Thermasol SS-84 User manual

DOC NO. 81078 Page 1 of 18 Rev D 3/06 GM
Installation Instructions
Steam Shower Series
With Fast Start Technology
Manufacture Post 2005
If you are a plumber installing this unit, please leave
this owners manual & warranty card with the owner
when you finish the installation.
This Instruction supercedes all previous information provided by ThermaSol
Thank You!
CONSUMER WARNING
•DO NOT USE THIS PRODUCT UNLESS YOU HAVE CONSULTED YOUR DOCTOR AND RECEIVED WRITTEN PERMISSION TO DO SO.
USE OF THIS PRODUCT MAY BE HAZARDOUS TO YOUR HEALTH.
•STEAM IS HOT! DO NOT TOUCH OR GO NEAR THE STEAMHEAD FROM THE TIME THE UNIT IS “ON”, UP TO ONE HOUR FROM THE
TIME THE UNIT IS OFF. SEVERE BURN WILL OCCUR IF YOU COME IN CONTACT WITH THE STEAMHEAD OR STEAM EMITTING FROM
THE STEAMHEAD.
•NEVER ATTEMPT TO FILL AROMA THERAPY RESERVOIR ON THE STEAMHEAD WHEN UNIT IS IN THE “ON” POSITION. SEVERE
BURNS WILL OCCUR.
•DO NOT USE THERMASOL AROMA THERAPY OILS OR SKIN CARE PRODUCTS OR ANY PRODUCT IN CONJUNCTION WITH YOUR
THERMASOL UNIT WITHOUT CONSULTING WITH YOUR ALLERGIST OR DOCTOR BEFORE USE. THESE PRODUCTS MAY BE
HAZARDOUS TO YOUR HEALTH.
•YOUR SHOWER MAY BE A SLIP AND FALL HAZARD CHECK WITH YOUR CONTRACTOR OR FLOORING MANUFACTURER
REGARDING THE SAFE USE OF YOUR FLOORING IN A STEAM APPLICATION. SLIPPING AND FALLING INTO THE STEAMHEAD
ITSELF OR INTO THE STREAM OF STEAM EMITTING FROM THE STEAMHEAD WILL CAUSE SERIOUS BURNS, OR PHYSICAL INJURY.
•DO NOT USE STEAM ROOM WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS, AS THIS CAN BE HAZARDOUS TO YOUR
HEALTH.
•IF YOU ARE FEELING UNCOMFORTABLE, DIZZY, FAINT, OR STARTING TO FALL ASLEEP IMMEDIATELY EXIT THE STEAM ROOM.
•DO NOT USE STEAM ROOM IF YOU ARE UNDER THE AGE OF 16 UNLESS SUPERVISED BY AN ADULT.
Note: Before contacting Customer Service for Technical Support, please have the model number,
serial number and date code (located on a circle to the lower right of the serial number), include
all numbers and letters.
Headquarters & Technical Support
2255 Union Place, Simi Valley, CA 93065 – [phone]
Mon – Thur 7:00 – 5:00, Fri 8:00 – 12:00 PST
Eastern Sales Office
26 Industrial Avenue, Fairview, NJ 07022 – [phone]
Mon – Thur 7:00 – 5:00, Fri 8:00 – 12:00 EST
www.thermasol.com

DOC NO. 81078 Page 2 of 18 Rev D 3/06 GM
** NOTICE **
WARNING LABEL THERMASOL
CONTROL
THERMASOL
STEAMHEAD
SHOWER FLOOR
YOU MUST ATTACH THIS STATIC
CLING USER WARNING LABEL IN THE
SHOWER NEXT TO THE CONTROL
UPON COMPLETION OF
INSTALLATION

