Thunderbook TITAN A103 Instruction manual

QUIck user’S GUIDE
titan A103

En
3
TABLE OF CONTENTS
Safety Instructions....................................................................................4
Package Contents.....................................................................................6
Device Description....................................................................................7
Inserting SIM y Micro-SD Cards.............................................................10

4
SAFETY INSTRUCTIONS
Batteries:
Batteries are parts whose life cycle depends on handling. If no failure is reported
within 3 months after receipt of the equipment, the battery will be considered to be
functioning properly. Failure to comply with these regulations will lead to the loss of
guarantee.
Please note the following:
• Fully charge the battery every three months.
• Do not work with the device at less than 20% battery as it may damage the battery.
The device will not come under warranty if it is detected that the battery is at 0%
charge.
• The LED indicator on the front of the tablet should blink during charging. If not, it is
due to a battery failure.
• Before working in negative temperatures, make sure the battery is 85% charged or
higher.
• In negative temperatures do not work with the equipment with a load below 60%.
• The battery charge temperature is 0ºC to 40ºC.
• The storage temperature of the battery is between 0ºC and 25ºC. Charge the battery
(or equipment) before storing it.
• Avoid exposing the device or battery to high temperatures.
• Do not overcharge the battery. The full charge is indicated when the indicator LED
stops flashing.
• Do not expose the battery to mechanical stress.
• Do not damage the batteries with sharp or pointed objects.
• Do not throw batteries into re - they may explode.
• Do not throw liquids on the batteries.
• Avoid short-circuiting the batteries, as it can lead to overheating and ignition of the
battery.
• If liquid comes out of the battery and comes into contact with eyes or skin, rinse
immediately with clean water and seek medical attention.
• Incorrect battery replacement may cause a risk of explosion.
• Replace the battery only with the same or equivalent recommended by the
manufacturer.
• Batteries should not be disposed of with normal household waste. Use the service of
specialized stores that perform recycling.
Warning: Please read and observe carefully before using the device!

En
5
Environment:
Protect the device from temperatures outside the specied range. The device is
protected against spray water but must not be submerged in water or be exposed to
water jets. Do not expose the unit to strong magnetic elds or strong static electricity.
Once water or liquid has entered the unit, turn it off and do not use until it is dried.
Have it checked by a qualied specialist.
Safety in operation:
Do not drop the device. Do not bend or twist it. This may result in a breakage of the
display glass or of circuit boards and mechanical parts. To avoid hearing damage,
listen to music via headphones at a moderate volume and never place the speaker
outputs directly in front of your ear. Keep packaging materials and small parts away
from children. There is a danger of suffocation. Never open the case of the appliance
or the charger (risk ofelectric shock, short-circuit and re). Do not put objects through
slots or openings on the appliance or charger (risk of electric shock, short circuit,
and re). Do not attempt to open the unit, the unit may be destroyed and you will lose
warranty.
Cleaning:
Never clean the surface of the appliance with solvents, detergents or other chemical
products. Use a soft, dry cloth instead.
Power supply:
Always use the original charger or one with suitable current and voltage rating to
prevent damage to the device. If you use an universal charger, consider the polarity of
the charger as well as the current and the voltage rating. Do not unplug the charger
from the wall outlet by pulling the cable. Do not use chargers with damaged cables or
plugs.
Disposal:
Dispose used electronic equipment at the appropriate collection points. Please note
that your device has a battery and therefore it must not be disposed with normal
household waste. Please consult your local or municipal authorities for the correct
disposal route of your device and battery.

6
Package Contents
Check your product box for the following items:
- Titan A103
- Hand Strap
- USB type C to female USB cord (15cm)
- USB type C to male USB cord (1m)
- Charger
This device is in compliance with the essential safety
requirementsand other relevant provisions set out in the
European Directive.

En
7
DEVICE DESCRIPTION
1
4 5
6
7
8
9
10
2 3
1. Barcode scanner trigger
2. Power button
3. Volume (+ / -)
4. Barcode scanner (optional)
5. Rear camera
6. Audio
7. Mini HDMI
8. USB type C
9. USB 3.0
10. DC-jack
11. Speaker
12. Hand strap fixation points
12
11

8
Inserting SIM & Micro-SD cards
Opening
Pull to open the rubber cover. Opening is hard to ensure the IP sealing.
Inserting the mini SIM card
The slot accepts only mini SIM cards. Insert the card into the SIM slot
like shown in the picture on the next page.
Inserting a SD card
Insert the micro SD card into SD card slot.
Closing
Close the protective caps after inserting the cards to preserve IP
sealing.
Tip:
For the SIM card, a Pin number may be requested. Enter the SIM card
pin number and tap OK.
Warning:
Before inserting SIM or SD card the device has to be shut down.

En
9
Micro
SIM
Micro
SD

10
Use barcode reader
1. Make sure there is an application open on the device and that a
text eld is focused (with the text cursor in the text eld).
2. Point to a barcode with the back of the device.
3. Press and hold the shutter button (located on the top of the device
with the letter “F”).
4. The data capture LED is lit and a beep sounds by default to
indicate that the barcode has been decoded correctly. Focus the
capture LED on the barcode until the beep sounds.
5. Release the trace button. Barcode content data is displayed in the
text eld.
Attention:
• To activate the reader it is necessary to start the
“application” HardDeCode if the device has been
rebooted, shut down or restored.
• Your device may not have a barcode reader,
depending on the conguration acquired.
• Note that the default conguration of the reader is via
USB HID.
Use of the barcode reader

En
11
Location of the trigger button + barcode reader
Restore to factory settings
Scan the following barcodes to congure the barcode reader if
necessary.
Install barcode reader driver

Av. Corts Catalanes, 5-7
08173 - Sant Cugat del Valles
Barcelona - Spain
https://www.thunderbook.eu