Tiger River Caspian User manual

Tiger River Spa Pre-Delivery Instructions
2005 Pre-Delivery Instructions
Please take the time to read this booklet carefully, as it will provide you with the information you will need to ensure
the safe, secure, and timely installation of your new spa. The following sections are guidelines on how to prepare for
delivery and set-up of your new spa. Specifically covered are site selection, delivery access, ground preparation,
and electrical requirements.
Remember to carefully read the Owner’s Manual that accompanies your spa, and to complete the warranty card
within 10 days of delivery. These items, along with other valuable information, will be found in the Owner’s Package
which has been placed in the equipment compartment of your spa, where you will also find its serial number.
Watkins Manufacturing Corporation reserves the right to change features, specifications and design without
notification and without incurring any obligation.
DATE PURCHASED: __________________________________________________________________________
DATE INSTALLED:______________________________________________________________________________
DEALER: ______________________________________________________________________________________
ADDRESS: ____________________________________________________________________________________
TELEPHONE:__________________________________________________________________________________
In most cities and counties, permits will be required for the installation of electrical circuits or the construction of
exterior surfaces (decks and gazebos). In addition, some communities have adopted residential barrier codes which
may require fencing and/or self-closing gates on the property to prevent unsupervised access to a pool (or spa) by
children under 5 years of age. Your Tiger River spa is equipped with a locking cover that meets the ASTM F1346-91
Standard for Safety Covers and as a result, is usually exempt from most barrier requirements. As a general practice,
your local Building Department will inform you of any applicable barrier requirements at the time a permit is
obtained for the installation of an electrical circuit. Your Tiger River dealer can provide information on which permits
may be required.
Congratulations on your decision to
enjoy the finest spa available...
Welcome to the growing family of
Tiger River®spa owners.

Site Selection and Preparation
IMPORTANT: Site selection and preparation are your responsibility. Carefully read these instructions and consult
your authorized Tiger River®dealer if you have any questions.
You probably have a spot picked out for your new spa, whether it’s indoors or outdoors, on a patio or on a deck.
Just make sure you check the following:
• Always put your spa on a structurally sound, level surface. A filled spa can weigh a great deal. Make
certain that the location you choose can support the weight of your filled spa.
• Don’t forget to level your spa before filling it. (See Spa Leveling Instructions included in Owner’s Manual.)
• Locate your equipment compartment, which houses all of the electrical components, in a place where
water will drain away from it. Allowing water into the equipment compartment can damage the
electronics, or may result in tripping your house’s circuit breaker.
• Leave yourself easy access to the circuit breakers in the subpanel (230 volt models), or to the interrupter
switch on the end of the power cord (115 volt models).
• Never let water get into the subpanel (230 volt models), into the interrupter switch (115 volt models), or
into the electrical outlet that your spa is plugged into. Your 115 volt Tiger River spa will come with a
protective box designed to keep out rain and water from sprinkler systems. Your 230 volt spa’s subpanel
is raintight when installed correctly with the door closed.
• Leave access to the equipment compartment for periodic spa care and maintenance.
OUTDOOR AND PATIO INSTALLATION
No matter where you install your new spa, it’s important that you have a solid foundation to support it. Structural
damage to the spa resulting from incorrect installation or placement on an inadequate foundation is not covered
under the spa’s limited warranty.
If you install the spa outdoors, a reinforced concrete pad at least four inches thick is recommended for the
Caspian™, Bengal®and Sumatran®spas. The reinforcing rod or mesh in the pad should be attached to a bond
wire (see your Owner’s Manual). All Tiger River spas may be installed onto a deck, provided that the load
capacity of the deck is greater than the dead weight of the spa (see Deck Installation).
If you place the spa on the ground, even temporarily, place stepping stones under the leveling areas (see Spa
Leveling Instructions in your Owner’s Manual). The stones should be at least two inches thick and twelve inches
square. Even with stones in place, the spa will inevitably settle and become unlevel. Plus, a spa surrounded by
dirt or grass will soon be filled with dirt or grass from users’ feet; therefore, it is important to get it onto a solid
foundation as soon as possible.
NOTE: The Caspian spa has a drainage hole directly below each speaker between the bottom of the wood siding
and the black base of the spa. Should water get into the speaker area it will drain through these holes.
DECK INSTALLATION
To be certain your deck can support your spa, you must know the deck’s maximum load capacity. Consult a
qualified building contractor or structural engineer before you place the spa on an elevated deck or
indoors. To find the weight of your spa, its contents and occupants, refer to the Spa Specification chart on page
12. This weight per square foot must not exceed the structure’s rated capacity, or serious structural damage could result.
INDOOR INSTALLATION
Be aware of some special requirements if you place your spa indoors. Water will accumulate around the spa, so
flooring materials must provide a good grip when wet. Proper drainage is essential to prevent a build-up of water
around the spa. When building a new room for the spa, it is recommended that a floor drain be installed. The
humidity will naturally increase with the spa installed. Water may get into woodwork and produce dryrot, mildew,
or other problems. Check for airborne moisture’s effects on exposed wood, paper, etc. in the room. To minimize
these effects, it is best to provide plenty of ventilation to the spa area. An architect can help to determine if more
ventilation must be installed.
Your Tiger River dealer can help you with local information such as zoning regulations and building codes.
Pre-Delivery Instructions Page 2