DOC NO. 81078 Page 3 of 18 Rev D 3/06 GM
Generator Installation Instructions
Parts Enclosed
•NoTouch Steamhead housing
•Steam generator
•50 foot control cord
•Test kit with Instructions
•Installation Instructions
•Warranty card
•Static cling warning label
All ThermaSol steam generators are designed to build NO PRESSURE during operation. This is
for your safety.
Note: Failure to follow installation instructions specifically will cause the warranty to be void.
Figure 1
Note: The generator must be mounted level with all connections on top.
PRESSURE
RELIEF VALVE
CONTROL CABLE
INPUT
FRONT OF GENERATOR
(ACCESS PANEL)
POWERFLUSH BALL VALVE
IN CLOSED POSITION
WATER
INLET
17”
12” AT
PIPING
CLEANCE
11-1/2”
IDENTIFICATION LABEL
ELECTRICAL BOX
POWERFLUSH BALL

DOC NO. 81078 Page 4 of 18 Rev D 3/06 GM
Generator Installation Instructions (con’t)
Materials Needed
•Brass ball valve (for water supply shut off)
•Pipe compound
•Copper or brass fittings & nipples (sizes and quantities per instructions)
•In-line water filter (recommended)
•3/8” brass or copper union
•1/2” brass or copper union
•Wire (sizes and quantities per instructions)
•Copper tubing or pipe
•Wire cap nuts
•Flex conduit
•Silicone
•Other materials as required
Tools Needed
•Pipe wrench
•Tubing cutter
•Wire cutters or wire strippers
•Adjustable wrench
•Screwdrivers (phillips & regular)
•Solder & Flux
•1-1/16” masonry drill bit
•2-1/2” hole saw for NoTouch Steamhead
•Drill motor
•Propane torch
•Other tools as required
Note: ThermaSol steam bath generators are for indoor use only. They should never be
located outside the home.
Note: ThermaSol steam bath generators are NOT designed to be used for space heating
purposes.
Warning: Please consult your physician before using. If you are pregnant, elderly, have high
blood pressure, diabetes, suffering from heart disease, intoxicated, or not in good health, do not
use this steam bath.

DOC NO. 81078 Page 5 of 18 Rev D 3/06 GM
CONSUMER WARNING
WARNING
DO NOT USE THIS PRODUCT UNLESS YOU HAVE CONSULTED WITH YOUR DOCTOR AND
RECEIVED WRITTEN PERMISSION TO DO SO. USE OF THIS PRODUCT MAY BE HAZARDOUS TO
YOUR HEALTH.
WARNING
NEVER ATTEMPT TO FILL AROMA RESERVOIR ON THE STEAMHEAD WHEN UNIT IS IN THE ON
POSITION. SEVERE BURNS WILL OCCUR.
WARNING
DO NOT USE THERMASOL AROMA THERAPY OILS OR SKIN CARE PRODUCTS OR ANY
PRODUCT IN CONJUNCTION WITH YOUR THERMASOL UNIT WITHOUT CONSULTING WITH
YOUR ALLERGIST OR DOCTOR BEFORE USE. THESE PRODUCTS MAY BE HAZARDOUS TO
YOUR HEALTH.
WARNING
YOUR SHOWER MAY BE A SLIP AND FALL HAZARD CHECK WITH YOUR CONTRACTOR OR
FLOORING MANUFACTURER REGARDING THE SAFE USE OF YOUR FLOORING IN A STEAM
APPLICATION. SLIPPING AND FALLING INTO THE STEAMHEAD ITSELF OR INTO THE STREAM
OF STEAM EMITTING FROM THE STEAMHEAD WILL CAUSE SERIOUS BURNS, OR PHYSICAL
INJURY.
WARNING
STEAM IS HOT! DO NOT TOUCH OR GO NEAR THE STEAMHEAD FROM THE TIME THE UNIT IS
“ON”, UP TO ONE HOUR AFTER IT HAS SHUT OFF. SEVERE BURN WILL OCCUR IF YOU COME
IN CONTACT WITH THE STEAMHEAD OR STEAM EMITTING FROM THE STEAMHEAD.
WARNING
DO NOT USE STEAM ROOM WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS, AS THIS
CAN BE HAZARDOUS TO YOUR HEALTH.
WARNING
IF YOU ARE FEELING UNCOMFORTABLE, DIZZY, FAINT, OR STARTING TO FALL ASLEEP
IMMEDIATELY EXIT THE STEAM ROOM.
WARNING
DO NOT USE STEAM ROOM IF YOU ARE UNDER THE AGE OF 16 UNLESS SUPERVISED BY AN
ADULT.

