Thermador HS Series User manual

READ AND SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS
HS-HST-HSB WALL HOODS
APPROVED FOR
RESIDENTIAL APPLIANCES
FOR RESIDENTIAL USE ONLY
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these nstructions for the Local Electrical nspectors use.
INSTALLER: Please leave these nstructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Safety Warning: Turn off power circuit at service panel and lock out
panel, before wiring this appliance.
Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit

Page 2
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: FORGENERALVENTI-
LATING USE ONLY. DO NOT USE
TO EXHAUST HAZARDOUS OR
EXPLOSIVE MATERIALS OR VA-
PORS.
WARNING-TOREDUCETHERISK
OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
A. Use this unit only in the manner
intended by the manufacturer.
f you have questions, contact
the manufacturer (Thermador
Customer Service at 800/
735.4328).
B. Before servicing or cleaning the
unit, switch power off at service
panel and lock service panel
disconnecting means to prevent
power from being switched on
accidentally. When the service
disconnecting means cannot be
locked, securely fasten a
prominent warning device,
such as a tag, to the service
panel.
C. nstallation Work and Electri-
cal Wiring Must Be Done By
Qualified Person(s) n Accor-
dance With All Applicable Codes
& Standards, ncluding Fire-
rated Construction.
D. Sufficient air is needed for
proper combustion and ex-
hausting of gases through the
flue (chimney) of fuel burning
equipment to prevent back-
drafting. Follow the heating
equipment manufacturers
guideline and safety standards
such as those published by the
National Fire Protection Asso-
ciation (NFPA), the American
Society for Heating, Refrigera-
tion and Air Conditioning Engi-
neers (ASHRAE), and the local
code authorities.
E. When cutting or drilling into
wall or ceiling, do not damage
electrical wiring and other
hidden utilities.
F. Ducted systems must always be
vented to the outdoors.
CAUTION: To reduce risk of fire
and to properly exhaust air, be
sure to duct air outside - do not
vent exhaust air into spaces
withinwalls,ceilings,attics,crawl
spaces, or garages.
WARNING - TOREDUCETHERISK
OFFIRE,USEONLYMETALDUCT
WORK.
nstall this hood in accordance with
all requirements specified.
WARNING - To Reduce The Risk
Of FireOr ElectricShock,DoNot
UseThisHood WithAnyExternal
Control Device.
CAUTION: To Reduce The Risk Of
Fire And Electric Shock, nstall
This Rangehood Only With Blower
Models specified.

Page 3
IMPORTANT SAFETY INSTRUCTIONS
WARNING- TOREDUCETHERISK
OF A RANGE TOP GREASE FIRE.
a) Never leave surface units
unattended at high settings.
Boilovers cause smoking and
greasy spillovers that may
ignite. Heat oils slowly on low
or medium settings.
b) Always turn hood ON when
cooking at high heat or when
flambeing food (i.e. Crepes
Suzette, Cherries Jubilee,
Peppercorn Beef Flambee).
c) Clean ventilating fans
frequently. Grease should not
be allowed to accumulate on
fan or filter.
d) Use proper pan size. Always
use cookware appropriate for
the size of the surface element.
WARNING - TO REDUCE THE
RISK OF INJURY TO PERSONS,
INTHEEVENT OF A RANGETOP
GREASE FIRE, OBSERVE THE
FOLLOWING:
a) SMOTHER FLAMES with a
close-fitting lid, cookie sheet,
or other metal tray, then turn
off the gas burner or the electric
element. BE CAREFUL TO
PREVENT BURNS. f the flames
do not go out immediately,
EVACUATE AND CALL THE F RE
DEPARTMENT.
b) NEVER P CK UP A FLAM NG PAN
- you may be burned.
c) DO NOT USE WATER, including
wet dishcloths or towels - a
violent steam explosion may
result.
d) Use an extinguisher ONLY if:
1)You know you have a class
ABC extinguisher, and you
already know how to operate it.
2)The fire is small and
contained in the area where it
started.
3)The fire department is being
called.
4)You can fight the fire with
your back to an exit.

