THE WORLD MODELS Sky Walker EP User manual

Wing Span 63.0 in / 1600 mm
Wing Area
Flying Weight
Fuselage Length
17 480 oz / g
420 sq in / 27 sq dm
3 in / 8 mm3 35
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
*Specifications are subject to change without notice.*
INSTRUCTION MANUAL
Specifications
Requires : 3- channel radio w/ 2 micro servos,
Outrunner Motor KM0283010
w/ Propeller Adaptor HW2340100
15A Brushless ESC,2 cells 7.4V
1000 mAh Li-Po battery & charger.
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
E182NXMPO25961107

P.1
INDEX
P. 3 -9
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P. 1
P. 2
P.9
BEFORE YOU BEGIN
1
2
3
3mm
Do not overlook this symbol!
Cut off shaded portion.
Peel off shaded portion
covering film.
Pay close attention here!
Pierce the shaded portion
covering film.
Must be purchased separately!
Drill holes with the specified
diameter (here: 3mm).
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Apply epoxy glue.
Apply thread locker
Warning!
E182NXMPO25961107

P.2
Parts list
1. MAIN WING -- 1 pair.
WING JOINER Ø4.5 x 161 mm -- 1 pc.
2. FUSELAGE -- 1 pc.
STABILIZER & ELEVATOR -- 1 set
3. VERTICAL FIN & RUDDER -- 1 set
4. PUSHROD Ø1.4X486 mm
w/ Threads(For Elevator ) – 1 pc.
SCREW PB2X8 mm -- 2 pcs
HORN PL4113102 -- 1 set
CLEVIS PL4112105 – 1 pc.
FUEL TUBE d2XD4X4 mm -- 1 pc.
5. PUSHROD Ø1.4 x 432 mm
w/ Threads(For Rudder) -- 1 pc.
SCREW PB2X10 mm -- 2 pcs
HORN PL4113102 -- 1 set
CLEVIS PL4113102 – 1 pc.
FUEL TUBE d2XD4X4 mm -- 1 pc.
6. SOCKET HEAD SCREW M3x6mm -- 4 pcs
WASHER d3xD7mm -- 4 pcs
FOLDING RPOPELLER SET (10X6)PL6314020 -- 1set
COWLING -- 1 pc.
SCREW PWA2X8 mm -- 4pcs
SPINNER Ø36 mm -- 1 set
7. SPONGE 10X50X150 mm -- 2 pc.
STRAPER PL4112106– 2 pcs
FUEL TUBE d2XD4X4 mm -- 2 pcs
DOUBLE-SIDED TAPE 30X35 mm -- 1 pc.
BATTERY TIE 200mm -- 1 pc.
8. PVC PLATE 0.8X20X42 mm(Wing Protection) -- 1 pc.
SCREW PM2.5X16 mm -- 2 pcs
WASHER d2.6XD9 mm -- 2 pcs
9. CANOPY -- 1 set
10. DECALS:E182NXMDEC -- 1 set
COVERING:
YELLOW COLOR SCHEME:
LIGHTEX SGX 000 TRANSPARENT
LIGHTEX SGX 030 TRANSPARENT YELLOW
LIGHTEX SGX 330 CADMIUM YELLOW
LIGHTEX SGX 100 WHITE
LIGHTEX SGX 201 BLACK
LIGHTEX SGX 312 BRIGHT RED
BLUE COLOR SCHEME:
LIGHTEX SGX 000 TRANSPARENT
LIGHTEX SGX 050 TRANSPARENT BLUE
LIGHTEX SGX 251 SKY BLUE
LIGHTEX SGX 100 WHITE
LIGHTEX SGX 201 BLACK
LIGHTEX SGX 350 CORSAIR BLUE
E182NXMPO25961107

Completed
Wing Joiner
Ø4.5 x 161mm
Main Wing
P.3
1
Stabilizer & Elevator
2Apply instant type CA glue to both sides of each hinge.
Completed
(Stabilizer)
(Main Wing)
AA'
B B'
B=B'
Temporary install the main wing, adjust
leveling of the stabilizer to make it as
parallel to the main wing as possible.
*Also refer to step 10 Wing Setting
Bottom View
E182NXMPO25961107

P.4
Vertical Fin / Rudder
3
Peel off shaded Portion
covering film.
Apply instant type CA glue to both sides of each hinge.
Completed
E182NXMPO25961107

