THUNDER TIGER Catherine User manual

No.5300/5301L/5301G/5302
The Majestic
Length: 21" (533mm)
Beam: 7.8"(198mm)
Height: 14.5"(370mm)
Motor : 550 included
King Fisher
Length: 21.65" (550mm)
Beam: 8.1"(205mm)
Height: 18.5"(470mm)
Motor : 550 included
Lobmaster
Length: 21.65" (550mm)
Beam: 8.1"(205mm)
Height: 18.5"(470mm)
Motor : 550 included
Catherine
Length: 23.6"(600mm)
Beam: 8.7"(220mm)
Height: 20.9"(530mm)
Motor: 550 installed
Specifications
Scale Fishing Boat
Assembly Instructions
1

INTRODUCTION
All of us at Thunder Tiger want to thank you for choosing the Scale Fishing Boat. These boats are full
equipped with radio, servos, and forward/backward 50A ESC, 4.5A6V battery and wall charger that will
provide lots of scale boating fun.
Never control your boat without doing frequency and range check.
Do not intend to touch the propeller as it may cause serious injury.
Do not run in the creek, river, stream or any running water.
Safety is always the first issue, make sure the area is safe.
Do not swim or jump into water to get back your boat in case the boat is out of control
or stop by any case in the water.
Always check the inside of the hull and make sure there is no water.
Try to keep it dry after boating, this will keep electric devices last longer.
Do not ever run the boat if there is a big wave. Strongly recommend to run the boat in
still water.
Thunder Tiger guarantees that you should enjoy many hours of trouble free use from our R/C products.
Thunder Tiger products have been sold worldwide through the authorized distributors that are supported
directly and rapidly from Thunder Tiger. You may find that Thunder Tiger is always pursuing to explore
new items creatively with highest quality. To update the latest product information and to get the best
technical support , please feel free to contact your local hobby shops or Thunder Tiger authorized
distributor.
Thoroughly read this assembly instruction manual is strongly recommended. This is to familiarize
yourself with the product and all devices.
Warranty: The Scale Fishing Boat is guaranteed to be free from defects in material and workmanship
at the date of purchase . It does not cover any damage caused by use or modification. The warranty
does not extend beyond the product itself and is limited only to the original cost of the kit. By the act of
assembling or controlling this boat, the user accepts all resulting liability for damage caused by this
product. If the buyer is not prepared to accept this liability, it can be returned new and unused to the
place of purchase for a refund.
Notice: Adult Supervision Required: This is not a toy. Assembly and running of this product requires
adult supervision. Read through this book completely and become familiar with the assembly and
control of this boat. Inspect all parts for completeness and damage. Contact Thunder Tiger authorized
agent if you find any problem or need tech support.
Caution:
2

Open the box and check that you have all the parts as shown below.
If anything is missing please contact your dealer.
CONTENTS
Transmitter x 1
Receiver x1
4.5A 6V Pb-Acid Battery
Wall Charger
Velcro x 2
Radio Instruction Manual
Boat Instruction Manual
Replacement Parts
PJ6042 Drive Shaft( Catherine)
PJ6045 Drive Shaft( Lobmaster, King Fisher)
PJ6046 Drive Shaft( The Majestic)
PJ6044 Propeller
PJ6043 Joiner
PJ6047 550 Motor
No.26254.5A6V Pb-Acid Battery
No.2630 110V 2P Wall Charger
No.2631 230V 2P Wall Charger
No.2632 230V 3P Wall Charger
No.8023 F/B 50A ESC
PJ6040 Fisher Crew PJ6041 Tire Set
3
Optional Part

Step1:Open box and take out the boat carefully. Step2:Remove the tight band and all wraps, place
the boat on wood stand.
Follow the manual step by step. The boat name is indicated in each photo as the manual is written for all
scale fishing boats. There are some steps may vary,you may skip the steps if manual does not mention.
4

Step3:Do not trash the box as there is a small
box which contains master, rigging and
sails. This will be assembled later.
Step4:Locate Transmitter, Receiver, Battery, Wall
Charger and BatteryCord.
Step5:Remove the deck from the hull by loosening
two retainers
Step6:Install Receiver in place as shown.
5

Step7:Plug the rudder servo connector at CH1
and ESC connector at CH2.
Step8:Secure battery with furnished Velcro in the
hull as shown. Connect Battery to ESC with
the Battery Cord.
Note: Red to Red and Black to Black.
Well organize the wires and make sure the all
wires do not contact the drive shaft. .
6

Step9:Refer to furnished radio manual and set up your radio. Always switch transmitter on first,
ESC last. Turn off ESC first and transmitter last. Make sure Throttle and Steering are at neutral
pos ition and in correct direction.
Please see ESC manual at page14.
Step10:Make sure rudder is perpendicular to
the pushrod. Adjust it by threading in or
out of the clevis if necessary.
Step11:Tread the antenna wire through the deck
as shown then secure the deck with the
two retainers.
CH CH
CH CH
21
21
UP
Down
counter clockwise
clockwise
Right
Left
Right Turn
Left Turn
7
Tread the antenna wire through the hatch cover.

Step12:Carefully remove the masts from the box. As all riggings are factory knotted,please be patient to separate
all riggings as shown. Install two masts then hook up all riggings in place as indicated.
8

Make sure two masts are vertical and parallel to each
other. You may twist the rigging (counter clockwise) to
get good tension before you hook up. Route the antenna
along with the mast.
9

10