Page 3 Pre-Delivery Instructions
DELIVERY ACCESS
First, locate the dimensions of your spa on the following
chart. The dimensions shown are the measurements of the
spa in the vertical position, laid on its side.
Next, contact your dealer to find the height and width added
by the delivery cart which the dealer will use to deliver your
new spa. Use the height of the cart plus the dimension
shown as H to determine the vertical clearance required to
pass the spa and cart. Use the width of the cart, or
dimension W, whichever is greater, to determine the
maximum width of clearance necessary.
NOTE: It may be necessary to allow for additional over-head
clearance if the spa will be rolled up or down an incline or
moved up or down a short flight of stairs.
Use the information on previous page to determine the
requirements for access to your desired location.
How is your width clearance?
Protruding electric meters
A/C units
Do you have sufficient
overhead clearance?
Check low roof eaves,
overhanging branches,
rain gutters
Is the path clear?
Move away branches, dog
houses, firewood, etc.
If there is a 90 turn, can we
clear it? (The spa will not bend)
No more than 6 consecutive
stairs without a landing
Gas meters
Check all gates
HOUSE
BACK YARD
STREET
Model Width W Length L Height H
Caspian™(CHP) 36” 7’ 0” 7’ 0”
Bengal®(M & MM) 33” 7’ 2 1/2” 6’ 7”
Sumatran®(N) 33” 6’ 6” 6’ 6”

