INNOVAPLAS FIESTA 1001-N-C-S User manual

Sand
20 lbs
FIESTA 1001-N-C-S / OPERA 1016-N-C-S WITH CLASSIC 6003
Tools Required (not included)
Contents of Fiesta # 1001-N-C-S or Opera # 1016-N-C-S
x2
x2
x4
x8
105-012
105-005
x8 x8
115-010
1) Insert the four
posts into the step
receptacles post
ends and secure
them in place with
the bolts, washers and
nuts provided.
2) Insert the platform, 2
small handrails, and 2
large handrails over the
2 rear posts.
Do not secure yet.
Security strap
SCREW BAG 140-058
A weather resistant padlock is
recommended.
PG. 1
REV. 29/03/11
Fiesta - Classic 6003 shown.
Instructions also compatible for Opera - Classic 6003
x2
x2
x2
x2
x1
x2
x2
105-012
105-005
x2 x2
115-014 (3/4 in.)
x14
Contents of the ladder box SKU # 6003
(not included)
Sand
125-035
WARNING
Do not dive or jump from step or ladder.
Use BATTERY operated tools to avoid electric shocks.
Install step on flat surface, following the manufacturers instructions.
Remove step from pool during freezing climate season.
Manufacturer cannot be held responsible for injuries caused by abusive
use of product.
Ask your city about specific regulations that apply to your above-ground
pool and ladder.
Maximum functional
width is 1/4 inch.
A
115-018 (2 1/2 in.)
x2
x4
LOCK
5/16 inch
drill bit
370 Lajeunesse St,
St-Jérome (Québec),
Canada J7Y4E5
x2
x8
105-012
105-005
x8 x8
115-010
115-015 (1 1/2 in.)
x8
x12
115-014 (3/4 in.)
115-018 (2 1/2 in.)
x2
HARDWARE BAG 140-008

REV. 29/03/11
B
x8
115-014 (3/4 IN.)
PG. 2
Insert the Step CupTM
in the 4 holes under
the step.
x4
3) Twist the Step CupTM to
ensure that its mushroom
has entirely cleared the
wall thickness.If it has,
the suction cup should
rotate freely.
Failing to install the Step cup™ will greatly reduce the steadiness
of the step and will void the manufacturer warranty.
2) With a flat screwdriver,
compress the
Step CupTM
mushroom ring while pushing
it into the hole.
CAUTION
1) Insert half of the Step CupTM
mushroom in the hole, at a 45
degree angle.
Sand
20 lbs
370 Lajeunesse St,
St-Jérome (Québec),
Canada J7Y4E5
C
1) Install the four
post covers.
2) Secure the
handrails to the
posts using the
screws provided.
Do not secure
platform.
D
1) Insert the sandbag
under the first step.
2) Slowly submerge
the step in the pool.
Make sure you do not
damage the liner in
the process.
*All
Step CupTM
must be installed
*MINIMUM OF 1"
CAUTION*
To prevent a pool liner puncture, install all
Step Cup ™ as specified and keep a minimum
of 1" inch gap between the pool liner and
the rear underside of the step.

REV. 29/03/11
x2
105-012
105-005
x2 x2
125-035
115-014 (3/4 in.)
x12
Security strap
x2
1) Once the step is in the pool
secure the platform to the top
seat (see illustration) using the
two straps provided.
115-018 (2 1/2 in.)
x2
OPTIONAL:
Once the pool step has been completely assembled and secured to the
pool, attach the 2 screws supplied through the platform to the top seat of
your pool to provided a more rigid assembly.
SWING THE LADDER UP AND LOCK IN
PLACE WHEN THE POOL IS NOT IN USE
TO PREVENT DROWNING AND
UNAUTHORIZED ENTRY.
WARNING
4) Secure the ladder base to the
post with the screws provided.
x6
115-014 (3/4 IN.)
48'' & 52''
54''
align
EF
MANUFACTURER
WARRANTY
1 year on the ladder
and step.
1 year on the hardware. PG. 3
WWW.INNOVAPLAS.COM
1) Trace a line on each post at 39 inches from the ground for 48'' &
52'' pools. If you have a 54'' pool, trace a line at 40.5'' from the ground.
2) Slide the pivot blocks onto the posts and line up with
the traced marks. Secure with the screws provided.
3) Slide the 2 posts through
the platform and handrails and
slide the lock in place .
370 Lajeunesse St,
St-Jérome (Québec),
Canada J7Y4E5
H
1) Secure the handrails and
platform to the posts with the
screws provided.
2) Secure the ladder to the
pivot blocks using the bolts,
washers and nuts provided.
GUse sliding lock as a guide to drill
hole into ladder in up position.
Use a 5/16'' drill bit.
**PADLOCK REQUIRED**
lock