Thermoscreens Designer Series Guide

9901015-5 Page 1 of 20
DESIGNER C RANGE AIR CURTAINS
Horizontal and Vertical
INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING INSTALLATION
Thermoscreens Ltd
St. Mary’s Road Nuneaton
Warwickshire England
CV11 5AU
Email: [email protected]
Tel: [phone]
Fax: [phone]
www.thermoscreens.com

9901015-5 Page 2 of 20
UN-PACKING YOUR DESIGNER AIR CURTAIN
The following items are supplied and packaged within the boxes.
Designer Air Curtain
Horizontal or Vertical Designer Air Curtain
plus fittings
Motorised Valve
(LPHW units only)
Remote Control
Accessories
Spare M4 socket button screws
2.5mm hexagon key wrench
M10 stainless steel dome nuts (vertical unit)
M8 stainless steel dome nuts (horizontal unit)
Fixing kits (if applicable)
RJ extension lead (vertical unit)
If anything is missing or damaged please contact your place of purchase immediately.
For your records
Date of Purchase……………………………..
Place of Purchase…………………………….
Serial Number…………………………………
For warranty purposes proof of purchase is necessary so please
keep a copy of your invoice.
(All documentation supplied with each unit should be stored and kept for future reference).

4001160-5 Page 3 of 20
INSTALLATION OF YOUR HORIZONTAL APPLICATION DESIGNER AIR CURTAIN
The Designer air curtain should be surface mounted inside the doorway and not
exposed to the external environment or moist conditions. It should not be built-in
or recessed in any way.
Location
Ensure that the unit is mounted within its height specification of 1.8m to 2.75m maximum
(from floor level to the underside of the unit) with the air discharge grille positioned
nearest to the door. The air curtain should be located as close to the door opening as
possible for best performance, obstructions such as door opening devices, structural
beams etc will reduce the efficiency of the air curtain. There must be at least 200mm
clearance at the air inlet for air to enter the unit, see Figure 1. For maximum
effectiveness it is essential to ensure the width of the air curtain is slightly wider than the
width of the door.
Wall Fixing
Using the 2.5mm hexagon key wrench supplied,
unfasten and remove casing screws from the Designer
unit and carefully detach the back and inlet grille
panels. All screws should be kept safe as they will be
required later in the installation.
Before fitting the unit to the wall obtain suitable wall
fixing bolts, taking into account wall type and unit
weight (see table 1)*.
Designer horizontal air curtains are supplied with two
stainless steel wall brackets fitted to each end of the
unit. Refer to Figure 1 for mounting details. Drill the
wall accordingly and secure the unit to the wall above
the door. Ensure all fixings are correctly fitted and
tightened.
Back and inlet grille panels should only be fitted after
all functional tests have been completed and verified
(See Commissioning).
For multiple air curtains joined together over a doorway a wall bracket must be fitted at
each joining point.
* It is the sole responsibility of the installer to ensure that all the fixing points and bolts
used are suitable for the air curtain.
Attention: For stainless steel units the inlet grille and back panels are coated in an easy
to peel protective film. Please ensure all the protective film is removed before the air
curtain is put into service. For clarity, all photographs in the instructions show the
stainless steel sheet with the protective film already removed.

4001160-5 Page 4 of 20
D2000HD1500HD1000H 213016501130A(mm)
ENTERING AIR
DISCHARGE AIR
242
362
411
195
Figure 1
HORIZONTAL DESIGNER AIR CURTAIN
A + 150mm
A + 86mm
82.5 82.5
Entry Point for
Water Connections
Wall Bracket with 3 off
Holes for M8 Rawl Bolts
Bracket for units with
length greater than 2.13m
A200mm minimum
clearance
Entry Point for Electrical and
Control Connections
D2500H
2780