Pre-Delivery Instructions Page 4
It may be necessary to remove a gate, part of a fence, or other movable obstructions in order to roll the spa to its
installation site. About ten percent of the time, a crane is the only way to install the spa by lifting it to its final destination.
If the spa has to be taken off of the cart to go over a wall (either because the entry area is too narrow, the eaves are
too low, the corner is too tight, or the stairway is too steep), a crane will be required. Don’t be alarmed!
The crane has a truck-mounted boom which can fit right in your driveway. It is run by a licensed and insured
operator. For a charge, the crane operator will lift your spa over walls, buildings, or any other obstruction and place
it as close to the installation site as possible. The Tiger River®spa delivery personnel will supervise the crane
delivery and complete the spa installation. Crane delivery typically takes an average of 30 minutes to complete.
NOTE: If your spa delivery requires the use of a crane, you may be required to pay for its services at the completion
of the delivery.
GROUND PREPARATION
Your Tiger River spa has been engineered to perform on all kinds of common yard surfaces. While a concrete slab
is best for long-term use*, other foundations are acceptable so long
as a level base is prepared prior to delivery. Three foundation base
pictures, shown at right, represent examples of alternatives to a
concrete slab for spas installed without gazebos or other
accessories.
*NOTE: A reinforced concrete pad at least four inches thick or a
deck that is able to withstand more than 115lbs. per square foot is
recommended for the Caspian™, Bengal®and Sumatran®spas.
INSTALLATION NOTES:
• If stepping stones or railroad ties are selected for the spa
foundation, they should be placed at the designated leveling
areas of your spa to maintain even distribution of the spa
weight.
• It is important to note that soft surfaces, even when stepping
stones are used to distribute the weight of the spa as evenly
as possible, will still have a tendency to settle unevenly,
resulting in an unlevel spa.
• Remember, placing the spa on grass or dirt may increase the
amount of debris which is inadvertently brought into the spa
water on the user’s feet.
If you are purchasing a deck package or a gazebo with your spa, a
solid foundation becomes mandatory. Placing them on any surface
other than a single level pad could create problems with their
installation. Pictured at right are a few of the recommended surfaces.
As a homeowner, it is your responsibility to provide a suitable, level
foundation for your spa. Keep in mind that most delivery crews are
not equipped to level and prepare spa sites.
If you are interested in having a concrete slab, brick surface, or wood
deck installed, your Tiger River dealer should be able to suggest a
qualified, licensed contractor.
NOTE: In order for the spa to operate properly and the internal
plumbing to drain completely, you must ensure that the spa is
leveled after it has been installed. The diagrams on the following
pages indicate the recommended shimming points on your spa’s
base support system. Your Tiger River spa delivery crew can help
you perform the procedure.
ELECTRICAL
RAILROAD TIES
PRE-CAST
STEPPING STONES
PEA GRAVEL
OR CRUSHED ROCK
FOUNDATIONS FOR SPAS ONLY
(No accessories such as cover or gazebo)
CONCRETE PADS
BRICK SURFACES
WOOD DECKING
FOUNDATIONS FOR SPAS
WITH ACCESSORIES

x Page 5 x
59" (149.9 cm)
80" (203.2 cm)
18" (46 cm) 18" (46 cm)
49 1/2" (125.7 cm)
3 1/2" (8.9 cm)
27 1/2" (69.8 cm)
32 1/2" 82.6 cm)
36" (91.4 cm)
MAIN DRAIN
1 3/4" (3.8 cm) ELECTRICAL CUTOUT
(location may vary 1/2" (1.3 cm) )
UPSIDE DOWN VIEW OF SPA
DOOR SIDE
84" (213.4 cm)
21 1/2" (54.6 cm)
18 1/2" (47 cm) 21 1/2" (54.6 cm) 17 1/2" (44.5 cm)
84" (213.4 cm)
CENTER MIDDLE SHIMS
12 1/2" (31.8 cm)
21" (53.3 cm)
SECONDARY DRAIN
65 1/2" (166.4 cm)
Page 5 Pre-Delivery Instructions
Caspian
™
(Model CHP)
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
(Bottom view)
(Front view)
• 15 Leveling Points (place shims approx. 18” in from edge, then center middle shims)

x Page 6 xPre-Delivery Instructions Page 6
61" (154.9 cm)
54 1/2" (138.4 cm)27 3/4" (70.5 cm)
18" (46 cm) 18" (46 cm)
22" (55.9 cm)
36" (91.4 cm)
3 1/2" (8.9 cm)
27" (68.6 cm)
29 1/2" (74.9 cm)
33" (83.8 cm)
MAIN DRAIN
1 3/4" (3.8 cm) ELECTRICAL CUTOUT
(location may vary 1/2" (1.3 cm) )
UPSIDE DOWN VIEW OF SPA
55 1/4" (140.3 cm) 27" (68.6 cm)
DOOR SIDE
79" (2.01 m)
17 1/4" (43.8 cm) 17 1/2" (44.5 cm)
19 3/4" (50.2 cm) 20 1/4" (51.4 cm)
86 1/2" (2.2 m)
CENTER MIDDLE SHIMS
13 1/2" (34.3 cm)
68" (173.0 cm)
SECONDARY DRAIN
Bengal
®
(Model M & MM)
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
(Front view)
(Bottom view)
• 15 Leveling Points (place shims approx. 18” in from edge, then center middle shims)

