Thunderbook Colossus A100 Instruction manual

Quick user’s guide
COLOSSUS A100

2
TABLE OF CONTENTS
Package Contents.....................................................................................3
Safety Instructions....................................................................................4
Device Description.....................................................................................8
Replacing the battery...............................................................................10
Inserting SIM y Micro-SD Cards.............................................................12
Use of the barcode reader.......................................................................14

En
3
Package Contents
Check your product box for the following items:
- Rugged Tablet Colossus A100
- Hand Strap
- Carrying Case Handle
- Micro-USB to female USB cord (15cm)
- Micro-USB to male USB cord (1m)
- DC-Jack Charger
- USB Charger
- Carrying Bag
This device is in compliance with the essential safety
requirements and other relevant provisions set out in the
European Directive.

4
SAFETY INSTRUCTIONS
Batteries:
Batteries are parts whose life cycle depends on handling. If no failure
is reported within 3 months after receipt of the equipment, the battery
will be considered to be functioning properly. Failure to comply with
these regulations will lead to the loss of guarantee.
Please note the following:
• Fully charge the battery every three months.
• Do not work with the device at less than 20% battery as it may
damage the battery. The device will not come under warranty if it is
detected that the battery is at 0% charge.
• The LED indicator on the front of the tablet should blink during
charging. If not, it is due to a battery failure.
• Before working in negative temperatures, make sure the battery is
85% charged or higher.
• In negative temperatures do not work with the equipment with a
load below 60%.
• The battery charge temperature is 0ºC to 40ºC.
• The storage temperature of the battery is between 0ºC and 25ºC.
Charge the battery (or equipment) before storing it.
• Avoid exposing the device or battery to high temperatures.
• Do not overcharge the battery. The full charge is indicated when the
indicator LED stops flashing.
Warning: Please read and observe carefully before using the device!

En
5
• Do not expose the battery to mechanical stress.
• Do not damage the batteries with sharp or pointed objects.
• Do not throw batteries into re - they may explode.
• Do not throw liquids on the batteries.
• Avoid short-circuiting the batteries, as it can lead to overheating
and ignition of the battery.
• If liquid comes out of the battery and comes into contact with
eyes or skin, rinse immediately with clean water and seek medical
attention.
• Incorrect battery replacement may cause a risk of explosion.
• Replace the battery only with the same or equivalent recommended
by the manufacturer.
• Batteries should not be disposed of with normal household waste.
Use the service of specialized stores that perform recycling.

6
Environment:
Protect the device from temperatures outside the specied range. The
device is protected against spray water but must not be submerged
in water or be exposed to water jets. Do not expose the unit to strong
magnetic elds or strong static electricity. Once water or liquid has
entered the unit, turn it off and do not use until it is dried. Have it
checked by a qualied specialist.
Safety in operation:
Do not drop the device. Do not bend or twist it. This may result in a
breakage of the display glass or of circuit boards and mechanical
parts. To avoid hearing damage, listen to music via headphones at
a moderate volume and never place the speaker outputs directly in
front of your ear. Keep packaging materials and small parts away
from children. There is a danger of suffocation. Never open the case
of the appliance or the charger (risk ofelectric shock, short-circuit and
re). Do not put objects through slots or openings on the appliance or
charger (risk of electric shock, short circuit, and re). Do not attempt
to open the unit, the unit may be destroyed and you will lose warranty.
SAFETY INSTRUCTIONS

En
7
Cleaning:
Never clean the surface of the appliance with solvents, detergents or
other chemical products. Use a soft, dry cloth instead.
Power supply:
Always use the original charger or one with suitable current and
voltage rating to prevent damage to the device. If you use an universal
charger, consider the polarity of the charger as well as the current and
the voltage rating. Do not unplug the charger from the wall outlet by
pulling the cable. Do not use chargers with damaged cables or plugs.
Disposal:
Dispose used electronic equipment at the appropriate collection
points. Please note that your device has a battery and therefore it
must not be disposed with normal household waste. Please consult
your local or municipal authorities for the correct disposal route of
your device and battery.

8
DEVICE DESCRIPTION
123
1
2
3
Webcam
Ambient light sensor
Touchscreen

En
9
5
4
6
7
8
9
16
15
10 11 12 13
14
17
18
14
21
19 20
22
4Kensington Lock
5Audio-in
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Mini-HDMI
Micro-USB
USB Type A
DC-in
Volume - / +
Programmable Button
Power Button
Barcode Scanner Trigger
Accessories Attachement
POGO-Pin
RJ-45 (Ethernet)
RS-232 (COM)
Camera
Barcode Scanner (Optional)
Hand Strap Fixation Points
22 Battery Release Lock

10
Removing the battery
Removing the battery
1. Press and slide the Release Lock Button to unlock the battery.
2. Slide the battery, as shown in the picture.
3. Lift the battery up by its back end.
4. Pull out the battery.
12
Warning: Make sure the device is properly shut down before
attempting to remove the battery.

En
11
INSERTING THE BATTERY
Inserting the battery
1. Insert the battery with the non-contact side rst.
2. Push down the other side of the battery and slide the battery like
shown in the picture.
3. Press the Release Lock Button and slide it to the “Locked”
position.
Image 9.2
1
2

12
Inserting SIM & Micro-SD cards
Tip:
For the SIM card, a Pin number may be requested. Enter the SIM card
pin number and tap OK.
Warning:
• Before inserting SIM or SD card the device has to be shut down.
• To install or to remove the SIM card or SD card, the battery Has to
be removed rst (page 6).
Inserting the mini SIM card
The slot accepts only mini SIM cards. Insert the card into the SIM slot
like shown in the picture on the next page.
Inserting a SD card
Insert the micro SD card like show in the picture on the next page.
Closing
Please refer to “Inserting the battery” (page 9).

En
13
up
down

14
Use of the barcode reader
Use barcode reader
1. Make sure there is an application open on the device and that a
text eld is focused (with the text cursor in the text eld).
2. Point to a barcode with the back of the device.
3. Press and hold the shutter button (located on the top of the device
with the letter “F”).
4. The data capture LED is lit and a beep sounds by default to
indicate that the barcode has been decoded correctly. Focus the
capture LED on the barcode until the beep sounds.
5. Release the trace button. Barcode content data is displayed in the
text eld.
Attention:
• To activate the reader it is necessary to start the
“application” HardDeCode if the device has been
rebooted, shut down or restored.
• Your device may not have a barcode reader,
depending on the conguration acquired.
• Note that the default conguration of the reader is via
USB HID.

En
15
Barcode reader location
Location of the barcode reader trigger button

Av. Corts Catalanes, 5-7
08173 - Sant Cugat del Valles
Barcelona - Spain
https://www.thunderbook.eu