THOMSON ROC 850 - AVEC CODES User manual

ROC850
ROC850_COV 26/09/03 16:42 Page Cov1
User manual

ROC850
2
1
3
4
11
10
6
5
9
7
8
FLAP_COVER 29/09/03 15:29 Page 1

1
Contents
EN
EN
General
Precautions of use ....................................................................................................................................................................2
About your remote control
Your ROC 850 includes many features........................................................................................................................................3
Installing the batteries..............................................................................................................................................................4
About the batteries ..........................................................................................................................................................................4
Description of keys and LED....................................................................................................................................................5
Description of the touch screen keys......................................................................................................................................6
Other very useful touch screen keys ..........................................................................................................................................7
Programming the ROC 850
Programming by entering a 3-digit code................................................................................................................................8
Programming using the Brand scan method ........................................................................................................................9
Programming using the auto scan method..........................................................................................................................10
Identifying codes found during scanning ..............................................................................................................................11
Programming a Macro
Programming without timeout ............................................................................................................................................12
Programming with timeout between 2 keys........................................................................................................................13
Using a Macro-command ......................................................................................................................................................13
Removing a Macro ..................................................................................................................................................................13
Zapping between 2 channels
Programming ..........................................................................................................................................................................14
Use (zap between 2 channels) ..............................................................................................................................................14
Customizing the touch screen
Returning to the default screen ............................................................................................................................................15
Learning a code
Before starting, read the following tips ................................................................................................................................16
Instructions for downloading keys ........................................................................................................................................17
To clear all the keys downloaded in a given mode..............................................................................................................17
Other functions
Beep....................................................................................................................................................................................................18
Backlighting ......................................................................................................................................................................................18
Zero reset ........................................................................................................................................................................................18
Scanning the channels ....................................................................................................................................................................18
Showview/VideoPlus+ ....................................................................................................................................................................19
General Off ......................................................................................................................................................................................19
Sound volume of a TV set ............................................................................................................................................................19
Sound volume of a satellite or cable receiver..........................................................................................................................19
Sleep Timer ......................................................................................................................................................................................19
Troubleshooting
If the remote control does not operate ..............................................................................................................................20
ROC850_en 26/09/03 16:06 Page 1

2
General
Precautions of use
• Your remote control is fitted with an LCD touch screen requiring specific precautions of use.
• Do not apply heavy pressure on it.A slight pressure with the finger is sufficient.
• Do not use sharp and/or metallic objects.
• Avoid shock and mechanical constraints, high temperatures (35° C maximum), vibration,
humidity.
• Read and follow the indications in this manual to install the batteries and set the various
functions.
• Do not let children use the remote control alone.
• Your ROC 850 remote control is designed for domestic use, and not industrial use. It must be
used within a family and private environment.
• Any dismounting or modification of this remote control cancel your rights to the guarantee.
• Also apply the instructions and guidelines detailed in this user manual.
• In case of any particular problem or question, refer to page 20 before calling your retailer or
our technical support at the following number:
THOMSON shall not be responsible if the ROC 850 is not used according to this manual.
You can contactTHOMSON by dialling: 0871 712 1312
(For Great-Britain, all calls will be charged 0,10£ / mn)
www.thomson-europe.com
ROC850_en 26/09/03 16:06 Page 2

3
About your remote control
EN
EN
Your ROC 850 remote control is a universal remote control designed to be used with most
Audio/Video equipment.Thanks to its 8 mode keys, your ROC 850 replaces up to 8 for the
following devices:
- TV set : TV mode key
- VCR : VCR mode key
- CD player : CD mode key
- DVD player : DVD mode key
- Satellite receiver : SAT mode key
- Cable receiver : CBL mode key
- Amplifier/tuner : AUDIO mode key
- Other audio video device : AUX mode key
Your remote control is fitted with an LCD (Liquid Crystal Display) touch screen.This screen
displays a keypad, with virtual keys you can use when programming or controlling a device. In this
manual, the touch screen keys are designated LCD keys, whereas the other keys (actual keys) are
designated keypad keys.
Your ROC 850 includes many features:
• MACRO function, to memorize 9 keystrokes (up to 20 keys each of the 9 macro keys
available).
• LEARN function, used to download the codes from another remote control (up to 40 keys
per mode).
• Scan/Search function.
• ShowView/VideoPlus+ (SV/V+) key.
• All off function: to switch off all devices.
• TV Volume/Mute control regardless of the last mode selected.
• Key to shift between 2 channels prefered (P<P).
• Customization the LCD touch screen according to your requirements.
Your ROC 850 includes an extended library of infrared codes you can use to control most
current devices (2003). However, some more recent or older devices may not be compatible with
this remote control.
ROC850_en 26/09/03 16:06 Page 3