x Page 7 xPage 7 Pre-Delivery Instructions
61" (155 cm)
57" (144.8 cm)
29 1/4" (74.3 cm) 44 1/2" (113 cm)
15" (28 cm) 15" (28 cm)
43 1/2" (110.5 cm)
17 1/2" (44.5 cm)
3 1/2" (8.9 cm)
27" (68.6 cm)
29 1/2" (74.9 cm)
33" (83.8 cm)
MAIN DRAIN
1 3/4" (3.8 cm) ELECTRICAL CUTOUT
(location may vary 1/2" (1.3 cm) )
UPSIDE DOWN VIEW OF SPA
48" (121.9 cm) 25 3/4" (65.4 cm)
DOOR SIDE
78" (1.98 m)
17 1/2" (44.5 cm)
19 1/4" (48.9 cm) 18 1/2" (47 cm) 18 1/2" (47 cm)
78" (1.98 m)
CENTER MIDDLE SHIMS
15" (38 cm)
SECONDARY DRAIN
Sumatran
®
(Model N)
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
(Front view)
(Bottom view)
• 15 Leveling Points (place shims approx. 15” in from edge, then center middle shims)

x Page 8 xPre-Delivery Instructions Page 8
REQUIREMENTS
To ensure you will have an opportunity to use your spa soon after delivery, it is very important that the required
electrical service has been installed. Unless otherwise stipulated by your dealer, THIS IS YOUR RESPONSIBILITY.
IMPORTANT: All electrical circuits must be installed by a qualified, licensed electrician.
Tiger River®spas are manufactured in two different electrical versions. The Caspian™ and Bengal®(MM) models are
available with a 230 volt continuous heating system. This spa cannot be converted to 115 volt operation.
The Bengal (M) and Sumatran®models are available as 115/230 volt convertible heating systems. These models
come standard from the factory with 115 volt heating systems; however, with the addition of a subpanel and a
control box wiring change, they can be converted to 230 volt operation. See the following sections for the electrical
requirements for 115 volt operation, 230 volt operation and 230 volt converted operation.
115 VOLT OPERATION REQUIREMENTS
The 115 volt spa requires a dedicated 20 amp, 115 volt circuit. This circuit must be properly wired; that is, it must
have a 20 amp GFCI breaker in the main electrical service panel, and #12 AWG wire (including ground wire) and the
correct polarity throughout the circuit.
WIRE SPECIFICATION NOTE: Long electrical runs may require a larger gauge feed wire than stated. We
recommend that a maximum voltage drop of 3% be used when calculating the larger wire size.
NOTE: The term “dedicated” means that only the spa operates on the circuit.
Each 115 volt model comes equipped with approximately 15 feet of usable power cord. (This is the maximum
length allowed by Underwriters Laboratory.) When the spa is installed, the power cord will come out of the bottom
of the equipment compartment.
In addition to the dedicated 20 amp, 115 volt GFCI
protected circuit, your spa requires a 20 amp single
receptacle. This receptacle, which contains an
outdoor-rated, weather-resistant receptacle cover
plate, will be provided to you. The single receptacle
and cover plate should be installed by your
electrician prior to the delivery of your spa.
For your safety, when your electrician is installing
the electrical outlet, it should be no closer than five
(5) feet and no further than ten (10) feet from the
spa. (Reference National Electric Code 680-6a(1)
and 680-41a.)
WARNINGS: Do not connect your spa to an
extension cord!
The 115 volt GFCI switch and the receptacle must
be protected from weather and landscape
sprinklers–they should never get wet.
NOTE: If you require the services of a licensed
electrician, your Tiger River dealer should be able to
suggest one for you.
Your Tiger River spa has been carefully engineered
to provide maximum safety against electric shock.
Remember, connecting the spa to an improperly
wired circuit will negate many of its safety features.

