thomann E-800 User manual

E-800
power amplifier
user manual

Musikhaus Thomann e.K.
Treppendorf 30
96138 Burgebrach
Germany
Telephone: [phone]
email: [email protected]
Internet: www.thomann.de
25.01.2012

Table of contents
1 General notes............................................................................................................................................... 4
2 Safety notes.................................................................................................................................................. 7
3 Installation and operation.................................................................................................................. 12
4 Connectors and controls...................................................................................................................... 19
5 Technical data........................................................................................................................................... 25
6 Protecting the environment.............................................................................................................. 27
Table of contents
E-800
3

1 General notes
This user manual contains important information on the safe operation of the device. Read and
follow all safety notes and all instructions. Save this manual for future reference. Make sure
that it is available to all persons using this device. If you sell the device to another user, be sure
that they also receive this manual.
Our products are subject to a process of continuous development. We therefore reserve the
right to make changes without notice.
This section gives an overview of the symbols and signal words used in this user manual.Symbols and signal words
General notes
power amplifier
4

Signal word Meaning
DANGER! This combination of symbol and signal word
indicates an immediate dangerous situation
that will result in death or serious injury if it is
not avoided.
CAUTION! This combination of symbol and signal word
indicates a possible dangerous situation that
can result in minor injury if it is not avoided.
NOTICE! This combination of symbol and signal word
indicates a possible dangerous situation that
can result in material and environmental
damage if it is not avoided.
Warning signs Type of danger
Warning – high-voltage.
General notes
E-800
5

Warning signs Type of danger
Warning – danger zone.
General notes
power amplifier
6

2 Safety notes
Use the device only as described in this user manual. Any other use or use under other oper‐
ating conditions is considered to be improper and may result in personal injury or property
damage. No liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sufficient physical, sensorial, and intellectual
abilities and having corresponding knowledge and experience. Other persons may use this
device only if they are supervised or instructed by a person who is responsible for their safety.
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from
the unit. They could swallow the pieces and choke!
Never let children unattended use electrical devices.
Intended use
Safety
Safety notes
E-800
7

DANGER!
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never
remove any covers.
There are no user-serviceable parts inside.
DANGER!
Electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord) with a pro‐
tective contact plug. Do not modify the mains cable or the plug. Failure to do so
could result in electric shock/death or fire. If in doubt, seek advice from a regis‐
tered electrician.
Safety notes
power amplifier
8

CAUTION!
Possible hearing damage
With loudspeakers or headphones connected, the device can produce volume
levels that may cause temporary or permanent hearing impairment.
Do not operate the device permanently at a high volume level. Decrease the
volume level immediately if you experience ringing in your ears or hearing
impairment.
NOTICE!
Risk of fire
Do not block areas of ventilation. Do not install the device near any direct heat
source. Keep the device away from naked flames.
Safety notes
E-800
9

NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never
expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and
strong vibrations.
NOTICE!
Power supply
Before connecting the device, ensure that the input voltage (AC outlet) matches
the voltage rating of the device and that the AC outlet is protected by a residual
current circuit breaker. Failure to do so could result in damage to the device and
possibly injure the user.
Unplug the device before electrical storms occur and when it is unused for long
periods of time to reduce the risk of electric shock or fire.
Safety notes
power amplifier
10

NOTICE!
Magnetic fields
The device generates strong magnetic fields that can interfere with the function
of poorly shielded devices. The strongest magnetic fields are directly above and
below the power amplifier. Therefore, never place sensitive devices such as pre-
amplifiers, radio transmission systems, or tape decks directly above or below the
power amplifier. When installing the power amplifier into a rack, you should place
it in the lowest position, and further equipment such as pre-amplifiers in the
highest position.
Safety notes
E-800
11

3 Installation and operation
Unpack and check carefully there is no transportation damage before using the unit. Keep the
equipment packaging. To fully protect the device against vibration, dust and moisture during
transportation or storage use the original packaging or your own packaging material suitable
for transport or storage, respectively.
Establish all connections as long as the unit is switched off. Use the shortest possible high-
quality cables for all connections.
DANGER!
Electric shock caused by high voltages at the power amplifier output
The output voltages of modern high-performance amplifiers may result in death
or serious injury.
Never touch the bare ends of loudspeaker cables when the amplifier is on.
Installation and operation
power amplifier
12

NOTICE!
Magnetic fields
The device generates strong magnetic fields that can interfere with the function
of poorly shielded devices. The strongest magnetic fields are directly above and
below the power amplifier. Therefore, never place sensitive devices such as pre-
amplifiers, radio transmission systems, or tape decks directly above or below the
power amplifier. When installing the power amplifier into a rack, you should place
it in the lowest position, and further equipment such as pre-amplifiers in the
highest position.
Installation and operation
E-800
13

Balanced female XLR panel connectors are used for the signal inputs. Male XLR panel connec‐
tors are used for the signal outputs The figure and the table show the XLR pin assignment.
1 Ground
2 Signal (+)
3 Signal (–)
The figure and the table show the pin assignment of the ¼-inch (6.35-mm) jack plugs (unbal‐
anced and balanced).
XLR connectors for signal inputs
and outputs
Jack plug for signal inputs and
outputs
Installation and operation
power amplifier
14

1 Signal
2 Ground
1 Signal (+)
2 Signal (–)
3 Ground
The following figure shows the pin assignment of the lockable speakON panel connector.speakON connector for loud‐
speaker connections
Installation and operation
E-800
15

Installation and operation
power amplifier
16

Depending on the individual application, the amplifier can be used in different operation
modes:
Stereo mode
The two amplifier channels operate independently of one another, either
channel (A and B) is amplified and connected to loudspeakers, the volume can
be controlled separately for the two outputs.
Parallel mode
The two amplifier channels receive the same input signal from channel A and
loudspeakers are connected to each amplifier, the volume can be controlled
separately for the two outputs.
Bridged mode
The two amplifier channels are internally connected in such a way that twice
the output power is available. Only the input signal from channel A is amplified
and loudspeakers are connected only to the correspondingly marked output.
The volume is controlled via the control knob for channel A.
Possible operation modes
Installation and operation
E-800
17

For each output of the amplifier, the total impedance resulting from the loudspeakers con‐
nected to it must not be below the allowed minimal impedance of the amplifier output. If you
connect more than one loudspeaker to an amplifier output, please note the following:
nIf the loudspeakers are connected in a series, the individual impedances will be added up.
nIf the loudspeakers are connected in parallel, the reciprocal of the total impedance equals
the sum of the reciprocals of the individual impedances.
Example: If you have two loudspeakers with the same impedance, their impedance doubles if
they are connected in a series, their impedance halves if they are connected in parallel.
For detailed information related to this topic please refer to our Online Guide ‘PA Speakers’
(www.thomann.de).
The device has been designed for rack mounting in a standard 19-inch rack; it occupies two
rack units.
Rack mounting
Installation and operation
power amplifier
18

4 Connectors and controls
Front panel
Connectors and controls
E-800
19

1 POWER
Power on/off switch. Switches the device on and off.
2 LED panel
SIG Indicates the presence of an input signal.
CLIP Lights under the following conditions:
nChannel overdrive.
In this case, reduce the volume until the LED turns off.
nShort-circuit at the output.
Immediately turn off the device, fix the short-circuit and turn on the device again.
PRO Lights under the following conditions:
nThree to five seconds after turning on or off when the device is in an unstable state.
nThere is no loudspeaker connected.
nThe temperature of the amplifier blocks has reached 85°C.
nOne or more protection circuits have been triggered or the device is defective.
Connectors and controls
power amplifier
20