About your remote control
4
Installing the batteries
Insert the 4 batteries supplied (LR03 / AAA) according to the direction indicated (polarity).
Note: programmed keys maintain programming when replacing the batteries.
About the batteries
• Your ROC 850 uses 4 LR03 (AAA) batteries.When changing the batteries, choose preferably
alkaline batteries, and ensure they are inserted in the right direction (polarity).
• Do not leave the batteries in the remote control if you intend no to use it for a long period
of time. Used batteries can leak an acid liquid.This liquid can damage the remote control and
is toxic: it burns the skin and the mucous. Use gloves when handling such batteries.
• Remove the batteries if you intend not to use your remote control for a long period of time.
• Do not throw the batteries into a fire; store them away from sources of intense heat; do not
short them: they may explode.
• Never let a child play with batteries as he/she may bite them, swallow them, or choke on
them.
• Please respect the environment and prevailing regulations. Before you dispose of
batteries ask your dealer whether they are subject to special recycling and if he accepts
to take them back.
ROC850_en 26/09/03 16:06 Page 4

About your remote control
5
EN
EN
Description of keys and LED
LED: lights up briefly whenever used (pressing a key or the touch screen). Indicates the
transmission of a command. Blinks 3 times in case of mistake.
TV,VCR,CD,SAT,CBL,DVD,AUDIO,AUX: operating mode keys, used to select the
device to control.
B: switch off the device for the mode selected.
VOL +/-: set the volume on certain devices.
M(MACRO): Use a macro command (see page 13).
S(SETUP): Use to program the remote control according to the device to control. It is
also used to access secondary functions (one press on the SETUP key, in the VCR mode,
displays or hides the letter Sin the top right corner of the touch screen).
: mute on/off on certain devices.
PR +/- :selecting the next or previous channel.
a/I: Display or remove Videotext.With some devices, quit theVideotext with the
EXIT key of the touch screen (see page 6).
PLAY,REW,FF,REC,STOP,PAUSE: to control a disc player or VCR.These keys also
match the color FAST TEXT keys for the TV,CBL, and SAT modes.
1
2
3
4
6
7
8
910
11
5
2
1
3
4
11
10
6
5
9
7
8
ROC850_en 26/09/03 16:06 Page 5

About your remote control
6
Description of the touch screen keys
The LCD touch screen is used as a virtual keypad, activated when pressed. It
includes 15 areas representing 15 keys.These keys are contextual, i.e. their
number and function depend on the device to control.Therefore, they
depend on the mode chosen (keypad key on which you have pressed TV,
VCR, …).
Your remote control can display 2 virtual keypads on the LCD touch screen for current use.The
SCREEN key on the touch screen is used to shift between screens.The display disappears after a
few seconds inactivity.To activate the display, press the SETUP key (6) or one of the MODE
keys (2) on the keypad, or any area of the LCD screen.The other keys on the keypad do not
activate the LCD screen.The keys common to all the modes are described below.
Keys 0 to 9 Select a channel number or enter the number of the device to
control.
-/-- Direct selection of channels beyond 9 with most devices. For other
devices, first press the
0 key and enter the name of the channel
required (e.g. for the chain 53, enter
053 ).
AV Select an Audio/Video socket (view the images of a device connected
to the device controlled (DVD player, SAT receiver,VCR,…).
SEARCH Scan channels or sequences (see page 19)
P<P Memorize 2 of your favorite channels, and shift from one to the other
using this key (see page 14).
SCREEN Shift from one touch screen to the second screen for the mode
selected.
Browsing keys for menu selections.
MENU Display the menu of the device controller.
OK Confirm a choice in a menu.
EXIT Remove menu on TV screen.
Displays the channel number, program title...
Main Screen
Secondary Screen
ROC850_en 26/09/03 16:06 Page 6