DOC NO. 81078 Page 6 of 18 Rev D 3/06 GM
Requirements For Proper Installation
1. Ensure the steam room to be used is vapor proof. It should have a vapor proof door that seals well so
the steam does not escape. Make sure the walls, ceiling and floor materials are suitable for use with
steam and hot condensation, the steam produces.
2. Unit may be installed up to 50 feet away from steam room in a dry well ventilated area.
3. Use copper or brass fittings only (NEVER USE GALVANIZED FITTINGS).
4. The water inlet uses 3/8” NPT and steam outlet uses 1/2" NPT for easy installation.
5. The generator must be upright, accessible and on a level surface with all connections on top. Access
panel and powerflush valve must be unobstructed and allow for easy access (see Figure 1).
6. Place a drain/spill pan under the unit. Plumb the connection on it to an approved drain.
7. Connect a tee to the cold water line. Install copper pipe to the tee (see Figure 3).
8. Install a brass shut-off valve on the water inlet line in an accessible area prior to the brass union and
recommended in-line water filter.
9. Before making the last connection to the 3/8” NPT, flush the water line into a five-gallon pail to
remove any silt or other materials that may be in the line.
10. Make the final connection and turn on water. All ThermaSol generators are equipped with an
automatic water fill system. The water will stop after unit is filled.
11. The steam line can run up, down, or horizontal; but cannot run down and then up. If it does, a
steam trap will be produced at the low point blocking the flow of steam. Do not plumb a trap in the
steam line. Insulate the steam outlet piping if the piping run exceeds 10 feet or is exposed to cold
areas. Note: Use steam rated insulation.
12. Do not plumb the pressure relief valve into the steam line. Plumbing the pressure relief valve into
the steam line can be hazardous, should the steam outlet be capped off or obstructed.
13. Pitch/angle steam line back towards generator and avoid perfectly level plumbed lines.
14. Make sure water is turned on before operating the unit.
Note: Failure to follow installation instructions specifically will cause the warranty to be void.
Sizing Your Steam Room
Factory Sized: L x W x H = Cubic Feet
Then choose the appropriate Model. No complicated
formulas. It’s that simple. For every foot of ceiling
height over 8 ft. (always round up) use the next larger
steam unit. Wall material irrelevant.
Generator
Model Factory Sized Cu Ft MAX K W
SS-Acrylic Acrylic Insert 3.5
SS-84 84 6.0
SS-140 140 8.0
SS-240 240 10
SS-395 395 12
SS-600 500 15

DOC NO. 81078 Page 7 of 18 Rev D 3/06 GM
Figure 2
Various options for the ThermaSol steam bath generator location.
Important: MAXIMUM WATER PRESSURE not to exceed 70 P.S.I.
Warning: The Steamhead is HOT! Do not install Steamhead near a seat or bench
hot steam will burn you. Keep at least 12-14 inches away from hot steam exiting
the Steamhead.
Figure 3
Note: The generator must be mounted level with all connections on top.
COUPLER
ONETOUCH
CONTROL
STEAMHEAD
TEE
!!!!! IMPORTANT !!!!
LOCATE THE STEAMHEAD 12”
OFF THE SHOWER FLOOR OR
BATHTUB RIM AND 6” FROM
ANY CORNER. STEAMHEAD IS
TO BE MOUNTED FAR AS
POSSIBLE FROM TYPICAL
BATHING POSITION (SEATED
OR STANDING) AND AS FAR
FROM CONTROL AS POSSIBLE
WHILE MAINTAINING A 60”
CONTROL HEIGHT.
PRESSURE
RELIEF VALVE
50 FOOT
CONTROL
CABLE
SHUT-OFF
V
ALVE
WATER
INLLET
ELITE
CONTROL
CONTROL CABLE
INPUT FRONT OF GENERATOR
(ACCESS PANEL)
IDENTIFICATION LABEL
BRASS
UNION BRASS UNION
RECOMMENDED IN-LINE
WATER FILTER
SHOWER FLOOR OR
BATHTUB RIM
12”
6”
Drain Pan (Not supplied)

