TIE DOWN 71069 User manual

404-344-0000 • www.tiedown.com
605 Stonehill Drive SW, Atlanta, GA 30336
[email protected]
Instruction Sheet #08378
E1837, Rev. 5/25/21
Keep these instructions for future reference.
Read and understand these instructions
before using this product.
WARNING: This product can expose you
to chemicals including Nickel, which is
known to the State of California to
cause cancer. For more information
go to: www.P65Warnings.ca.gov
WARNING: This product can expose you
to chemicals including Nickel, which is
known to the State of California to
cause cancer. For more information
go to: www.P65Warnings.ca.gov
WARNING: This product can expose you to
chemicals including Nickel, which is known to
the State of California to cause cancer. For more
information go to: www.P65Warnings.ca.gov
WARNING: This product can expose you to chemicals including Nickel, which is known to the
State of California to cause cancer. For more information go to: www.P65Warnings.ca.gov
WARNING: This product can expose you to chemicals including Nickel, which is known to the
State of California to cause cancer. For more information go to: www.P65Warnings.ca.gov
Roof
Surface
Parapet Ladder
Safety-Dock
Extension
Ladder
Parapet
Wall
2-Piece Commercial Ladder Safety-Dock Part ID: 71069
3-Piece Parapet Ladder Safety-Dock Part ID: 71070
Parapet Ladder
Safety-Dock
Instruction Manual
Box 1
2-Piece Commercial
Ladder Safety-Dock
Box 2
3-Piece Parapet Ladder
Safety-Dock.
The Parapet Ladder Safety-Dock is OSHA Compliant and can
be installed on both parapet and flat roofs. If installing on flat
roofs, see installation for Commercial Ladder Safety-Dock.
Scan QR code for flat roof installation.
Tools Required
Drill
14” drill bit for metal or masonry
Socket bits
Wrench set
Reciprocating saw and metal blade
2 - Piece Commercial Ladder Safety-Dock
Part ID: 71069 - Box Contents:
Parapet Ladder Safety-Dock with chains
“L” bracket and 2 carriage bolts, washers & nuts
Safety-Handles and mounting hardware
3 - 17” threaded rods with 6 nuts & washers and
3 fender washers, Brace and fasteners
3 - Piece Parapet Ladder
Part ID-71070 - Box 1 & 2 Contents:
Parapet Ladder Safety-Dock with chains
“L” bracket and 2 carriage bolts
Safety-Handles and mounting hardware
3 - 17” threaded rods with 6 nuts & washers
and 3 fender washers, Brace and fasteners
Parapet Safety-Ladder and 4 mounting bolts & nuts
2 Ladder feet and 2 self-tapping screws
NOTE:
The 2-Piece Ladder Safety-Dock is designed for a 6” to
13” wide parapet. By flipping the “L” Bracket, it can work
on up to a 15” wide parapet. However, the 3-Piece Lad-
der Safety-Dock (with ladder) only works on parapets 6”
to 13” wide. Please call office for additional information.

TIE DOWN Safety Products Division
800-241-1806 • 404-344-0000 • www.tiedown.com
E1837, Rev. 5/25/21
2
Parapet Ladder Safety Dock
Drill Here
Slip Sheet
“L” Bracket
“L” Bracket
Secure “L” bracket
with washers, and
nylock nuts on inside
of the parapet wall
Secure threaded bolt
with fender washers,
washers, and nylock
nuts on the outside
of the parapet wall
Drill Here
Slip Sheet
“L” Bracket
“L” Bracket
Secure “L” bracket
with washers, and
nylock nuts on inside
of the parapet wall
Secure threaded bolt
with fender washers,
washers, and nylock
nuts on the outside
of the parapet wall
Drill Here
Slip Sheet
“L” Bracket
“L” Bracket
Secure “L” bracket
with washers, and
nylock nuts on inside
of the parapet wall
Secure threaded bolt
with fender washers,
washers, and nylock
nuts on the outside
of the parapet wall
Drill Here
Slip Sheet
“L” Bracket
“L” Bracket
Secure “L” bracket
with washers, and
nylock nuts on inside
of the parapet wall
Secure threaded bolt
with fender washers,
washers, and nylock
nuts on the outside
of the parapet wall
Step 1
Install slip sheet on top of parapet.
Step 3
To fasten Ladder Safety-Dock to parapet,
drill 2 holes thru parapet at location shown in
Step 2. Insert 17” threaded rods thru parapet.
Fasten with fender washers, washers, and
nylock nuts on outside of parapet and washers
and Nylock Nuts on inside of parapet.
IMPORTANT: Cut excess bolts length off to
the nut to eliminate snag points. Coat end of
bolt with sealant or rust inhibiting paint.
Step 2
Attach “L” Bracket to the dock using two 3/8”x 1” carriage bolts,
washer, and nylock nut. Orient “L” Bracket as shown to left.
NOTE:
The 2-Piece Ladder Safety-Dock is designed for a 6” to 13”
wide parapet. By flipping the “L” Bracket, it can work on up to
a 15” wide parapet. However, the 3-Piece Ladder Safety-Dock
(with ladder) only works on parapets 6” to 13” wide.
Please call 877-723-3766 for additional information.

TIE DOWN Safety Products Division
800-241-1806 • 404-344-0000 • www.tiedown.com E1837, Rev. 5/25/21
3
Parapet Ladder Safety Dock
Drill Here
Drill Here
Drill Here
Slip Sheet
“L” Bracket
“L” Bracket
Secure “L” bracket
with washers, and
nylock nuts on inside
of the parapet wall
Secure threaded bolt
with fender washers,
washers, and nylock
nuts on the outside
of the parapet wall
Step 6
Fasten bottom of brace with fender washers,
washers, and nylock nuts on outside of parapet and
washers and nylock nuts on inside of parapet
IMPORTANT: Cut excess bolts length off to the
nut to eliminate snag points. Coat end of bolt
with sealant or rust inhibiting paint.
Step 5
Adjust the Brace against the parapet wall.
Mark wall and drill thru parapet.
Step 4
Install Brace. Fasten top of Brace to the Dock
using a 3/8” x 1” carriage bolt, bolt head down
and nut up.
Self tapping
screws
Step 7
Install Handles. Slide handles between
Safety-Dock and parapet as shown left. From the
top of the Safety-Dock, fasten handles using two
3/8” x 1” hex head screws each handle. From the
side of the Safety-Dock, fasten handles using two
3/8” x 2-1/2” carriage bolts, washers and nylock
nuts each handle.

Parapet Ladder Safety Dock
Self tapping
screws
Self tapping
screws
Step 8
Cut Ladder to size. Place ladder on roof and rest against Ladder-Dock.
Measure excess ladder from top mounting hole in ladder to top
mounting hole on Handle. Cut excess ladder length from the bottom of
Ladder. Slide adjustable feet onto bottom of ladder.
Step 9
Attach Safety-Ladder to the Safety-Dock
with (4) 3/8”x 4” carriage bolts and 3/8”
washers and nylock nuts.
Step 10
Extend the ladder feet down making sure they are
touching roof surface, fasten to the ladder using
1/4”x 3/4” self-tapping screws.
Ladder
Adjustable Foot
Safety Products Division
605 Stonehill Drive SW, Atlanta, Georgia 30336
404-344-0000 • www.tiedown.com
ISO 9001:2015 Certification
Intellectual Property of TIE DOWN Inc. ©2021 TIE DOWN, Inc.
Instruction #08378 (E1837 Rev. 5/25/21)
4