About your remote control
7
EN
EN
Other very useful touch screen keys
Devices and screens
(Main screen = 1, Secondary screen = 2)
Functions
2
2
2
2
2
2 2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
2
1
2
2
2
2 2
TV VCR SAT CAB CD AUDIO DVD
Displays a videotext page over a
transparent TV image.
Videotext page change stop.
Programs TV sleep (timeout between 1
and 99 minutes, see page 19).
Displays the channel number, program
title...
Select the SP or LP modes on certain
VCRs (simple play or long play function).
To open the disc tray or to eject a
cassette.
Access to the ShowView or VideoPlus+
function on certain VCRs (see page 19).
Display program guide on screen.
Access to favorite channels.
Select loudspeaker A pr B.
Set the volume level.
Select digital signal processing (DSP).
Select sound effects.
Confirm an action.
Repeat a disc or a sequence between 2
points,A and B, with certain players.
Go to chapters beyond 09 on a DVD
disc in certain players.
Read a track or a chapter of a disc.
ROC850_en 26/09/03 16:06 Page 7

8
Programming the ROC 850
Any device (TV,VCR, satellite receiver, …) can be controlled using the VCR,DVD,SAT,CD,
AUDIO,CBL and AUX mode keys, provided the remote control is programmed, by allocating
the 3-digit code matching the make of the device to control, or using 2 other code scanning
methods.Therefore, the remote control can be programmed in several ways: by entering a code,
scanning by make, auto scanning.
Note: when pressing, the red indicator lights briefly, and you hear a beep. An error is indicated by 3 blinkings
and 3 beeps.
Programming by entering a 3-digit code
Note: before starting, take the document appended in your hands. It lists the codes for most devices. Search
for the type (TV,VCR, …) and make of the device you wish to control. For certain makes, several codes are
proposed.These different codes apply to various generations of devices. Program the remote control by
testing each code, until you find the code covering the most functions possible. Certain codes do not enable
controlling the device required, whereas other codes provide access to more or less functions.
1. Switch on the device to control (TV,VCR, …).
2. Activate the touch screen by pressing it.
3. Press and hold the SETUP (6) key until the red indicator remains lit (2-3
seconds) and the following screen displays (Setting screen). Release the
SETUP key.
4. Press the CODE key on the touch screen.The following screen displays (Mode screen).
5. Press a mode key (TV,VCR,SAT...) on the keypad (2) according to the device to control.
The following screen displays (Code screen).
6. Using the list of codes appended, enter the first 3-digit code for the make of the device you
wish to control (the SEARCH key disappears after entering the second digit).The red
indicator switches off after the last digit entered. It confirms the integration of the code (code
correct). In case of error, the indicator blinks fast during a few seconds.The main screen
displays.
7. Press the EXIT key on the touch screen.The virtual screen for controlling the device chosen
in step 4 displays. Programming is complete.
Note: point the remote control towards the device and press the Bkey on the keypad (3). If the device
switches off, this means the code entered is correct. All you need to do is check the various keys on the touch
screen, in order to determine whether the keys proposed on the screen can be used to control the device
concerned. If keys are inoperative, reprogram the remote control using another code proposed in the list.
8. Repeat this procedure for the other devices to control (TV,VCR,DVD,SAT,CD,AUDIO
and AUX).
ROC850_en 26/09/03 16:06 Page 8