DOC NO. 81078 Page 8 of 18 Rev D 3/06 GM
CONSUMER WARNING
WARNING
DO NOT USE THIS PRODUCT UNLESS YOU HAVE CONSULTED WITH YOUR DOCTOR AND
RECEIVED WRITTEN PERMISSION TO DO SO. USE OF THIS PRODUCT MAY BE HAZARDOUS TO
YOUR HEALTH.
WARNING
NEVER ATTEMPT TO FILL AROMA RESERVOIR ON THE STEAMHEAD WHEN UNIT IS IN THE ON
POSITION. SEVERE BURNS WILL OCCUR.
WARNING
DO NOT USE THERMASOL AROMA THERAPY OILS OR SKIN CARE PRODUCTS OR ANY
PRODUCT IN CONJUNCTION WITH YOUR THERMASOL UNIT WITHOUT CONSULTING WITH
YOUR ALLERGIST OR DOCTOR BEFORE USE. THESE PRODUCTS MAY BE HAZARDOUS TO
YOUR HEALTH.
WARNING
YOUR SHOWER MAY BE A SLIP AND FALL HAZARD CHECK WITH YOUR CONTRACTOR OR
FLOORING MANUFACTURER REGARDING THE SAFE USE OF YOUR FLOORING IN A STEAM
APPLICATION. SLIPPING AND FALLING INTO THE STEAMHEAD ITSELF OR INTO THE STREAM
OF STEAM EMITTING FROM THE STEAMHEAD WILL CAUSE SERIOUS BURNS, OR PHYSICAL
INJURY.
WARNING
STEAM IS HOT! DO NOT TOUCH OR GO NEAR THE STEAMHEAD FROM THE TIME THE UNIT IS
“ON”, UP TO ONE HOUR AFTER IT HAS SHUT OFF. SEVERE BURN WILL OCCUR IF YOU COME
IN CONTACT WITH THE STEAMHEAD OR STEAM EMITTING FROM THE STEAMHEAD.
WARNING
DO NOT USE STEAM ROOM WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS, AS THIS
CAN BE HAZARDOUS TO YOUR HEALTH.
WARNING
IF YOU ARE FEELING UNCOMFORTABLE, DIZZY, FAINT, OR STARTING TO FALL ASLEEP
IMMEDIATELY EXIT THE STEAM ROOM.
WARNING
DO NOT USE STEAM ROOM IF YOU ARE UNDER THE AGE OF 16 UNLESS SUPERVISED BY AN
ADULT.

DOC NO. 81078 Page 9 of 18 Rev D 3/06 GM
NoTouch Steamhead Installation
Parts Enclosed
•NoTouch Steamhead housing (included w/generator)
Material Needed
•Clear silicone
•1/2” drop elbow
•ThermaSol NoTouch Steamhead (in desired finish)
•Other materials as required
Tools Needed
•1” deep socket and ratchet
•2-1/2” hole cutting tool
•Other tools as required
1. Drill a 2-1/2” diameter hole in the shower wall or wall above the bathtub rim for the steam outlet line
(see Figure 4).
CAUTION: The Steamhead is hot and should not be located near a seat or bench! We recommend
locating the Steamhead on the fixture wall.
** Ensure that all Plumbing is Firmly Secured. **
Figure 4
STEAMHEAD
STEAMHEAD
HOUSING
2-1/2” HOLE
1/2" PIPE
SHOWER WALL
1/2" TUBING
1/2" FEMALE
DROP ELBOW
2x4 WALL
THIS EDGE MUST BE FLUSH
WITH FINISHED WALL
(
+/- 1/8”
)

