Thunderbook COLOSSUS W803 Instruction manual

Quick user’s guide
COLOSSUS W803

2
TABLE OF CONTENTS
Package Contents....................................................................................3
Safety Instructions....................................................................................4
Device Description....................................................................................8
Replacing the battery...............................................................................10
Inserting SIM & Micro-SD cards.............................................................12
Use of the barcode reader.......................................................................14

En
3
Package Contents
Check your product box for the following items:
- Rugged Tablet Colossus W803
- Hand Strap
- Charger
This device is in compliance with the essential safety
requirements and other relevant provisions set out in the
European Directive.

4
SAFETY INSTRUCTIONS
Batteries:
Batteries are parts whose life cycle depends on handling. If no failure
is reported within 3 months after receipt of the equipment, the battery
will be considered to be functioning properly. Failure to comply with
these regulations will lead to the loss of guarantee.
Please note the following:
• Fully charge the battery every three months.
• Do not work with the device at less than 20% battery as it may
damage the battery. The device will not come under warranty if it is
detected that the battery is at 0% charge.
• The LED indicator on the front of the tablet should blink during
charging. If not, it is due to a battery failure.
• Before working in negative temperatures, make sure the battery is
85% charged or higher.
• In negative temperatures do not work with the equipment with a
load below 60%.
• The battery charge temperature is 0ºC to 40ºC.
• The storage temperature of the battery is between 0ºC and 25ºC.
Charge the battery (or equipment) before storing it.
• Avoid exposing the device or battery to high temperatures.
• Do not overcharge the battery. The full charge is indicated when the
indicator LED stops flashing.
Warning: Please read and observe carefully before using the device!

En
5
• Do not expose the battery to mechanical stress.
• Do not damage the batteries with sharp or pointed objects.
• Do not throw batteries into re - they may explode.
• Do not throw liquids on the batteries.
• Avoid short-circuiting the batteries, as it can lead to overheating
and ignition of the battery.
• If liquid comes out of the battery and comes into contact with
eyes or skin, rinse immediately with clean water and seek medical
attention.
• Incorrect battery replacement may cause a risk of explosion.
• Replace the battery only with the same or equivalent recommended
by the manufacturer.
• Batteries should not be disposed of with normal household waste.
Use the service of specialized stores that perform recycling.

6
Environment:
Protect the device from temperatures outside the specied range. The
device is protected against spray water but must not be submerged
in water or be exposed to water jets. Do not expose the unit to strong
magnetic elds or strong static electricity. Once water or liquid has
entered the unit, turn it off and do not use until it is dried. Have it
checked by a qualied specialist.
Safety in operation:
Do not drop the device. Do not bend or twist it. This may result in a
breakage of the display glass or of circuit boards and mechanical
parts. To avoid hearing damage, listen to music via headphones at
a moderate volume and never place the speaker outputs directly in
front of your ear. Keep packaging materials and small parts away
from children. There is a danger of suffocation. Never open the case
of the appliance or the charger (risk ofelectric shock, short-circuit and
re). Do not put objects through slots or openings on the appliance or
charger (risk of electric shock, short circuit, and re). Do not attempt
to open the unit, the unit may be destroyed and you will lose warranty.
SAFETY INSTRUCTIONS

En
7
Cleaning:
Never clean the surface of the appliance with solvents, detergents or
other chemical products. Use a soft, dry cloth instead.
Power supply:
Always use the original charger or one with suitable current and
voltage rating to prevent damage to the device. If you use an universal
charger, consider the polarity of the charger as well as the current and
the voltage rating. Do not unplug the charger from the wall outlet by
pulling the cable. Do not use chargers with damaged cables or plugs.
Disposal:
Dispose used electronic equipment at the appropriate collection
points. Please note that your device has a battery and therefore it
must not be disposed with normal household waste. Please consult
your local or municipal authorities for the correct disposal route of
your device and battery.

8
DEVICE DESCRIPTION
Frontal camera
Volume (+ / -)
Barcode scan trigger
Power button
Windows button
1
4
2
5
3
2
1
3
4
5

En
9
USB 3.0 Rear camera
USB type C Docking connector
Audio Battery lock
Barcode reader
Mini HDMI User removable battery
611
914
712
10
813
6
14
7
8
9
10
12 13
11

10
Removing the battery
Removing the battery
1. Slide the two latches to unlock the protective battery cover.
2. Take off the protection cover.
3. Slide the battery lock latch up
4. Remove the battery
Warning: Make sure the device is properly shut down before
attempting to remove the battery.
1
3
2 4
1

En
11
INSERTING THE BATTERY
Inserting the battery
1. Insert the battery from the contact side.
2. Slide the battery lock latch down
3. Put the battery cover back in place.
4. Slide the two latches to lock the protective battery cover
4
2
1
3
4

12
Inserting SIM & Micro-SD cards
Warning:
• Before inserting SIM or SD card the device has to be shut down.
• To install or to remove the SIM card or SD card, the battery Has to
be removed rst (page 10).
• The slot tray only detects one SIM and one Micro SD
1. Remove the battery (page 10)
2. Remove the card slot tray.
3. Put the SIM and Micro SD card according to the slots on the tray.
4. Insert the tray from the slots.
5. Install the battery (page 11).

En
13
Micro-SD
SIM

14
Use of the barcode reader
Use barcode reader
1. Make sure there is an application open on the device and that a
text eld is focused (with the text cursor in the text eld).
2. Point to a barcode with the top of the device.
3. Press and hold the shutter button (located on the front of the
device with the letter “F”).
4. The data capture LED is lit and a beep sounds by default to
indicate that the barcode has been decoded correctly. Focus the
capture LED on the barcode until the beep sounds.
5. Release the trace button. Barcode content data is displayed in the
text eld.
Attention:
• Your device may not have a barcode reader, depending on the
conguration acquired.
• Note that the default conguration of the reader is via USB HID.
Barcode reader location

En
15
Location of the barcode reader trigger button
To congure your BCR with line break, you will need to scan the
following codes from rst to last in the correct order:
Enter setup Enable sufx
Set the Sufx on Return
(Validation) Exit setup
1 2
3 4

Av. Corts Catalanes, 5-7
08173 - Sant Cugat del Valles
Barcelona - Spain
https://www.thunderbook.eu