Page 4
ATTENTION: SEULEMENTPOUR
L’UTILISATIOND’AÉRATION. NE
PAS L’UTILISER POUR ÉPUISER
LA VAPEUR OU LES MATIÈRES
EXPLOSIVESOUDANGEREUSES.
AVERTISSEMENT - POUR
RÉDUIRE LE RISQUE
D’INCENDIE, DE CHOC
ÉLECTRIQUE, OU DE LA
BLESSUREAUXPERSONNES,OB-
SERVER LE SUIVANT:
A. Utiliser cet appareil seulement
dans la manière destinée par
le fabricant. Si vous avez des
questions, contacter le
fabricant.
B. Avant lentretien ou le
nettoyage de lappareil, couper
le courant au tableau de ser-
vice, et fermer à clef la moyenne
de débrayage de service pour
empêcher lalimentation dêtre
allumée par hasard. Quand la
moyenne de débrayage de ser-
vice ne peut pas être fermée à
clef, attacher une étiquette au
tableau de service pour indiquer
que l'alimentation a été coupée
pour l'entretien.
C. Le Travail d nstallation et de
Câblage Électrique Doit Être Fait
Par les Personne(s) Qualifiées
Conformément à Tous les Codes
& Normes Applicables, y
Compris la Construction
Calculée à Feu.
D. Lécoulement comburant pour
le fonctionnement sûr du
matériel de la combustion du
combustible peut être affecté
par le fonctionnement de cet
LES INSTRUCTIONS DE SÉCURITÉ IMPORTANTES
appareil. Suivre la directive
des fabricants du matériel
chauffant et les normes de
sécurité tel que ceux publiées
par lAssociation du Protection
de Feu National (NFPA), et la
Société Américaine pour les
ngénieurs de Chauffage, de
Réfrigération et de Climatisa-
tion (ASHRAE), et les autorités
des codes locales.
E. En coupant ou en forant dans
un mur ou dans un plafond, ne
pas endommager le câblage
électrique et des autres
utilités cachées.
F. Les ventilateurs canalisés
doivent être toujours
déchargés à lextérieur.
ATTENTION: Pour réduire le
risque d’incendie, utiliser
seulement le travail du conduit
métallique.
nstaller ce capot conformé- ment
aux toutes exigences spécifiées
par le fabricant de votre cooktop/
cuisinière.
ATTENTION: Pour réduire le
risque d’incendie, de choc
électrique, ne pas utiliser cette
hotte avec aucun dispositif de
contrôle exterieur.
ATTENTION: Pour réduire le risque
dincendie, de choc électrique,
installer cette hotte seulement
avec des modeles des moteurs
indiqués.

Page 5
LES INSTRUCTIONS DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT - POUR
RÉDUIRE LE RISQUE D’UN FEU
DE GRAISSE DU SOMMET DE LA
CUISINIÈRE:
1. Garder le ventilateur, les
filtres et les surfaces chargées
de la graisse propres.
2. Toujours mettre le capot EN
MARCHE en cuisinant à la
haute chaleur.
3. Utiliser les hauts
positionnements du
cuisinière sur la cuisinière
seulement quand cest
nécessaire. Chauffer lhuile
lentement sur un positionnement
bas à moyen.
4. Ne pas laisser la cuisinière
sans surveillance pendant la
cuisson.
5. Utiliser toujours les batteries
de cuisine et les ustensiles
appropriés pour le type et la
quantité de la nourriture ayant
préparée.
AVERTISSEMENT: - POUR
RÉDUIRE LE RISQUE DE
BLESSURE AUX PERSONNES
DANS L’ÉVÉNEMENT D’UN FEU
DE GRAISSE DU SOMMET DE LA
CUISINIÈRE, OBSERVER LES
SUIVANTS:
a) ÉTOUFFER LES FLAMMES avec
un couvercle ajusté, une tôle
du biscuit ou un plateau
métallique, puis fermer le bec.
SOYEZ CERTA N DEMPÊCHER
LES BRÛLURES. Si les
flammes ne séteindront pas
immédiatement, ÉVACUER ET
APPELER LE SERV CE DES
NCEND ES.
b) NE JAMA S RAMASSER UNE
CASSEROLE EN FLAMMES -
Vous pouvez être brûlé.
c) NE PAS UT L SER DE LEAU, y
compris les torchons mouillés
ou les serviettes - une
explosion violente résultera.
d) Utiliser un extincteur
SEULEMENT si:
1) Vous savez que vous
avez un extincteur de Classe
ABC et vous. savez déjà
comment le faire fonctionner.
2) Le feu est petit et est
contenu dans la région où il a
commencé.
3) Le service des incendies
est appelé.
4) Vous pouvez combattre
le feu avec votre dos à une
sortie.