x Page 9 xPage 9 Pre-Delivery Instructions
230 VOLT OPERATION REQUIREMENTS
The Caspian™ and Bengal® (MM) and converted Bengal (M) and Sumatran®models require a 50 amp, single phase,
230 volt circuit breaker in the main electrical service panel.
All 230 volt Tiger River®spas must be wired in accordance with applicable local and national electrical codes, all
electrical work must be done by a licensed electrician.
NOTE: Watkins Manufacturing Corporation REQUIRES THE USE OF A SUBPANEL TO SUPPLY POWER AND
PROTECT THE SPA. On the Caspian and Bengal (MM) models, the subpanel containing GFCI breakers is included
with the spa. On the converted 230 volt Bengal (M) and Sumatran models, the subpanel containing GFCI breakers
must be purchased separately and can be purchased from your Tiger River dealer.
A licensed electrician should install a four-wire electrical service (two line voltages, one neutral, one ground) from the
main electrical service panel to the sub-panel, and from the sub-panel to the spa per the appropriate wiring diagram
as illustrated below.
The grounding conductor must be the same gauge as the line conductor, but at least #10 AWG. Your electrician
should mount the subpanel in the vicinity of the spa but it should not be closer than five (5) feet from the spa water
edge (NEC 680-6c).
INSTALLATION NOTE: After the spa has been installed by the dealer’s delivery crew, your electrician can connect
the conduit from the subpanel to the spa’s IQ 2020®Spa Control Box and then complete the wiring connections in
the control box.
IMPORTANT NOTE: Three different wiring diagrams are shown: one for the Caspian‚ one for the Bengal (MM) and
one for the Bengal (M) and Sumatran models. Always follow the wiring diagram for your specific model.
NOTE: Complete step-by-step Installation and Wiring Instructions for all 230 volt Tiger River models are included in
the Owner’s Manual and with each sub-panel, which can be obtained from your dealer.
WARNING: Removing or bypassing the GFCI breakers in the subpanel at any time will result in an unsafe spa and
will void the warranty.
WIRE SPECIFICATION NOTE: Long electrical runs may require a larger gauge feed wire than stated. We
recommend that a maximum voltage drop of 3% be used when calculating the larger wire size.
Refer to the Wiring Diagrams below for the electrical requirements of the 230 volt models.

x Page 10 xPre-Delivery Instructions Page 10
BENGAL (MM) 230 VOLT PERMANENTLY CONNECTED MODEL
WARNING! The exact physical location of the terminals on the GFCI
breaker will vary between manufacturers. Connecting the hot wire to
the neutral terminal will cause irreversible damage to the control box.
L1 #10 AWG BLUE
54321
L2 #10 AWG RED
N #10 AWG WHITE
L2 #12 AWG RED
L2
L1
L1 #12 AWG BLUE
GRD
GROUND #10 AWG GREEN
GRD
#8 AWG WHITE,NEUTRAL
#10 AWG GREEN,GROUND
#8 AWG BLUE, L1
#8 AWG RED, L2
N
20A
50A
230V, 50 Amp,
2–POLE,
CIRCUIT BREAKER
(NON GFCI)
30A
LESS THAN 100 FT.
MAIN SERVICE
ELECTRICAL
PAN EL
CONTROL BOX
TB1
HEATER
GROUND
*PROVIDED WITH SPA. NOTE: ALL WIRING SHOULD BE COPPER.
CASPIAN 230 VOLT PERMANENTLY CONNECTED MODEL
NOTE: The wire connections to GFCI breakers are for reference only. Always ensure
the white neutral wire is connected to the load neutral of the 30 amp breaker.
L1 #10 AWG BLUE
54321
L2 #10 AWG RED
N #12 AWG WHITE
L2 #12 AWG RED
L2
L1
L1 #12 AWG BLUE
GRD
GROUND #10 AWG GREEN
GRD
#8 AWG WHITE,NEUTRAL
#10 AWG GREEN,GROUND
#8 AWG BLUE, L1
#8 AWG RED, L2
N
20A
50A
230V, 50 Amp,
2–POLE,
CIRCUIT BREAKER
(NON GFCI)
30A
LESS THAN 100 FT.
MAIN SERVICE
ELECTRICAL
PAN EL
CONTROL BOX
TB1
HEATER
GROUND
*PROVIDED WITH SPA. NOTE: ALL WIRING SHOULD BE COPPER.
NOTE: The wire connections to GFCI breakers are for reference only. Always ensure the white
neutral wire is connected to the load neutral of the 20 amp breaker.
WARNING! The exact physical location of the terminals on the GFCI
breaker will vary between manufacturers. Connecting the hot wire to the
neutral terminal will cause irreversible damage to the control box.

