Thermrad LINA User manual

USER MANUAL
LINA
29.04.2013 Rev:00
www.thermrad.nl
• To clean the product, use a piece of cloth, slightly wetted with (hot) water
• DO NOT use harsh chemicals, cleaning solvents, bleaches or strong detergents
• DO NOT use in open air environments and environments where the air temperature is
below 0°C or above 95°C. When the water within the radiator freezes, it may cause
problems.
• The product is reliable for a maximum working pressure of 6 bar. DO NOT use the product
above this maximum limit.
• PH-value of the water used in the system should be between 6 and 9.
• Artificially softened water should not be used in stainless steel radiators.
• Once fixed and connected, the system should be properly flushed and filled in order to
remove debris, sludge, solid particles and chemical residues, which may cause corrosion
and damage within the system. A good water treatment inhibitor should be used within
the system to avoid corrosion and sludge.
• When the air is trappet within the radiator, it may cause inefficient warming.
• Storage area should be clean, dry, closed and away from chemical solvents. Solvent filled
Electric Radiators should be stored above 0°C.
• Producer offers 10 (ten) years guarantee for STAINLESS STEEL RADIATORS, when
installed on CLOSED SYSTEMS.
• Producer shall not be liable for any violation to intellectual property rights of the goods
and the compliance of the goods with rules and regulations of the countries, where the
goods are sold.
www.thermrad.nl
CARE AND MAINTENANCE

USER MANUAL
1
4
4
4
4
3
Required Material
Installation
Suitable Valves
Screwdriver
Electric drill
Drill Bit (8 mm.)
Spirit level
Allen key (3 mm) (F)
Stepladder (if required)
Air vent 1/2 "
Wall Plug
Wall Mounting Bracket
Screw Ø 6mm. x 50 mm.
Socket head screw (M6 x 6)
Blind plug 1/2”
A
B
C
D
E
Symbol Pcs
K
H
W
H
D
min - max
57-82 mm
Min. 125 mm
By (Bracket Centers )
Bg
K1
B
A
E
F
DC
Assembly Instructions
Gently pull the radiator out of its box and cover.
Sufficient PTFE tape must be applied to valve-tail
threads prior to their installation.
Using a spirit level, mark the position of the brackets
according to where the radiator is to be fixed.
Mark the centers of the brackets on the brick wall (C).
Drill four 8 mm diameter holes to a minimum depth of
60mm & insert wall plugs (B).
Screw brackets (C) into wall plugs (B) with 6mm
diameter x 50mm screws (D).
Slide the pins into the wall mounting brackets (C) and
secure in position by tightening the socket head
screws (E) with allen key (F).
Check if the radiator is mounted perfect, otherwise slide
the radiator from the mounting brackets.
Install the radiator minimum 12,5 centimeters above
the ground.
Connect the radiator to the heating circuit.
Width
Height
Depth
min - max
Pipe Center (Valve)
Bracket Centers
Tube
Quantity
Weight
HEAT CAPACITY
90/70/20 °C
W
H
D
K
K
1
Bg
By
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(pcs)
(kg)
Kcal/h
Watt
Btu/h
500
1200
73-98
468
50
468
1020
18
7.30
290
337
1150
600
1200
73-98
568
50
568
1020
18
8.10
331
385
1313
500
1600
73-98
468
50
468
1420
23
9.30
374
435
1484
600
1600
73-98
568
50
568
1420
23
10.40
426
495
1689