Programming the ROC 850
9
EN
EN
Programming using the Brand scan method
To avoid searching by entering a code or too long automatic scan, you can scan according to the
brand of the device to control. Make scanning is available only for the CD and AUDIO (HiFi)
modes.
Note: this method presumes you wish to memorize a VCR code under the VCR mode, a satellite receiver
code under the CBL mode, etc …To memorize, for example, a VCR code under the CBL or other code, the
CBL mode key must be dedicated to the list of VCR codes.You can assign any VCR code under the CBL
mode, by applying the method described in page 8, before scanning.
1. Switch on the device to control (TV,VCR, …).
2. Activate the touch screen by pressing it.
3. Press and hold the SETUP (6) key until the red indicator remains lit (2-3 seconds) and the
following screen displays (Setting screen). Release the SETUP key.
4. Press the CODE key on the touch screen.The following screen displays (MODE screen).
5. Press the mode key (TV,VCR,SAT...) of the device to control on the
keypad (2).The following screen displays (CODE screen).
6. Press one of the numeric keys (0to 6) matching the make of the device to control (refer to
the separate codes list).
Note: when pressing 0you launch a complete scan identical to the code scanning method (see page 10).
7. Press the SEARCH key on the touch screen once.The SEARCH screen displays.
8. Press the key on the touch screen (or the Bor PLAY keys on the keypad).The remote
control sends a series of codes and beeps.When the device switches off or the channel
changes (according to the key pressed in step 8) press the key (7) immediately to
memorize the corresponding code.The main screen displays. Code scanning is completed.
Note: if you have accidentally overshot the code, you can browse back by pressing the key on the touch
screen or the PR- key on the keypad.To move forward, press the key on the touch screen or the PR+
key on the keypad.
9. Repeat this procedure for the other devices to control (TV,VCR,DVD,SAT,AUX).
Note:
• point the remote control towards the device, and press the Bkey on the keypad (3). If the device
switches off, this means the code found by the remote control is correct.You only need to check that the
various keys on the touch screen proposed enable controlling the device concerned. If touch keys are
inoperative, reprogram using make scanning, by restarting the procedure.
• When all the codes for a make have been tested, the red indicator blinks 3 times to indicate scanning is
complete, and the main screen displays.
ROC850_en 26/09/03 16:06 Page 9

Programming the ROC 850
10
Programming using the auto scan method
If you were unable to find the satisfactory code using the manual entry or make scanning
methods, try the auto scan method below.
Note: this method presumes you wish to memorize a VCR code under the VCR mode, a satellite receiver
code under the CBL mode, etc …To memorize, for example, a VCR code under the CBL or other code, the
CBL mode key must be dedicated to the list of VCR codes.You can assign any VCR code under the CBL
mode, by applying the method described in page 8, before scanning.
1. Switch on the device to control (TV,VCR, …).
2. Activate the touch screen by pressing it.
3. Press and hold the SETUP (6) key until the red indicator remains lit (2-3 seconds) and the
following screen displays (Setting screen). Release the SETUP key.
4. Press the CODE key on the touch screen.The following screen displays (MODE screen).
5. Press a mode key (TV,VCR,SAT...) on the keypad (2) according to the device to control.
The next screen appears (CODE screen).
6. Press the SEARCH key on the touch screen once.The SEARCH screen
displays.
7. Press the key on the touch screen (or the Bor PLAY keys in the keypad).The remote
control returns a series of codes and beeps.When the device turns off or changes channel
press the (7) key immediately to memorize the corresponding code.The main screen
redisplays. Code scanning is complete.
Note: point the remote control towards the device and press the Bkey (3) on the keypad. If the device
switches on, this means the code found by the remote control is correct.You only need to check that the
various keys on the touch screen proposed on the screen enable controlling the device concerned. If touch
keys are inoperative, reprogram by make scanning, by restarting the procedure.
8. Repeat this procedure for the other devices to control (TV,VCR,DVD,SAT,AUX).
Note:
• once all the codes matching a make have been tested, the red indicator blinks 3 times to indicate that
scanning is complete, and the main screen displays.
• Code scanning starts from the last code memorized under the mode concerned.Therefore, if auto scan
tests the 100 mode codes concerned, and if the code in memory in the remote control is code 050, code
search will start from code 051 up to code 100, then returns to 000 to 050.
ROC850_en 26/09/03 16:06 Page 10