DOC NO. 81078 Page 10 of 18 Rev D 3/06 GM
2. Connect a 1/2" NPT brass pipe or tubing to the steam outlet on the generator running the pipe to the
2-1/2” diameter hole in wall to connect with the Steamhead housing. Use Figure 4 as a guide. It is
very important that the pipe is firmly secured to the wall, so that when the Steamhead is
installed it doesn’t push the housing back into the wall. The steam line can run up, down, or
horizontal; but cannot run down and then up. If it does, a steam trap may be produced at the low
point blocking the flow of steam. Install a 1/2” drop elbow on the end of the 1/2” pipe or tubing for the
Steamhead housing. For all the connections, use Teflon tape/solder and do not over tighten fittings.
DO NOT USE PVC CEMENT.
3. Final Installation when installing the Steamhead into the housing be sure that the aromatherapy fill
channels are facing upwards see Figure 5. To ensure that no moisture gets behind the Steamhead
and into the wall, place a generous bead of waterproof silicone around the Steamhead, use the
machined grove (located on the back of the Steamhead) as a guide. Be sure that within the housing
there isn’t any debris, and the two O-rings are in place on the Steamhead. Slide the Steamhead into
the housing until the Steamhead is tight against the finished wall. You may need to wipe away any
excess silicone. Use Figure 5 as a reference to these steps.
PLACE SILICONE AROUND
THIS GROOVE THIS EDGE MUST BE FLUSH
WITH FINISHED WALL
(
+/- 1/8”
)
AROMATHERAPY
FILL CHANNELS O-RINGS
FINISHED WALL
Figure 5
Warning: Avoid contact with Steamhead! It will burn you! Avoid direct contact with the steam
coming out of the Steamhead! It is extreamly hot and will burn you! Never put Aroma oil in the
Steamhead when the unit is in the on position, or when steam is emitting from the Steamhead.

DOC NO. 81078 Page 11 of 18 Rev D 3/06 GM
CONSUMER WARNING
WARNING
DO NOT USE THIS PRODUCT UNLESS YOU HAVE CONSULTED WITH YOUR DOCTOR AND
RECEIVED WRITTEN PERMISSION TO DO SO. USE OF THIS PRODUCT MAY BE HAZARDOUS TO
YOUR HEALTH.
WARNING
NEVER ATTEMPT TO FILL AROMA RESERVOIR ON THE STEAMHEAD WHEN UNIT IS IN THE ON
POSITION. SEVERE BURNS WILL OCCUR.
WARNING
DO NOT USE THERMASOL AROMA THERAPY OILS OR SKIN CARE PRODUCTS OR ANY
PRODUCT IN CONJUNCTION WITH YOUR THERMASOL UNIT WITHOUT CONSULTING WITH
YOUR ALLERGIST OR DOCTOR BEFORE USE. THESE PRODUCTS MAY BE HAZARDOUS TO
YOUR HEALTH.
WARNING
YOUR SHOWER MAY BE A SLIP AND FALL HAZARD CHECK WITH YOUR CONTRACTOR OR
FLOORING MANUFACTURER REGARDING THE SAFE USE OF YOUR FLOORING IN A STEAM
APPLICATION. SLIPPING AND FALLING INTO THE STEAMHEAD ITSELF OR INTO THE STREAM
OF STEAM EMITTING FROM THE STEAMHEAD WILL CAUSE SERIOUS BURNS, OR PHYSICAL
INJURY.
WARNING
STEAM IS HOT! DO NOT TOUCH OR GO NEAR THE STEAMHEAD FROM THE TIME THE UNIT IS
“ON”, UP TO ONE HOUR AFTER IT HAS SHUT OFF. SEVERE BURN WILL OCCUR IF YOU COME
IN CONTACT WITH THE STEAMHEAD OR STEAM EMITTING FROM THE STEAMHEAD.
WARNING
DO NOT USE STEAM ROOM WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS, AS THIS
CAN BE HAZARDOUS TO YOUR HEALTH.
WARNING
IF YOU ARE FEELING UNCOMFORTABLE, DIZZY, FAINT, OR STARTING TO FALL ASLEEP
IMMEDIATELY EXIT THE STEAM ROOM.
WARNING
DO NOT USE STEAM ROOM IF YOU ARE UNDER THE AGE OF 16 UNLESS SUPERVISED BY AN
ADULT.