4001160-5 Page 5 of 20
INSTALLATION OF YOUR VERTICAL APPLICATION DESIGNER AIR CURTAIN
The Designer air curtain should be surface mounted inside the doorway and not
exposed to the external environment or moist conditions. It should not be built-in
or recessed in any way. Do not install a vertical Designer air curtain in a doorway
situation where there is likelihood, or there has been a history of, rain ingress.
Location
Prior to commencing any vertical installation it is essential to ensure the correct handing
Designer unit(s) have been selected.
The air curtain is located close to the door opening with the base plate touching the wall
(see photo below) and with the air discharge grille positioned nearest to the door (see
“Handing Guide” in Figure 2). Maximum doorway width = 1.5m per air curtain. For
maximum effectiveness it is essential to ensure the height of the air curtain is slightly
higher than the opening height of the door. Obstructions such as door opening devices,
structural beams etc will reduce the efficiency of the air curtain. There must be at least
200mm clearance at the air inlet for air to enter the unit, see Figure 2.
Floor Fixing
Using the 2.5mm hexagon key wrench supplied,
unfasten and remove casing screws from the Designer
unit and carefully detach the back and inlet grille
panels. All screws should be kept safe as they will be
required later in the installation.
Before installing the Designer unit obtain four suitable fixing bolts, taking into account
floor type and unit weight (see table 1)*. Rawlplug ®M10 Projecting Rawlbolt ® 44356
type may be suitable. For dimensional details refer to the general assembly drawing,
Figure 2.
Designer vertical air curtains are supplied with the base plate fitted. Determine and place
the unit at its most favourable position. A wall bracket must be fitted to the top of the unit
for D2000 and D2500 air curtains to tether the top of the unit to the wall. In order to use
the wall bracket supplied ensure the back of the base plate touches against the wall.
Using the base plate as a template, mark the location
of the four holes, as indicated in the adjacent picture.
Using a suitable masonry drill bit correctly drill the four
marked out holes. Place M10 fixing bolts into each
hole, ensuring all bolts are upright.
Reposition the air curtain base plate over the
projecting bolts. Tighten each M10 nut as indicated in
the adjacent picture. Ensure the vertical unit is
secure, level and square.
Base plate
touching wall

4001160-5 Page 6 of 20
Using a hacksaw carefully cut the projecting bolt flush
with the nut, ensuring the base plate is not damaged
or marked in any way.
Remove only one M10 nut and refit and secure bolt
with a stainless steel M10 dome nut supplied. Repeat
for each of the other three projecting bolts one at a
time.
Back and inlet grille panels should only be fitted after
all functional tests have been completed and verified
(See Commissioning).
Stacking Air Curtains
Only a single 1.0m stacking vertical air curtain should
be mounted on top of another vertical unit. The
maximum overall height for stacking is 2.78m (1.5m
+ 1.0m vertical). All units higher than 1.5m must be
secured with a wall bracket at the top of the stack.
Using fixing kit components supplied the vertical stack
frames are joined together using M8 x 25mm
hexagonal bolts and M8 nyloc nuts (see insert).
* It is the sole responsibility of the installer to ensure that all the fixing points and bolts
used are suitable for the air curtain.
Attention: For stainless steel units the inlet grille and back panels are coated in an easy
to peel protective film. Please ensure all the protective film is removed before the air
curtain is put into service. For clarity, all photographs in the instructions show the
stainless steel sheet with the protective film already removed.

4001160-5 Page 7 of 20
D2500VD2000VD1500V 278021301650A(mm)
View 'A' View 'B'
As Drawn for L.H. Opposite Hand for R.H.
DOORWAY
RH
LH
View 'A'
View 'B'
OR
A
340
Foot Plate
460
Foot Plate
362
242
75
Figure 2 VERTICAL DESIGNER AIR CURTAIN
OUTSIDE
DISCHARGE AIR
INSIDE
ENTERING AIR
49
49
"Handing Guide"
3 Holes for M8
Distance between hole
centres 82.5mm Bolt Holes for M8
Rawl Bolts - 3 off
Wall Bracket for
D2000V & D2500V
Bolt Holes for M10
Rawl Bolts - 4 off
Entry Point for Water and Electrical Connections
if entry via floor void
Entry Point for Water, Electrical
and Control Connections
200mm minimum
clearance
1.5m max.
Air
inlet
Air
inlet

