Hunter Illumi-Heat Service manual

Form# 43566-01
20100625
©2010 Hunter Fan Co.
English Español
Illumi-Heat™
Light & Heat on Demand™
Illumi-Heat™
Light & Heat on Demand™
Illumi-Heat™
Light & Heat on Demand™
Owner’s Guide and Installation Manual
Manual De Propietario

WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, OBSERVE THE
FOLLOWING:
BEFORE BEGINNING, DISCONNECT THE
POWER SUPPLY AT THE BREAKER BOX.
FAILURE TO DO SO CAN RESULT IN
SERIOUS INJURY OR DEATH
• Be cautious! Read all instructions and safety information before installing your new
Illumi-heat semi-flush fixture. Carefully review the assembly illustrations.
• Use this unit only in the manner intended.
• All wiring must be in accordance with national and local electrical codes. If you are unfamil-
iar with wiring, you should use a qualified electrician.
• Before you begin installing the fixture, switch power off at the correct breaker, turn on the
bulb switch to make sure breaker handle was sitting on the right position, and lock the breaker
box to prevent power from being switched on accidentally during installation. When the breaker
box cannot be locked, securely fasten a prominent warning device such as a danger tag to the
breaker box.
• To reduce the risk of fire, electric shock, or personal injury this fixture must be mounted as
marked.
• Only use this fixture with the transmitter supplied by Hunter.
• Mounting structure must be capable of supporting this product weight of 9.0 lbs.
READ AND SAVE THESE INSTRUCTIONS
Turn off the power source.
!
2
43566-01 • 06/25/10 • Hunter Fan Company

Tools Needed (not supplied)
Glass Dome
Bottom Finial
Wire Connectors (3)
(not to scale)
Verify all parts were in the box before installing.
Flat head screwdriver Phillips screwdriver
Transmitter and
Transmitter Holder
(not to scale)
Needle-nosed Pliers
Wires:
Black, White, Copper (Ground)
Receiver
Canopy
Hanger Bracket
Threaded Rod
Light Sockets (3)
Heater/Light Fixture
Top Finial
3
43566-01 • 06/25/10 • Hunter Fan Company
Parts

Top View of Fixture
If you are going to install more than one Illumi-Heat in your home, then you will need to assign
each unit a its own unique Transmitter / Receiver Code.
1) Looking at the fixture from its top, locate the Receiver, as shown in Figure 1.
Figure 1 - Receiver
2) On the Receiver you will see the four switches that you will use to set the code for the
Transmitter and the Receiver. See Figure 2.
ON DIP
   
ON DIP
   
Figure 2 - Receiver Code Switches
Switches
NOTE - All Switches are
shown in the ON position
ON DIP
   
Receiver
(Bracket cut away
for clarity.)
4
43566-01 • 06/25/10 • Hunter Fan Company
Pre-Installation for Multiple Illumi-Heat Units in Your Home

3) Configure the Receiver Switches to your desired code. Make a note of which Receiver
Switches you turned On and turned Off. NOTE: Make certain each Receiver is assigned a
different code.
4) Remove the Transmitter Battery Compartment door as shown in Figure 3.
Figure 3 - Remove Transmitter Battery Compartment Door
5) For every Receiver Code Switch you turned Off, use a pair of needle-nosed pliers to
carefully remove its corresponding Connector from the Transmitter Terminals. See Figure 4.
For instance, if you turned Off Receiver Switches 1 and 3, then you would remove
Connectors 1 and 3 from the Transmitter.
1234
Transmitter Battery
Compartment Door
Transmitter Terminals
Connector
Figure 4 - Transmitter Terminals and Connector
5
43566-01 • 06/25/10 • Hunter Fan Company
Pre-Installation for Multiple Illumi-Heat Units in Your Home (Continued)

Figure 5 - Attach Hanger to Electrical Box
1) If you are replacing an existing light fixture, disconnect and remove the old fixture and
hanger bracket, leaving the exposed wires coming from the electrical box.
2) Attach the Hanger Bracket assembly to the electrical box as shown in Figure 5.
Hanger Bracket
Electrical Box
6
43566-01 • 06/25/10 • Hunter Fan Company
Installation

3) Suspend the fixture by placing the Cable Loop over the Cable Loop Hanger. See Figure 6.
Figure 6 - Suspend the Fixture
Figure 7 - Ground Screw
Cable Loop Hanger
Cable Loop
7
43566-01 • 06/25/10 • Hunter Fan Company
4) Use UL-approved wire connectors to connect the wires, black-to-black, white-to-white. Loop
the ground wires around the Ground Screw, then tighten the Ground Screw. See Figure 7.
Ground Screw
Installation (Continued)

5) Swing the Fixture up so that the threaded rod exits the hole in the bottom of the canopy.
See Figure 8.
Figure 8 - Positioning the Fixture
Swing fixture up
INSTALLATION continued
Threaded Rod
NOTE: For clarity, the
electrical box and wires
have been omitted from
this illustration.
Canopy
8
43566-01 • 06/25/10 • Hunter Fan Company
Installation (Continued)

6) Position the top finial over the threaded rod, and tighten the top finial until tight. See
Figure 9.
Figure 9 - Top Finial Nut Installation
INSTALLATION continued
Figure 10 - Install Light Bulbs
7) Install three 40-watt Candelabra light bulbs (not included) as shown in Figure 10.
40-watt Candelabra Light Bulbs (not included)
Top Finial
Threaded Rod
9
43566-01 • 06/25/10 • Hunter Fan Company
Installation (Continued)

INSTALLATION continued
Figure 11a Figure 11b
Heater
Glass Dome
9) Position the Bottom Finial over the Glass Dome as shown in Figure 12, and twist it clock-
wise until tight.
Figure 12 - Install Bottom Finial
Glass
Bottom Finial
8) Position the Glass Dome under the Heater/Light Fixture as shown in Figure 11a. Then,
place the Glass Dome over the Heater/Light Fixture as shown in Figure 11b.
Install Glass Dome
10
43566-01 • 06/25/10 • Hunter Fan Company
Installation (Continued)