DOC NO. 81078 Page 12 of 18 Rev D 3/06 GM
Electrical Installation
Note: All electrical wiring must be done per National/Local Electrical Codes.
** ThermaSol requires that a licensed electrician perform all electrical work. **
Note: USE COPPER WIRE ONLY.
Wire sizes recommended by NEC (2002 Version). Minimum wire temperature rating 90°C. Type THHN.
Generator
Model Phase Wire Gauge Breaker Size Factory Sized Cu Ft MAX AMP draw @ 240-VAC K W
SS-Acrylic 1 10 20 Acrylic Insert 17 3.5
SS-84 1 10 30 84 28 6.0
SS-140 1 8 40 140 37 8.0
SS-240 1 8 50 240 46 10
SS-395 1 6 60 395 55 12
SS-600 1 4 80 500 69 15
Electrical Questions? 800-776-0711 for Technical Support
Warning: Each generator should be wired to their own separate breaker.
1. Turn off all electricity to the working area at the main breaker panel!
2. Connect 240-VAC electrical lines to wires labeled 1 & 2 located in the electrical box on
generator, (refer to Figure 6).
Figure 6
Wiring diagram

DOC NO. 81078 Page 13 of 18 Rev D 3/06 GM
CONSUMER WARNING
WARNING
DO NOT USE THIS PRODUCT UNLESS YOU HAVE CONSULTED WITH YOUR DOCTOR AND
RECEIVED WRITTEN PERMISSION TO DO SO. USE OF THIS PRODUCT MAY BE HAZARDOUS TO
YOUR HEALTH.
WARNING
NEVER ATTEMPT TO FILL AROMA RESERVOIR ON THE STEAMHEAD WHEN UNIT IS IN THE ON
POSITION. SEVERE BURNS WILL OCCUR.
WARNING
DO NOT USE THERMASOL AROMA THERAPY OILS OR SKIN CARE PRODUCTS OR ANY
PRODUCT IN CONJUNCTION WITH YOUR THERMASOL UNIT WITHOUT CONSULTING WITH
YOUR ALLERGIST OR DOCTOR BEFORE USE. THESE PRODUCTS MAY BE HAZARDOUS TO
YOUR HEALTH.
WARNING
YOUR SHOWER MAY BE A SLIP AND FALL HAZARD CHECK WITH YOUR CONTRACTOR OR
FLOORING MANUFACTURER REGARDING THE SAFE USE OF YOUR FLOORING IN A STEAM
APPLICATION. SLIPPING AND FALLING INTO THE STEAMHEAD ITSELF OR INTO THE STREAM
OF STEAM EMITTING FROM THE STEAMHEAD WILL CAUSE SERIOUS BURNS, OR PHYSICAL
INJURY.
WARNING
STEAM IS HOT! DO NOT TOUCH OR GO NEAR THE STEAMHEAD FROM THE TIME THE UNIT IS
“ON”, UP TO ONE HOUR AFTER IT HAS SHUT OFF. SEVERE BURN WILL OCCUR IF YOU COME
IN CONTACT WITH THE STEAMHEAD OR STEAM EMITTING FROM THE STEAMHEAD.
WARNING
DO NOT USE STEAM ROOM WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS, AS THIS
CAN BE HAZARDOUS TO YOUR HEALTH.
WARNING
IF YOU ARE FEELING UNCOMFORTABLE, DIZZY, FAINT, OR STARTING TO FALL ASLEEP
IMMEDIATELY EXIT THE STEAM ROOM.
WARNING
DO NOT USE STEAM ROOM IF YOU ARE UNDER THE AGE OF 16 UNLESS SUPERVISED BY AN
ADULT.