4001160-5 Page 8 of 20
Safety and Electrical Connections
All electrical wiring and connections MUST be carried out by a competent qualified
electrician in accordance with the latest edition of the IEE wiring regulations and/or
local statutory regulations.
A single phase or 3 local phase isolator with a contact separation of at least 3mm in all
poles must be fitted to the supply wiring (the isolator must be fitted in an accessible
position).
The air curtain must be earthed.
The appliance must be connected by means of wires
having an appropriate temperature rating (heat resistant)
(electric models only). Electrical connection entry point
for horizontal Designer air curtain is from the left hand
side of the unit, refer to Figure 1. Figure 2 and the
adjacent picture details optional electrical connection
entry points for vertical Designer models. Power and
control cables for vertical units should be separately
threaded up via the cable trunking provided (see insert).
Ensure that the supply cables, circuit breakers and other electrical installation
equipment are correctly sized for the air curtain being installed; see Table 1.
On a 3 phase electrical supply the unit requires a neutral connection (3N~).
Cable glands used for the Electrical Input must be rated IP21 or higher.
Table 1
Air Curtain Electrical
Supply
(V/ph/Hz)
Rated Power
Input (kW) Current per phase (A) Heat Output (kW) Weight (kg)
D1000A 230/1/50 0.15 0.7 N/A 30
D1500A 230/1/50 0.20 0.9 N/A 43
D2000A 230/1/50 0.25 1.1 N/A 59
D2500A 230/1/50 0.35 1.6 N/A 73
D1000W 230/1/50 0.15 0.7 6.0 31
D1500W 230/1/50 0.20 0.9 9.0 44
D2000W 230/1/50 0.25 1.1 12.0 60
D2500W 230/1/50 0.35 1.6 15.0 75
D1000E 400/3/50 9.15 13.7 4.5/9.0 32
D1500E 400/3/50 12.20 18.3 6.0/12.0 45
D2000E 400/3/50 18.25 27.2 9.0/18.0 62
D2500E 400/3/50 21.35 32.0 10.5/21.0 77
Optional Electrical
Connection Entry Points

4001160-5 Page 9 of 20
LPHW Models
For LPHW models ensure suitable water mains isolation valves are fitted in the flow and
return pipework. When fitting the 3-port valve ensure that the pipe connections are
fitted as detailed below and are in accordance with the manufacturers leaflet supplied
with the valve.
Designer vertical LPHW stacked units will be supplied with a suitable pipe connecting kit
and balancing valves to ensure heat output is even over the whole height of the air
curtain.
Air Curtain Water Flow Rate (l/s)
82/72 °C Coil Water Pressure Drop (kPa)
D1000W 0.14 2.77
D1500W 0.21 6.74
D2000W 0.29 13.40
D2500W 0.35 15.20

4001160-5 Page 10 of 20
Fitting/Connecting the Remote Control
The Ecopower Plus controller uses extra low voltage to communicate via the RJ control
cable supplied. The controller should be located in a suitable place for easy access, it
can be fixed to the wall via various fixing slots
provided in the back case or onto an electrical
switch box (not provided). To mount controller
onto an existing switch box, feed one end of the
control cable through the switch box (see insert).
Using a screwdriver undo screw mounted on
the top of the controller case. Pull the front case
slightly forwards and lift the back case away.
Feed and secure the RJ control cable through
one of the openings in the back case and
secure back case to switch box using 2 x M3.5
mounting screws (not provided).
With the cable RJ plug locking clip lying nearest
to controller PCB, connect the RJ plug to the RJ
socket on the board.
Note: For controller DIP switch options refer to
Ecopower Plus Remote Control Operation and
DIP Switch Settings.
Refit the controller front case to the back case.
The air curtain end of the control cable should be
connected to one RJ socket fitted either on the
top panel for NT or the Ecopower motherboard
inside a recessed air curtain. Ensure the control
cable is safely secured.
The remote control is supplied with 6m of cable and
a pre-fitted connecting plug. Ensure the remote
control cable is safely secured and connected. For
vertical Designer an extension lead with an in-line
connector is supplied for threading the control cable
within the unit (see insert). Control
cable
Power
cables

4001160-5 Page 11 of 20
Multiple Installation
To Master/Slave two or more air curtains together, or if there are two air curtains in a
vertical stack, the remote control is plugged into the first unit (the Master) and a RJ
extension lead then connected from the Master to the Slave unit(s).
Horizontal application air curtains, up to a maximum of eight units, may be connected as
indicated below. Thermoscreens 3m RJ extension leads are available and should be
ordered separately.
For horizontal Master/Slave configuration an independent mains supply as per Table 1
must be supplied to each air curtain.
The maximum height for a vertical stack
is 2.78m (1.5m + 1.0m vertical). An RJ
extension lead and in-line RJ connector
is supplied with vertical stack units.
Ensure all incoming electrical mains
supply cables are suitable for the total
power rating of the air curtain stack
(see D2500).
Electrical Mains
Supply
Electrical Mains
Supply
Electrical Mains
Supply
RJ Cable RJ Cable
Services entry
either from bottom
or side