Page 6
Parts Included with your
Hood
•Hood Canopy Assembly with
Light Bulbs nstalled
 Care & Use / nstallation
nstructions
 Registration Card
 Filters, 2, 3 or 4 depending on
model and size
 Metal Transition with Back
draft dampers installed (On
HST Series hoods it is
temporarily fixed for shipping
inside the hood with two
screws)
 Screws and Drywall Anchors
 Remote Blower (pigtail)
Adaptor (HS and HST Series
hoods only)
 Wooden Strip for Hood
Support (HST Series hoods
only)
 Mounting Hooks
 Wire Clamp (HS and HST
Series hoods only)
 Side mould (HSB30 and HS30
Series hoods only)
 Contents Sheet
Parts Not Included with
your Hood
 Duct Tape
 1/2" Conduit
 Wire Nuts
 Ventilator- The HS and HST
series Hoods can be installed
with any Thermador
VTR600R, VTR1000Q,
VTN420B or VTN620B Blower
 Optional duct cover, 6 or 12
height (HSB and HS Series
hoods only)
 Optional telescopic duct cover
(HST Series hoods only).
 R Lamp (Purchase and use
only lamps mod. 175R-PAR,
175W maximum infrared
bulbs).
 Recirculating kit (HSB and HS
Series hoods only)

Page 7
BEFORE INSTALLING HOOD
1. For the most efficient air flow
exhaust, use a straight run or
as few elbows as possible.
CAUTION: Vent unit to
outside of building, only.
2. Almost two people are
necessary for installation.
3. The hood is fitted with Screws
and Drywall Anchors suitable
for most surfaces, consult a
Qualified nstaller, check if
they perfectly fit with your
cabinet/wall.
4. Do not use flex ducting.
5. COLD WEATHER installations
should have an additional
backdraft damper installed to
minimize backward cold air
flow and a nonmetallic
thermal break to minimize
conduction of outside tem-
peratures as part of the
ductwork. The damper should
be on the cold air side of the
thermal break.
The break should be as close
as possible to where the
ducting enters the heated
portion of the house.
6. Remote blowers require a five
wire installation.
7. Make up air: Local building
codes may require the use of
Make-Up Air Systems when
using Ducted Ventilation
Systems greater than
specified CFM of air
movement.
The specified CFM varies
from locale to locale. Consult
your HVAC professional for
specific requirements in your
area.

Page 8
HOOD WIDTH DIM. "A"
30" 12 - 3/16"
36" 15 - 3/16"
42" 18 - 3/16"
48" 21 - 3/16"
HOOD DEPTH DIM. "B"
30" 22 - 11/16"
36" 23"
42" 23 - 5/16"
48" 23 - 7/8"
Note: t is important to select the
ventilator to be used before
cutting the duct opening on the
cabinet or wall.
Figure 1
Figure 2
4-1/ "
1/2"
(HS-HSB)
4-3/4"
(HST)
-1/16"
(HST)
1/2"
(HS-HSB)
Cabinet
Cabinet Front
A
5-7/8"
4-7/8"
1 "
Vertical
Discharge
1-7/8"
4-3/8"
Hood Width
0"
Optional Rear
Discharge
Rear
Wall
Bottom of
Cabinet or
Soffit
1-1/2"
Dia. Holes
9"
1 "
11"
B
4"
B
18"
HSB and HS
Series Hoods
HST
Series Hoods
Table 1
Table 2
BEFORE INSTALLING HOOD
APPLIANCE INSTALLATION
CABINETORSOFFITPREPARATION

Page 9
TYPICALINSTALLATION
The hoods are designed for either
vertical or horizontal discharge as
shown in Figure A and B
respectively.
The height from the countertop
tothebottomofthehoodis30"to
36”.These hoods are not
recommended to be used over
indoor grills.
DUCTING
Provide a Round Duct having a
diameter of 8 (see Figure A and B
for location and Figure 1 for location
on wall or cabinet bottom).
nstall a 1/2 conduit from the
service panel long enough to reach
the hood once it is installed.
Power supply must be rated for 120V
60Hz, 15 amps (minimum).
Note - Horizontal Discharge:
The Transition for this discharge
direction is not supplied and
must be purchased separately.
BEFORE INSTALLING HOOD

Page 10
plate
fixing
point
Plate
Figure 3
Discharge Direction: The hood is
shipped ready for horizontal
discharge. To change to vertical
discharge move plate to the rear
side and ventilator (if supplied) to
the top side.
The plate and ventilator are held in
place by four nuts each, see also
Figures 3 and ,at page 9, Figure A
and Figure B.
Read also paragraph  ntegral
Ventilator nstallation at pages
14-15 for further informations.
Note: f an integral ventilator is
already supplied (HSB series hoods
only), remove it to allow installation
of hood to the wall/cabinet.
Assembly of the Transition:
The transition supplied with the
hood mounts to the top of the
hood, Figure 4.
1. Fold outwards all six Tabs (HS
and HSB series only).
2.Align mounting holes at base
of transition with mounting
holes on 1/2 flange located at
the top of the hood.
3.Fasten transition to hood using
6 (4 mm x 9.5 mm) screws
(included with hood).
4.Duct tape connection between
transition and hood.
5. Remove tape holding damper
Transition
Top outlet
Tongue
Figure 4
BEFORE INSTALLING HOOD
Tab