Programming the ROC 850
11
EN
EN
Identifying codes found during scanning
1. Activate the touch screen by pressing it.
2. Press and hold the SETUP (6) key until the red indicator remains lit (2-3
seconds) and the following screen displays (Setting screen). Release the
SETUP key.
3. Press the CODE key on the touch screen.The following screen displays (MODE screen).
4. Press the MODE key (TV,VCR,SAT...) on the keypad (2) according to the device to
control.The next screen appears (CODE screen).
5. Press the SETUP (6) key.The 3 digits of the code memorized appear
one after the other.The main screen displays. Identification of the code is
completed. Press the EXIT key on the touch screen.
ROC850_en 26/09/03 16:06 Page 11

12
Programming a Macro
You can memorize up to 9 control sequences (Macros) in your remote control. Each sequence
can run a series of 20 instructions. Once memorized, press the MACRO (5) key and the touch
screen key for the sequence to run. Before programming, take a few minutes to write down the
sequence to compose.This will be particularly useful to achieve your programming and use it
later.
Programming without timeout
1. Activate the touch screen by pressing it.
2. Press and hold the SETUP (6) key until the red indicator remains lit (2-3
seconds) and the Setting screen displays. Release the SETUP key.
3. Press the MACRO (5) key on the touch screen.The MACRO screen
displays.
4. Press 1 to 9 to number the sequence.
5. A new screen displays, using the keypad (2), press the key of the mode
desired (TV,VCR,SAT,…).The touch screen displays the keys of the
mode selected, as well as the SETUP and MACRO keys.
6. Compose your sequence:
a) Press the sequence of keys to memorize in the exact order required.
b) Use the SCREEN key on the touch screen to go to the 2nd screen.
c) Use a key for the keypad mode (TV,VCR, …) to control different
devices (start a TV ser, select a channel, switch on a satellite
receiver, ...).
7. Press the MACRO (5) key on the keypad to save the sequence. Saving is
automatic when reaching the 20 keys possible.
8. Press the EXIT key on the touch screen to return to the previous menu.
Note:
• In certain cases, you may have to include a timeout between 2 keys. Refer to next
paragraph.
• Secondary keys accessible via the Skey cannot be included in a Macro.
• You cannot include a Macro inside a Macro.
ROC850_en 26/09/03 16:06 Page 12

Programming a Macro
13
EN
EN
Programming with timeout between 2 keys
Inside a sequence, the time between 2 infrared transmissions is 0.5 seconds.
You may have to increase this time in order to leave, for example, the time for the TV to light on
and display the images of a channel.
1. When composing your sequence (step 6page 12), press the SETUP (6)
key on the keypad (or screen) in order to display the timeout screen.
2. Using the touch screen numeric keys, enter the time required (maximum
9 seconds). Indicating a time is considered as being a key (20 keys max
per sequence).
To apply the default timeout (0.5 second), press the EXIT key on the touch
screen without entering a value.
Note: the commands accessible via the Skey cannot be included to a sequence.To quit the Macro mode
while entering a sequence, press the SETUP key twice.
Using a Macro-command
To use a Macro, press the MACRO (5) key on the keypad, then press the appropriate key on the
touch screen (keys 1 to 9 according to the sequences memorized).
Removing a Macro
1. Activate the touch screen by pressing it.
2. Press and hold the SETUP (6) key until the red indicator is list (2-3
seconds) and that the Setting screen displays. Release the SETUP key.
3. Press and hold the MACRO (5) key on the keypad or touch screen.The
red indicator switches off, and the Delete Macro screen displays.
4. Press the key matching the sequence to remove.The red indicator blinks
to indicate that deletion is effective.
To quit the screen without deleting a sequence, press the EXIT key.
ROC850_en 26/09/03 16:06 Page 13