4001160-5 Page 12 of 20
Ecopower Controller Motherboard
Function Control Comments Standard
Fan Heat Interlock –
The heat output is governed by the
fan speed. If low or medium fan
speed is selected the heat output
will operate on only first heat stage.
Second stage heating will only
operate on high fan speed.
DIP1 Option Suitable on vertical electrically
heated Designer air curtain.
Maximum heat output achieved if
maximum fan speed selected.
Independently set-up DIP switch
on each mother board. This
feature operates in manual or
auto mode.
As supplied, the
default setting would
be for heat and fan
settings to be
independent (DIP1
OFF).
Disable Fan Run-on –
Disable fan run-on.
DIP2 Option
(LPHW &
Ambient only)
Must only be used for LPHW and
Ambient air curtains.
Independently set-up DIP switch
on each mother board.
As supplied, the
default setting would
enable fan run-on
(DIP2 OFF).
Thermostat Master –
Only the air sensor thermistor in
the master air curtain will be used
for measuring the reference air
temperature for the whole
master/slave installation.
DIP3 Option The air sensor thermistors in all
the slave air curtains will be
ignored. This will then avoid
situations on larger doorways with
master/slave air curtains where
some units can blow cold air
whilst others can blow warm air,
because they currently all refer to
their own air sensor for control of
the heat output of each air
curtain.
The master air curtain need not
be the one that the wall control is
plugged into. This dip switch
setting must also be used for
Global Switching (Master/Slave)
via the INHIBIT terminal – see
next page.
As supplied, the
default setting would
be for the air sensor
thermistor on all
units to be
measuring
(DIP3 OFF).
Overheat Fan Disable –
If DIP4 is on and thermal cut-out(s)
operate both heat and fan circuits
are isolated and LED’s on wall
switch flash. If DIP4 is off and
thermal cut-out(s) operate, only the
heating circuit is isolated and the
LED’s on the wall switch flash.
DIP4 Option
(Electric only) Independently set-up DIP switch
on each mother board.
To remove fault, isolate electrical
supply to air curtain, reset TOC
and reconnect supply.
As supplied, the
default setting would
enable fan if TOC
trips (DIP4 OFF).
Fan run-on time set two minutes. Built-in If “FAN ONLY” has been
selected, at switch off, no fan run-
on.
-white rectangle indicates the moveable head of each 4 way DIP switch
DIP switches fitted on the Ecopower board provide a selection of optional features as
described above. Isolate and switch electrical power off before configuring and/or
changing any DIP switch settings.
ON
OFF
1 2 3 4
ON
OFF
1 2 3 4
ON
OFF
1 2 3 4
ON
OFF
1 2 3 4

4001160-5 Page 13 of 20
Easy plug-in arrangement for remote air sensor thermistor on a 1m lead. Plugging-in
the remote air sensor to J3 disables the standard air sensor thermistor already fitted
on the Ecopower board. As supplied, the board will not have the remote air sensor
fitted.
An INHIBIT two screw terminal fitted on the Ecopower board for BMS remote On/Off
feature. If the terminal is linked, i.e. by 2 wires to a remote volt free contact, the unit will
run. If it is open circuit across the terminal the unit will switch off. This remote On/Off
feature has global switching logic, i.e. if you master/slave several units together you
need connect the remote contact to only one of them to turn all units on and off in the
master/slave system. For global switching to work on the slave units, need to set DIP3
Option (see previous page) on the unit that the remote contact is wired to and have
previously turned the unit on with the wall switch. As supplied, a wire link will be fitted
to the terminal block on every unit. For summer settings place a 3.3kΩresistance
across the INHIBIT terminal, with these settings fans only will run even if controller is
requesting for heat.
ECOPOWER BOARD
Customer Building Management System
A HEALTHY two screw terminal is included on the board for a fault signal indication if
the electric elements overheat cut-out has operated. A healthy system provides a 24V
DC signal at the terminals compared to an overheat fault which provides OV DC.