Page 11 Pre-Delivery Instructions
BENGAL (M) AND SUMATRAN 230 VOLT CONVERTED MODELS
WARNING! The exact physical location of the terminals on the GFCI
breaker will vary between manufacturers. Connecting the hot wire to
the neutral terminal will cause irreversible damage to the control box.
L1 #10 AWG BLUE
54321
L2 #10 AWG RED
N #12 AWG WHITE
L2
L1
L1 #12 AWG BLUE
GRD
GROUND #10 AWG GREEN
GRD
#8 AWG WHITE,NEUTRAL
#10 AWG GREEN,GROUND
#8 AWG BLUE, L1
#8 AWG RED, L2
N
20A
50A
230V, 50 Amp,
2–POLE,
CIRCUIT BREAKER
(NON GFCI)
30A
LESS THAN 100 FT.
MAIN SERVICE
ELECTRICAL
PAN EL
CONTROL BOX
TB1
HEATER
GROUND
*AVAILABLE FROM DEALER. NOTE: ALL WIRING SHOULD BE COPPER.
NOTE: The wire connections to GFCI breakers are for reference only. Always ensure
the white neutral wire is connected to the load neutral of the 20 amp breaker.
See owner’s
manual or
control box
schematic for
electrical
conversion and
connection
details.

x Page 12 xPre-Delivery Instructions Page 12
Bengal®
(Model M)
1,500
(115 volt)
6,000
(230 volt)
Sumatran®
(Model N)
6'6"
x
6'6"
1.98m
x
1.98m
33"
.84m
65
Square
feet
1,500
(115 volt)
6,000
(230 volt)
310
Gallons
1173
Litres
613
Lbs.
278
Kg.
3,793
Lbs.
1,720
Kg.
105
Lbs. per
square
foot
115v System: 115 volt,
20 amp dedicated circuit
230v System: 230 volt,
50 amp single phase
GFCI protected circuit
115v System: 115 volt,
20 amp dedicated circuit
230v System: 230 volt,
50 amp single phase
GFCI protected circuit
33"
.84m
65
Square
feet
330
Gallons
1,249
Litres
689
Lbs.
312
Kg.
4,204
Lbs.
1,907
Kg.
105
Lbs. per
square
foot
Footprint
dimensions
Height
Effective
filter area
Heater
(Watts)
Water
capacity
Dry weight
Filled weight*
Dead weight*
Electrical
Requirements
Caspian™
(Model CHP)
7'0"
x
7'0"
2.13m
x
2.13m
115V System:
Not available
230V System: 230 Volt,
50 Amp single phase
GFCI protected circuit
36"
.91m
65
Square
feet
4,000
(230 volt)
330
Gallons
1,249
Litres
789
Lbs.
358
Kg.
4,479
Lbs.
2,032
Kg.
110
Lbs. per
square
foot
Bengal®
(Model MM)
33"
.84m
65
Square
feet
330
Gallons
1,249
Litres
689
Lbs.
312
Kg.
4,204
Lbs.
1,907
Kg.
105
Lbs. per
square
foot
7' 2 1/2"
x
6'7"
2.2m
x
2.01m
7' 2 1/2"
x
6'7"
2.2m
x
2.01m
6,000
(230 volt)
115V System:
Not available
230V System: 230 Volt,
50 Amp single phase
GFCI protected circuit
Spa Specifications
CAUTION: Watkins Manufacturing suggests a structural engineer or contractor be consulted before the
spa is placed on an elevated deck.
* NOTE: The “Filled weight” and “Dead weight” of the spa includes the weight of the occupants
(assuming an average occupant weight of 175 lbs).
CONTRACTOR SUGGESTIONS
Electrician
Name: ______________________________________________________________________________________
Telephone: ______________________________________________________________________________________
Name: ______________________________________________________________________________________
Telephone: ______________________________________________________________________________________
Masonry
Name: ______________________________________________________________________________________
Telephone: ______________________________________________________________________________________
Name: ______________________________________________________________________________________
Telephone: ______________________________________________________________________________________