DOC NO. 81078 Page 14 of 18 Rev D 3/06 GM
OneTouch Or Elite Control Installation Instructions
Warning: Power to the generator must be off prior to connecting any control.
1. The OneTouch digital control (shown in Figure 7) can be located inside or outside the enclosure.
2. The Elite control (shown in Figure 8) MUST be located INSIDE the enclosure.
3. Position the control 4 to 6 feet from the floor. Drill a 1-1/16” diameter hole into the wall.
M
M
COAT THE BACK COMPLETELY
WITH SUPPLIED WATERPROOF
SILICONE TO COMPLETELY
SEAL THE CONTROL TO THE
WALL AND NOT ALLOW
MOISTURE BEHIND IT
1-1/16“ DRILL HOLE IN WALL
FOR CONTROL CABLE
50 FT. CONTROL CABLE
FROM STEAM GENERATOR
COUPLER
2.15
4.00
ONETOUCH CONTROL
Figure 7
4. Bring the control cable(s) from the generator through the 1-1/16” diameter hole. Plug the modular
connector of the control into one end of the coupler. Plug the control cable(s) from the generator into
the other end of the coupler. Route the cable so that the coupler is located ABOVE the hole in
the wall. DO NOT pinch, nail, staple, wedge etc. the cable. DO NOT wrap the cable around
steam line or otherwise route it in such a manner that the hot steam line could melt the cable.
Any damage to the control cable will result in the control not working properly.
5. For OneTouch/Elite combination connect supplied phone jack splitter to the steam generator, refer
back to Figure 1.
6. Carefully connect the other end of the control cable to the generator BEFORE turning power on to the
generator.
7. Turn on both water and power to the generator.
8. Test the touch pad to ensure it is properly connected. If any technical problems arise, call toll-free
800-776-0711.
CAUTION
Do not use harsh or
abrasive cleaning
chemicals when cleaning
you
r
co
n
t
r
o
l.

DOC NO. 81078 Page 15 of 18 Rev D 3/06 GM
9. THESE STEPS MUST BE TAKEN OR YOUR WARRANTY WILL BE VOID.Coat the entire control
back with supplied waterproof silicon. Completely seal the control to the wall so moisture does not get
behind it. Place the control on the wall pressing firmly. You may need to tape the control into place
until the silicone dries. Be careful not to harm the wall/control with the tape. Let dry for 24 hours
before using steam bath.
10. Refer to operation instructions for control functions.
Note: Failure to follow installation instructions specifically will cause the warranty to be void.
COAT THE BACK COMPETELY
WITH SUPPLIED WATERPROOF
SILICONE TO COMPLETELY
SEAL THE CONTROL TO THE
WALL AND NOT ALLOW
MOISTURE BEHIND IT
1-1/16“ DRILL HOLE IN WALL
FOR CONTROL CABLE
50 FT. CONTROL CABLE
FROM STEAM GENERATOR
COUPLER
2.95
5.00
Figure 8
CAUTION
Do not use harsh or
abrasive cleaning
chemicals when cleaning
you
r
co
n
t
r
o
l.

DOC NO. 81078 Page 16 of 18 Rev D 3/06 GM
OneTouch/Elite Combination Operation Instructions
Warning: Please consult your physician before using. If you are pregnant, elderly, have high
blood pressure, diabetes, suffering from heart disease, intoxicated, or not in good health, do not
use this steam bath.
1. The Elite control functions will remain the same but the OneTouch acts ONLY as an on/off switch.
Refer to the Elite operation instructions, which are included with the control.
2. When the OneTouch is turned on, it sends a signal to the Elite turning it on and loading the last time
and temperature settings.
3. When the Elite is turned on, it will operate like normal but will send a signal to the OneTouch turning it
on and display the current time setting.
Powerflushing Your Steam Generator
1. Power on the control and set the timer to 45 minutes. Open the powerflush ball valve located on top
of the generator (refer to Figure 1) for 5-7 minutes, then close. Allow generator to finish the 45-minute
session. See following document for more detail about powerflushing.
** ThermaSol recommends one powerflush cycle after every fifty uses. **
Warning: IT IS IMPORTANT THAT NO ONE BE INSIDE THE SHOWER ENCLOSURE
DURING THE POWERFLUSH CLEANING CYCLE. IT IS ALSO IMPORTANT THAT THE
ENCLOSURE DOOR BE CLOSED DURING THIS CYCLE.
Warning: Exit shower area once the powerflush is started, hot water from Steamhead can burn
you. Keep the steam door on the enclosure closed during this cycle.
Headquarters & Technical Support
2255 Union Place, Simi Valley, CA 93065 – [phone]
Mon – Thur 7:00 – 5:00, Fri 8:00 – 12:00 PST
Eastern Sales Office
26 Industrial Avenue, Fairview, NJ 07022 – [phone]
Mon – Thur 7:00 – 5:00, Fri 8:00 – 12:00 EST
www.thermasol.com
Note: Actual remote graphics may differ.