14
Zapping between 2 channels
Use the P<P key on the touch screen to toggle between 2 favorite channels stored previously.
Programming
1. Activate the touch screen by pressing it.
2. Press and hold the SETUP (6) key until the red indicator is list (2-3 seconds) and that the
Setting screen displays. Release the SETUP key.
3. Press the P<P key on the touch screen.The P<P screen displays.
4. Press the mode key required (TV,VCR,SAT,…) on the keypad.The
touch screen displays the mode keys selected, as well as the SETUP and
P<P keys.
5. Enter the first number of one of your 2 favorite channels (1 to 3 digits).
6. If your channel has less than 3 digits, press the mode key (TV,VCR, …)
after entering the number.
7. Enter the second number of your other favorite channel (between 1 and
3 figures).
8. If your channel has less than 3 digits, press the SETUP (6) key after
entering the digit.
9. If you have entered 3 digits, press the EXIT key on the touch screen.
Note: the key for the mode desired must be pressed before entering the channel
number.The commands accessible via key Scannot be used.
The SCREEN key on the touch screen provides access to the 2nd screen.
A pressure on the SCREEN key of the touch screen is considered as being an
entry.
Use (zap between 2 channels)
1. Activate the touch screen by pressing it.
2. Press the P<P key on the touch screen to zap from one channel to another.
ROC850_en 26/09/03 16:06 Page 14

15
Customizing the touch screen
EN
EN
You can select the keys which will be displayed or hidden when displaying each mode.You can
change any touch key, except the SCREEN,SLEEP,SEARCH and P<P keys.
1. Activate the touch screen by pressing it.
2. Press and hold the SETUP (6) key until the red indicator remains lit (2-3 seconds) and the
display of the next screen (Setting screen). Release the SETUP key.
3. Press the SCREEN key on the touch screen.The next screen displays (MODE screen).
4. Press the key of the mode required (TV,VCR,SAT,…) on the keypad.
5. The touch screen displays the keys for the mode selected, as well as the
SETUP and SCREEN keys.
6. You can now allocate other functions to each of the touch screen keys,
or clear them by pressing as many times as required on the key
concerned.
7. After customizing the touch screen for a mode, you can customize it for
another mode, by pressing the key of the mode required (TV,VCR,
SAT,…).Your settings in the previous mode are saved.
8. To save your customized setting and return to the main screen, press the SETUP key.
9. Press the EXIT key on the touch screen to return to the previous menu.
Note: the SCREEN key on the touch screen provides access to the 2nd screen.
The SLEEP,SETUP,MACRO,LEARN,P<P,KEY? and SEARCH keys cannot be changed.
Returning to the default screen
You can cancel your customized settings and return to the default screen.
1. Activate the touch screen by pressing it.
2. Press and hold the SETUP (6) key until the red indicator remains lit (2-3
seconds) and the display of the next screen (Setting screen). Release the
SETUP key.
3. Press the SCREEN key on the touch screen.The next screen displays
(MODE screen).
4. Press the key of the mode required (TV,VCR,SAT,…) on the keypad.
5. The touch screen displays the keys for the mode selected, as well as the
SETUP and SCREEN keys.
6. Maintain the key of the mode to restore depressed.
7. The main screen displays, press EXIT to quit.
Note: to cancel your screen customization and return to the default screen, press the Mode key and hold it
during about 3 seconds (until the main screen appears).The SLEEP,SETUP,MACRO,LEARN,P<P,
KEY? and SEARCH keys cannot be customized.
ROC850_en 26/09/03 16:06 Page 15

16
Learning a code
To recover all the features of one of your original remote controls (e.g. the one supplied with
your TV set), you can download the infrared codes from the original remote control into your
ROC 850.Your ROC 850 can “copy” up to 40 keys per mode.
Before starting, read the following tips:
• Check that the batteries in both remote controls are not used.
• Perform a zero reset of programming before starting this operation (see page 18).This means
that all the parameters in the ROC 850 remote control will be restored to their default value
(factory settings).
• Lay both remote controls as shown in the figure below, and at same horizontal level as the
ROC 850.
• Leave a distance of about 5 cm between both remote controls, while ensuring you are away
from an incandescent or energy saving lamp.
• Perform a test, by downloading 2 or 3 keys and trying them out.Then perform a zero reset
before a full download of all the functions in the original remote control.
• When downloading a key, do not release the key transmitted as long as the screen does not
redisplay and the red indicator remains lit.This can require 2 to 3 seconds.
• No function can be memorized under the SCREEN,SLEEP,P<P,SEARCH keys of the
touch screen or the SETUP,MACRO,TV,VCR,DVD,CBL,SAT,CD,AUX or AUDIO
keys on the keypad.
3 to 5 cm
ROC 440
3 to 5 cm
ROC850_en 26/09/03 16:06 Page 16