4001160-5 Page 14 of 20

4001160-5 Page 15 of 20

4001160-5 Page 16 of 20

4001160-5 Page 17 of 20
Ecopower Plus Remote Control Operation and DIP Switch Settings
On/Off (I/O)
Press On/Off switch (1) to turn the air curtain
On and operate as follows:-
Press Auto switch (2) to cycle between Manual
and Automatic modes. The Auto on indicator
LED is lit for "Auto Mode" and un-lit for "Manual
Mode".
Manual:
Heat output can be selected as Zero, Half Heat
or Full Heat. Heating levels are selected by
stepping up or down with switches (3) and (4).
Heating level indicator LED's go 0%, 50% or
100% to show the level selected.
Automatic:
If DIP switches 1, 2 and 4 on the Ecopower
motherboard are set to OFF, the air curtain
measures the incoming air temperature and
automatically selects the necessary amount of
heat to keep it at the level selected.
Fan Speed
Switches (5), (6) and (7) select fan speed low,
medium or high respectively. The appropriate
LED above each fan speed indicator is
illuminated to show which fan speed is selected.
Pressing the On/Off switch (1) again switches the
air curtain off with all the LED’s switched off. If a
heated air curtain is heating when switched off
the fan will run-on at low fan speed for an
extended time (approx. 2 minutes) to dissipate
excess heat.
DIP Switch Settings
At the back of the Ecopower Plus remote
control PCB there are four DIP switches (see
above) that provide the following optional
features.
DIP1 Restart on Power-Up – If electrical
supply to the air curtain is
interrupted, upon restoring electrical
supply, the customer’s settings on
the remote control will be retained.
The default is with this feature ON.
DIP2 Stop Fan on Cold – Fans switch off
when heating level is achieved
(Automatic mode only). The default
setting is with this feature OFF.
DIP3 Never Blow Cold – Unit always
heats in Automatic mode (i.e. will
not go to ambient mode). The
default setting is with this feature
OFF.
DIP4 Air Sensor in Controller – The air
sensor in the remote controller is
enabled (DIP4 ON) and the air
sensor on the Ecopower
motherboard in the air curtain is
disabled. Temperature control for
Automatic Mode is then done at the
remote control, which may be an
advantage to limit overheating of the
door entrance area. The default
setting is with this feature OFF.
Do not switch the air curtain On/Off from the isolator. If the mains supply is
isolated or cuts-out during operation the safety thermal cut-out(s) for electric
heated air curtains within the air curtain may operate. If this happens the
thermal cut-out(s) will need to be reset by a competent technician.
2
1
3
4
5
6
7
Heating Level
Scale

4001160-5 Page 18 of 20
Commissioning
With the casing still removed confirm the air curtain fans operate correctly and there is
no excessive mechanical noise coming from the fans. Check that the fans operate at
Low, Medium and High speeds, except for Electric Heated Vertical units which only
operate at High speed. Use the gate valves to balance heating output evenly across the
whole air curtain for D2500V LPHW air curtains that have two heating coils. If the unit is
electric heated or water heated check that the air stream from the discharge grille
warms up across the whole length of the air curtain when heating is selected. On
D2500W water heated stacked units it may be necessary to adjust the balancing valves
at the bottom of the air curtain to get even heat output over the whole height of the unit.
Check that heating increases as higher heat is selected and feel to see that the warm
air stream is reaching across the doorway with door open or closed. Verify the
operation of the Ecopower controller in Manual Mode. Then select Auto Mode and
increase the heating set point until the air stream warms up. Reduce the heating set
point until the air stream goes cold.
Explain to the end user that the doorway should be closed whenever possible but that
during times of high pedestrian use it will become effectively ‘open doorway’. The air
curtain serves an essential purpose by saving energy and providing comfort to the
occupants when compared to an open doorway with no air curtain fitted.
Once all functional tests have been carried out and the air
curtain operates satisfactorily, firstly hook and locate the
back panel around the fixing tabs closest to the outlet grille.
Ensure all fixing holes are correctly aligned with tab inserts.
Fit and align the two locating pins on the inlet panel with
corresponding back panel holes (see insert). Secure both
panels using the 26 x M4 socket button screws removed
earlier in the installation process.
Before leaving site it is important that the air curtain
installation is “Handed-Over” to the end user or his
representative and the operation of it is fully explained and
that they understand how it operates. Explain also the
service intervals and that the unit must be regularly cleaned.
Fault Conditions
In the event of a fault the thermal cut out(s) on electric
heated units (Note: If the mains supply is isolated
during operation then the thermal cut outs may
operate) or internal fuses may operate. The thermal
cut out(s), one on the 1m/1.5m models and two on the
2m model, are located behind the hole marked with a
red ring label (see insert).
For Ecopower units two internal electrical fuses are
located on the Ecopower board; 6.3A (T) supplies the fan
motors within the air curtain and 125mA (F) controls the operation of the Ecopower
board. If for an electric heated air curtain an overheat fault occurs, or if J2 link is
missing for LPHW models, the LED’s on the remote control will flash and the Ecopower
board status LED on the board will be permanently red to indicate a fault.
In the case of a fault condition (refer to flowchart) do not attempt to reset the thermal cut
outs or replace the fuses, arrange for a Thermoscreens appointed technician or certified
electrician to attend the unit to investigate the reason why the thermal cut outs/fuse(s)
have operated. Once the cause has been determined and rectified, they will reset the
thermal cut out and/or replace the fuse and check the operation of the unit.
Locating Pins