x Page 13 xPage 13 Pre-Delivery Instructions
ADDITIONAL PRODUCTS AVAILABLE FROM YOUR
TIGER RIVER
®
SPA DEALER
General
Name: ______________________________________________________________________________________
Telephone: ______________________________________________________________________________________
Name: ______________________________________________________________________________________
Telephone: ______________________________________________________________________________________
• EverFresh®water care system
• FreshWater®III high output ozone purification system
• Hot Spring®MPS chlorine-free oxidizer
• MPS test strips
• FreshWater™Stain and Scale Defense
• FreshWater Spa Shine
• FreshWater Instant Filter Cleaner
• FreshWater Filter Cleaner
• FreshWater Ph-Alkalinity Down
• FreshWater Ph-Alkalinity Up
• FreshWater Defoamer
• FreshWater Concentrated Chlorinating Granules
• FreshWater Calcium Hardness Increaser
• FreshWater 4-way test strips
• Hot Spring Cover Shield™
• Retractable cover system with clearance requirements
• Cover Cradle®- 24” Clearance required
• Cover Cradle II - 24” Clearance required
• UpRite®- 7” Clearance required
• GlideRite®- 14” Clearance required
• Lift ’n Glide™- 7” Clearance required
• Vinyl covers
• Spa vacuums
• Spa steps
• Stain kits
• Spa upgrade jet kits
• Replacement filter cartridges
• Pillows

SERVICES AVAILABLE FROM YOUR
TIGER RIVER SPA DEALER
Service Cost
Pre-Delivery site inspection ______________
Deliver spa to installation site ______________
Unwrap spa and haul away packaging material ______________
Set up & level spa ______________
Fill the spa with water ______________
Connect the spa to its power source (115 volt models) ______________
Explain and test the spa’s operation
• Jet system
• Comfort Control®system
• Set temperature control
• Control panel functions
Explain the safety features
• GFCI
• Heater high limit
• Heater thermal cut-off
General spa operation & maintenance orientation ______________
Water quality and maintenance orientation ______________
Adjust the water’s Total Alkalinity, Calcium Hardness and pH ______________
Sanitize the water ______________
Inspect the spa cover, place on spa ______________
Review winterizing instructions ______________
Review Owner’s Manual & Warranty Card ______________
Follow-up call ______________
In-store spa water analysis ______________
TOTAL COST ______________
x Page 14 xPre-Delivery Instructions Page 14

x Page 15 xPage 15 Pre-Delivery Instructions
NOTES

x Page 16 x
WATKINS MANUFACTURING CORPORATION
1280 Park Center Drive
Vista, California 92081
[phone] extension 8432
© 2005 Watkins Manufacturing Corporation. Tiger River, Caspian, Bengal, Sumatran, IQ 2020, Cover Shield, EverFresh,
FreshWater and The Home Relaxation Specialists are trademarks of Watkins Manufacturing Corporation.
Part #62261 Rev. A (1/05)