Learning a code
17
EN
EN
Instructions for downloading keys
1. Activate the touch screen by pressing it.
2. Press and hold the SETUP (6) key until the red indicator remains lit (2-3 seconds) and the
display of the next screen (Setting screen). Release the SETUP key.
3. Press the LEARN key on the touch screen.The MODE screen appears.
4. Press the mode key desired (TV,VCR,SAT,etc.) on the keypad.The
LEARN screen displays.This screen includes the touch keys in the mode
selected, as well as the SETUP and LEARN keys.
5. Press the touch key or keypad key for which you wish to download the
first key of the original remote control. Use the SCREEN key on the
touch screen to open the 2nd screen.
6. Press and hold the key on the original remote control until the red
indicator on the ROC 850 blinks once and the LEARN NEXT screen
appears (this can take 2 to 3 seconds). In case of error, the red indicator
blinks during 3 seconds, but the ROC 850 remains in the learning mode
with the LEARN NEXT screen displayed.To download a new key, press
the LEARN key on the touch screen and return to step 5in the above
procedure.To memorize and quit the learning mode, press the OK key
on the touch screen.The Setting screen displays. Learning is complete.
7. Quit by pressing the EXIT key on the touch screen.
To clear all the keys downloaded in a given mode
1. Activate the touch screen by pressing it.
2. Press and hold the SETUP (6) key until the red indicator remains lit (2-3 seconds) and the
display of the next screen (Setting screen). Release the SETUP key.
3. Press and hold the LEARN key on the touch screen.The MODE screen
displays.
4. Press the mode key required (TV,VCR,SAT,etc.) on the keypad.The
LEARN screen displays.
5. Press and hold the SETUP (6) key until the Setting screen displays.All
the keys downloaded under the mode concerned are then cleared.
ROC850_en 26/09/03 16:06 Page 17

18
Other functions
Beep
A beep can be generated when pressing the keys. If you wish to remove this feature, you can
disable it and reactivate it later.
1. Activate the touch screen by pressing it.
2. Press the SETUP (6) key until the red indicator remains lit (2-3
seconds) and the display of the next screen (Setting screen). Release the
SETUP key.
3. Press and hold the STOP key on the keypad for a few seconds until the
red indicator blinks.
Note: to activate the beep, perform the same procedure, but press the PLAY key
instead of the STOP key.
Backlighting
Your ROC 850 is fitted with a photo-sensitive cell which triggers automatic key backlighting when
ambient light is insufficient.You can also trigger lighting by hiding the cell located at the front of
the remote control.You can change the backlighting time, set to 30 seconds by default.
1. Activate the touch screen by pressing it.
2. Press and hold the SETUP (6) key until the red indicator remains lit (2-3
seconds) and the display of the next screen (Setting screen). Release the
SETUP key.
3. Press the SETUP (6) key.A numeric keypad with 9 keys displays.
4. Select a duration by pressing one of the 9 keys (1 for 10 seconds, 2 for
20 seconds, 3 for 30, etc.).
5. Press the ENTER key on the touch screen. Setting is completed.
Zero reset
To reset your ROC 850 and restore factory settings (default settings).
1. Activate the touch screen by pressing it.
2. Press and hold the SETUP (6) key until the red indicator remains lit (2-3
seconds) and the display of the next screen (Setting screen). Release the
SETUP key.
3. Press and hold the SETUP (6) key during about 5 seconds, until the red
indicator switches on and off and the screen disappears. Zero reset is
completed.The remote control is back to the original setting when
purchased.
Scanning the channels
This function is used to view automatically, one after the other, the channels of a TV set or
satellite or cable receiver. Press the SEARCH key once on the touch screen to browse the
channels. Channel change is performed every 3 seconds, to stop, press any key.
Note: after 2 minutes, browsing stops.
ROC850_en 26/09/03 16:06 Page 18