Cockpit
18
PWA2x8mmScrew
PWA2x8mm
4
PC001063B
Balsa
3x45x112mm
Balsa
6x8x45mm
1.5mm
A321PO26781107

P.10
Wing Setting
20
AA’
B
CB’ C’
Securely attach the
main wing
A=A’ B=B’ C=C’
A321PO26781107

# First time flyer should never fly by himself / herself. Assistance from experienced
flyer is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# is specially designed to be powered by 2C 0.40-0.46 or 4C 0.52-0.56
engine, using a more powerful engine does not mean better performance. In fact,
over powered engine may cause severe damage and injuries.
# Make sure the air field is spacious, never fly the plane too close to people and never
get too close to a running propeller.
# If you find wrinkles on the covering as a result of weather changes, you can use hot
iron to remove the wrinkles. Please begin with lower temperature setting and
gradually raise the temperature until the wrinkles are gone. Too hot an iron may
damage the covering. Don't use hot iron near the seams or edges, hot iron will
melt the glue and shrink the covering at the same time, causing the seams to pull away.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
Control Throws
21
Rudder
Elevator
Aileron
25mm
25mm
20mm
20mm
10m
http://www.theworldmodels.com/para/instruction/instructionManuals.php
m
10mm
Adjust the control throws as shown in
the diagram. These throws are good for
general flying. You can adjust according
to your personal preference.
C.G.
22
The ideal C.G. position is 70mm (2.76 in) behind
the leading edge measured at where the wing
meets the fuselage. In order to obtain the C.G.
specified, add weight to the fuselage or move
the battery position. Check the C.G. before flying.
P.11
Important Safety Precautions
PAULISTINHA P-56
Warning!
70 mm
2.76 in
A321PO26781107

This transparent 3D template
is used for position guidance
of the actual cutting of the
pre-painted cowling.
Usage of the transparent 3D template
Simply cut the transparent 3D template to fit your engine and
exhaust pipe, then slide onto the actual cowling and use as
template to mark the openings required for final cutting.
1 2
3 4
A321PO26781107

Product Registration Form (US Customers)
We would like to share with you any relevant information regarding your model, including
product news and free upgrade parts when applicable. Please fill in the following and send to
AirBorne Models, 4749-K, Bennett Drive, Livermore, CA94551 USA.
1. Name:______________________________________________
2.Address:____________________________________________
3. Phone #:____________________ E-mail:__________________
4. Model:______________________________________________
Wing QC#__________ Fuselage QC# _______________________
(QC numbers are stamped on wing and fuselage)
5. Date of Purchase:_____________________________________
6. Store Name: _________________________________________
Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.
Thank you very much for purchasing our product.
Drill 2mm hole at servo horn. Insert linkage connector
into servo horn.
Make sure shoulder of
screw is cleared from
servo horn.
Add washer to reduce
play if necessary.
Shoulder
Tighten up the round nut
against the shoulder. Apply
CA or permanent thread
locker.
After fastening the round nut, make sure that
the linkage connector can rotate freely.
LINKAGE CONNECTOR
HW7111050 & HW7111060
A321PO26781107

Fuel Filter
Code No. Size Package
Code No. Size Package
Code No. Size Package
Code No. Size Package
Code No. Size Package
Code No. Size Package
Code No SV4031
KP0041300
Special tool for clevis installation.
Suitable for standard and small
(EP)clevis.
Large Clevis
Small Clevis
180mmExtension
MS9111450 600 x 240 x 350mm 1 pc
A321PO26781107

The World Models
Manufacturing Co., Ltd.
www.theworldmodels.com
A321PO26781107