4001160-5 Page 19 of 20
PCB Status
Fitted on the PCB board inside of the air curtain is an LED shown as LED1 on wiring
diagrams that will indicate the Ecopower control status.
1. LED flashing green – operation normal.
2. LED flashing red – low supply voltage or controller not plugged into Ecopower
motherboard.
3. LED permanently red – thermal cut outs open circuit (electrically heated models) or
J2 link missing (LPHW models). Remote Control LED’s will also flash to indicate the
thermal cut-out(s) has operated or J2 link is missing. Refer to Fault Conditions above
detailing how to reset thermal cut-outs.
User Fault Finding Flowchart
Yes
Unit is working
satisfactorily
Switch on
Electrical Power
Connect remote
control and push
On/Off switch to turn
unit
on
Select heat output
Contact Installer
Service Agent to
investigate why
thermal cut-out(s)
have operated
Service Agent to
reset thermal cut-
out(s)
Contact Installer
Yes
No
Yes
Yes
No
No
No
Yes Yes
No
No
Is Electrical
Power
switched on
Are the fans
operating
correctly
Is the unit
discharging
warm air
Check if
thermal cut-
out(s) have
tripped
Do the
LED’s light
up on the
remote
control
Is the
remote
control
plugged in
and turned

4001160-5 Page 20 of 20
Service & Maintenance
Always disconnect and isolate the mains electricity supply before installing,
maintaining or repairing this equipment. Note: All maintenance/repairs should
only be carried out by a competent electrician or Thermoscreens appointed
technician.
To ensure the air curtain operates at full efficiency the back and inlet grille panels, fan
impellers, housings and motors must be kept free of dust and debris. Build up of dust
on the fan impellers can cause vibration, noise and excessive wear on the motor
bearings.
Frequency of cleaning will depend on the environment, but we would recommend that
the unit be cleaned a minimum of every 3 months (failure to adequately maintain the
unit and provide a suitable cleaning schedule will result in performance degradation
and reduce the life expectancy of the air-curtain).
Remove the back and inlet grille panels from the air curtain. Vacuum and clean the
build-up of dirt and debris within the air-curtain (please note that the motor(s) are
permanently lubricated and require no additional lubrication).
Once the air curtain has been cleaned check all electrical connections within the unit
ensuring terminals are tight and that crimped connections have not become loose.
Re-install the back and inlet panels. Reconnect the electrical supply and fully function
test the air-curtain to ensure correct operation (See Commissioning).
Warranty
If any problems are encountered, please contact your installer/supplier. Failing this
please contact the Thermoscreens warranty department. All units are covered by a two
year warranty period.
Care has been taken in compiling these instructions to ensure they are correct, although
Thermoscreens disclaims all liability for damage resulting from any inaccuracies and/or
deficiencies in this documentation. Thermoscreens retain the right to change the
specifications stated in these instructions.
Thermoscreens Ltd
St. Mary’s Road Nuneaton
Warwickshire England
CV11 5AU
Email: [email protected]
Tel: + 44 (0) 24 7638 4646
Fax: + 44 (0) 24 7638 8578
www.thermoscreens.com