P.5
Elevator Pushrod
4
7
PB2x10mm Screw
2
7
Rudder Pushrod
5
5mm
148mm
78mm
9mm
Pushrod
Ø1.4 x 445mm
Bottom View
PB2x8mm Screw
2
PB2x10mm
Clevis
Horn
Pushrod
Ø1.4x432mm
Fuel Tube
d2xD4x4mm
Horn
Pushrod
1.4x486mm
Fuel Tube
d2xD4x4mm
Clevis
PB2x8mm
TWM PL8210010
CLEVIS WRENCH
TWM PL8210010
CLEVIS WRENCH
Ø1mm pilot holes for World Models tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control
surfaces.
Ø1mm pilot holes for World Models tri-horn are pre-drilled.
Please look for pin-hole marks at side of control surfaces.
E182NXMPO25961107

P.6
6Motor / Cowling Setting
PWA2x8mm Screw
4
4
M x mm Sock Head Screw3 6
PM2x12mm Screw
4
2
PA2.6x8mm Screw
d3xD7mm Washer
4
56
7
4
3
Spinner
PM2x12mm
PM2x12mm
PA2.6x8mm
PWA2x8mm
Don't over-tighten the PM2 screws,
let the propeller blades align
themselves when spinning.
M5 Nut
TWM
KP0011310
SolderSolder
2 M3x6mm
Socket Head Screw
d3xD7mm
Washer
Don't over-tighten the
PM3 screws, too much
stress on the screws
could split the firewall.
TWM HW3111400
PROPELLER ADAPTOR WRENCH
Outrunner Motor 28/ 30
KM0283010
Propeller Adaptor
(d3xD5) HW2340100
Optional Parts
E182NXMPO25961107

P.7
C a nopy
9
Radio Equipment
Rudder Pushrod
Install and arrange the servo as shown in the diagram.
7
Main Wing
8
d2.6xD9mm Washer
PM2.5x16mm Screw
2
2
PM2.5 x 16mm
Wing Protection
0.8 x 25 x 61mm
d2.5 x D8mm PM2.5 x 16mm
2.5mm
Peel off shaded portion covering film.
Bottom View
d2.6 x D9mm
Completed
Rudder Servo
Straper Sponge
Fuel Tube
D2XD4X4mm
Elevator Pushrod
Brushless ESC
Elevator Servo
Battery
Double-Sided Tape
Battery Tie
Front
E182NXMPO25961107

P.8
Wing Setting
10
Adjust the wing and fuselage configuration as shown in the diagrams.
A=A' B=B' C=C'
A A'
BB'
C'C
Adjust the control throws as shown in the
diagram. These throws are good for general
flying. You can adjust according to your
personal preference.
Elevator
Rudder
25mm
25mm
10mm
10mm
Control Throws
11
E182NXMPO25961107

6.Store Name:
5.Date of Purchase:
Wing QC# Fuselage QC#
(QC numbers are stamped on wing and fuselage)
4.Model:
3.Phone #: e-mail:
2.Address:
1.Name:
The ideal C.G. position is 53mm (2.1 in.) ehind the leading edge
measured at where the wing meets the fuselage. In order to obtain
the C.G. specified, add weight to the fuselage or move the battery
position. Check the C.G. Before flying.
b
53mm
C.G.
2.1 in.
Important Safety Precautions
Warning!
P.9
C.G.
12
#First time flyer should never fly by himself/herself. Assistance from experienced flyer is
absolutely necessary.
#Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# is specially designed to be powered by KM0283010 Outrunner Motor.
to higher speed which will damage the wing structure and airframe, and will not be covered
by manufacturer’s warranty.
#Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller.
#If you find wrinkles on the covering as a result of weather changes, you can use hot iron
to remove the wrinkles. Please begin with lower temperature setting and gradually raise
the temperature until the wrinkles are gone. Too hot an iron may damage the covering.
#Check and re-tighten up all factory assembled screws, use thread locker if applicable.
with 2-cell 7.4V Li-Po battery operation. Using more powerful system will push the model
Product Registration Form (US Customers)
We would like to share with you any relevant information regarding your model, including
product news and free upgrade parts when applicable. Please fill in the following and send to
Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.
Thank you very much for purchasing our product.
Air orne Models, 4749-K, Bennett Drive, Livermore, CA 94551 USAB .
http://www.theworldmodels.com/para/instruction/instructionManuals.php
E182NXMPO25961107

Large Clevis
Small Clevis
Pl8210010
E182NXMPO25961107

The World Models
Manufacturing Co., LTD.
www.theworldmodels.com
Warbirds
Scale
Sports
Trainer
DuctedFan Pattern
Funfly
Electric
Glider
Boat
Accessories
Covering
(Lightex / Toughlon)
E182NXMPO25961107