DOC NO. 81078 Page 17 of 18 Rev D 3/06 GM
Maintaining your Steam Generator
Manual Powerflush
Warning: Exit shower area once the powerflush is started as hot water from Steamhead can burn you. Keep
the steam door on the enclosure closed during this cycle.
1. Power on the control and set the timer to 45 minutes.
2. Open the powerflush ball valve located on top of the generator for 5-7 minutes.
3. After 5-7 minutes close the powerflush ball valve.
4. Allow generator to finish the 45-minute session.
** ThermaSol recommends one powerflush cycle after every fifty uses or at least
twice a year. **
Warning: IT IS IMPORTANT THAT NO ONE BE INSIDE THE SHOWER ENCLOSURE
DURING THE POWERFLUSH CLEANING CYCLE. IT IS ALSO IMPORTANT THAT THE
ENCLOSURE DOOR BE CLOSED DURING THIS CYCLE.

DOC NO. 81078 Page 18 of 18 Rev D 3/06 GM
CONSUMER WARNING
WARNING
DO NOT USE THIS PRODUCT UNLESS YOU HAVE CONSULTED WITH YOUR DOCTOR AND
RECEIVED WRITTEN PERMISSION TO DO SO. USE OF THIS PRODUCT MAY BE HAZARDOUS TO
YOUR HEALTH.
WARNING
NEVER ATTEMPT TO FILL AROMA RESERVOIR ON THE STEAMHEAD WHEN UNIT IS IN THE ON
POSITION. SEVERE BURNS WILL OCCUR.
WARNING
DO NOT USE THERMASOL AROMA THERAPY OILS OR SKIN CARE PRODUCTS OR ANY
PRODUCT IN CONJUNCTION WITH YOUR THERMASOL UNIT WITHOUT CONSULTING WITH
YOUR ALLERGIST OR DOCTOR BEFORE USE. THESE PRODUCTS MAY BE HAZARDOUS TO
YOUR HEALTH.
WARNING
YOUR SHOWER MAY BE A SLIP AND FALL HAZARD CHECK WITH YOUR CONTRACTOR OR
FLOORING MANUFACTURER REGARDING THE SAFE USE OF YOUR FLOORING IN A STEAM
APPLICATION. SLIPPING AND FALLING INTO THE STEAMHEAD ITSELF OR INTO THE STREAM
OF STEAM EMITTING FROM THE STEAMHEAD WILL CAUSE SERIOUS BURNS, OR PHYSICAL
INJURY.
WARNING
STEAM IS HOT! DO NOT TOUCH OR GO NEAR THE STEAMHEAD FROM THE TIME THE UNIT IS
“ON”, UP TO ONE HOUR AFTER IT HAS SHUT OFF. SEVERE BURN WILL OCCUR IF YOU COME
IN CONTACT WITH THE STEAMHEAD OR STEAM EMITTING FROM THE STEAMHEAD.
WARNING
DO NOT USE STEAM ROOM WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS, AS THIS
CAN BE HAZARDOUS TO YOUR HEALTH.
WARNING
IF YOU ARE FEELING UNCOMFORTABLE, DIZZY, FAINT, OR STARTING TO FALL ASLEEP
IMMEDIATELY EXIT THE STEAM ROOM.
WARNING
DO NOT USE STEAM ROOM IF YOU ARE UNDER THE AGE OF 16 UNLESS SUPERVISED BY AN
ADULT.