Thelin PARLOUR Manual

Thelin Hearth Products
Parlour and Gnome
Pellet Stove
Maintenance Procedure
1

Table of Contents
1. Daily Maintenance 3
2. Weekly Maintenance 4
3. Monthly Maintenance 12
4. Yearly Maintenance 13
2

Parlour & Gnome Pellet Stove Daily Maintenance
3
Step 1
STOVE MUST BE COMPLETELY COLD BEFORE
PEROFORMING MAINTENANCE.
Remove Firepot and thoroughly clean with a
wire brush. Ensure holes are clear and are not
obstructed by silica, clinkers or fly ash.
Step 2
Scrape inside of Firepot with putty knife to
remove clinkers. Ensure holes are
unobstructed.
Reinstall Firepot.
Step 3
Wipe Front Door glass as needed.

Parlour & Gnome Pellet Stove Weekly Maintenance
4
Step 1
STOVE MUST BE COMPLETELY COLD BEFORE
PEROFORMING MAINTENANCE.
Open Front Door and remove left side Clean
Out Cover.
Step 2
Leave Front Door open so there is a one inch
gap.
Step 3
Press the “Clean” button on the Switch Panel
and let stove run for 30 seconds then push
“Off ”.

Parlour & Gnome Pellet Stove Weekly Maintenance
5
Step 4
Connect the vinyl vacuum hose to your ash
vacuum.
If you ash vacuum does not have a fitting to
accept the vinyl hose, use the vacuum
adapter provided.
Step 5
Thoroughly vacuum the left side heat
exchanger compartment.
Reinstall Clean Out cover when done.

Parlour & Gnome Pellet Stove Weekly Maintenance
6
Step 6
Remove the right side Clean Out Cover.
Step 7
Leave Front Door open so there is a one inch
gap.
Step 8
Press the “Clean” button on the Switch Panel
and let stove run for 30 seconds then push
“Off ”.

Parlour & Gnome Pellet Stove Weekly Maintenance
7
Step 9
Thoroughly vacuum the right side heat
exchanger compartment.
Reinstall Clean Out cover when done.
Step 10
Scrape Feed Chute with putty knife.
Remove creosote, fly ash build up and
accumulated sawdust.
Step 11
Remove Firepot and thoroughly clean with a
wire brush. Ensure holes are clear and are not
obstructed by silica, clinkers or fly ash.

Parlour & Gnome Pellet Stove Weekly Maintenance
8
Step 12
Scrape inside of Firepot with putty knife to
remove clinkers. Ensure holes are
unobstructed.
Step 13
Vacuum Feed Chute.
Step 14
Vacuum Igniter hole.

Parlour & Gnome Pellet Stove Weekly Maintenance
9
Step 15
Vacuum Firepot Holder compartment.
Reinstall Firepot when done.
Step 16
Vacuum left side of stove ash pockets next to
Firepot.
Step 17
Vacuum right side of stove ash pockets next to
Firepot.

Parlour & Gnome Pellet Stove Weekly Maintenance
10
Step 18
Vacuum Fan Guard. Fan Guard must be kept
free of dust build up and lint.
A blocked Fan Guard may cause stove to
overheat, triggering the T1 Sensor and
shutting the stove down.
Step 19
Wipe Front Door glass.
Step 20
Vacuum inside of Hopper as needed. Remove
accumulated sawdust.
Excessive build up of sawdust can cause
irregular pellet feed.

Parlour & Gnome Pellet Stove Weekly Maintenance
11
Step 21
Polish plated components as needed.
Always clean gold plated parts only when
the heater is cool.
Step 22
Wipe Front Door glass.
Step 23
Vacuum inside of Hopper as needed. Remove
accumulated sawdust.
Excessive build up of sawdust can cause
irregular pellet feed.

Parlour & Gnome Pellet Stove Monthly Maintenance
12
Step 1
STOVE MUST BE COMPLETELY COLD AND
UNPLUGGED BEFORE PEROFORMING
MAINTENANCE.
Check Clean Out Cap on Tee Connector on
vent pipe.
Step 2
Inspect the exhaust system frequently. Fly ash
can accumulate in the vent pipe. Initial
monitoring of the build-up in the vent pipe is
necessary.

Parlour & Gnome Pellet Stove Yearly Maintenance
13
Step 1
STOVE MUST BE COMPLETELY COLD AND
UNPLUGGED BEFORE PEROFORMING
MAINTENANCE.
Have certified personnel inspect and clean
venting as needed.
Step 2
Have certified personnel clean combustion
and exhaust fan assembly as needed.
See: “How To Replace Fan Motor Assembly”
procedure.
Step 3
Inspect Door gasket. Replace as necessary.
See: “How To Replace Door Gasket”
procedure.