Tiger Tool 20150 User manual

1.800.661.4 661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Have What It Takes
•
Stay Alert! Watch what you are doing and use common sense when
operating this tool.
•
Inspect product for damage prior to using; do not use if product is
in unsafe condition.
•Do not operate tool while under the influence of drugs, alcohol
or medication.
•
Always use safety equipment to prevent injuries. Approved face and
eye protection must always be worn by the operator, as well as others
in the work area.
•
Do not overreach Keep proper footing and balance at all times.
•
Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving parts.
•
Keep hands clear of all pressurized hydraulic components.
•
Always ensure hoses are free from sharp bends and kinks.
• Keep your work area clean and well lit.
CAUTION 10102: FAILURE TO CHECK THE SPHERICAL THRUST WASHER AND REPLACE AS NECESSARY MAY RESULT IN UNREPAIRABLE DAMAGE
TO YOUR UJOINT PULLER GLOVE CASTING. PREVENTATIVE MAINTENANCE AS OUTLINED WILL ENSURE MANY YEARS OF USE FROM YOUR TIGER
TOOL PULLER. FAILURE TO PERFORM PREVENTATIVE MAINTENANCE WILL VOID YOUR WARRANTY.
CAUTION 10217: BEFORE ASSEMBLING BEARING CUPS ON ANY “SPICER LIFE SERIES” DRIVELINE, CLEAN OUTSIDE MACHINED SURFACES OF
YOKE TO BARE METAL—DO NOT GRIND!
Safety Warning
Read all instructions and safety warnings prior to operation. Failure to do so could result in
equipment damage, personal injury or even death.
Heavy Duty U-Joint
Service Kit
20150

The leg design allows you to push on the driveline
or on the U-Joint cross. Works
either way on virtually all Class 7 & 8 U-Joints
Operating Instructions
U-Joint Puller: 10102
CAUTION: Failure to check the spherical thrust washer and replace
as necessary may result in unrepairable damage to your U-Joint
Puller glove casting. Preventative maintenance as outlined below
will ensure many years of use from your Tiger Tool puller. Failure to
perform preventative maintenance will void your warranty.
1Remove all fasteners from bearing cups.
2Slip the U-Joint Puller over the yoke of the driveline.
3Turn the tool’s forcing screw clockwise with either an air or
hand wrench. (Note: reverse thread)
4Once bearing cup has been removed, repeat the process on the
remaining bearing cups.
The 10102 U-Joint Puller may be used with up to a
1" impact wrench without voiding warranty.
Preventative Maintenance
Keep forcing screw clean and lubricated at all times. Failure to
maintain the spherical thrust washer, located inside the glove
will result in excessive wear to the part. Check and lubricate this
part (lubricate load bearing surface in glove, under cap, on both
sides of spherical washer) periodically and replace as necessary.
Contact your Dealer or Tiger Tool for replacement washers.
(We recommend SAE 30 lube for the threads and EP ‘with molly
grease’).
Bearing Cup Installer: 10201
1 Ensure all parts to be assembled are clean
and/or greased where applicable.
2Double check all the needle bearings are present and placed
correctly.
3Start pressing bearing cup into the yoke by hand, making sure
U-joint cross and bearing cup bolt holes line up.
4
Place installer onto the bearing cup, threading bolts
into yoke.
5 Using an impact or hand wrench, turn the forcing screw
until cup is flush to yoke.
6Remove the tool, and install bearing cup bolts.
1.800.661.4 661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Have What It Takes
Heavy Duty U-Joint
Service Kit
20150

Operating Instructions
Bearing Cup Installer: 10217
1If necessary, select the SPL 170 or SPL 140 reducer for your
application and insert into bottom of the SPL 250 Adapter.
2Position u-joint cross and bearing cup onto the yoke. Ensure
grease fitting is in the correct position.
3Reverse the Forcing Screw so the tool can be positioned over
the yoke/bearing cup.
4By hand, tighten the Forcing Screw until the bottom of the
frame of the tool is contacting the yoke making sure the
adapter is centered over the bearing cup.
5By ratchet or impact wrench, apply force to the forcing
screw to press the bearing cup into the yoke. Make sure the
u-joint cross keeps the needle bearings of the bearing cup
in place.
6Once the adapter/reducer is pressed flush against the yoke,
reverse the forcing screw to remove the tool.
7Rotate driveline 180 degrees.
8By hand, insert the opposing bearing cup into the yoke.
9Repeat steps 3 to 6 on remaining bearing cups.
Here at Tiger Tool, your satisfaction is our number one priority.
Should you have any questions about this or
any of our products, please call us at 1.800.661.4661.
Have What It Takes
Heavy Duty U-Joint
Service Kit
20150
1.800.661.4 661
View demonstration videos and a
complete product list at tigertool.com
Technical Support

Item No.
1
2
3
4
5
6
7
8
9
Part Number
10217-9
10217-1
90150-14
10218-3
10218-13
10100-5
10217-2
10218-12
10217-7
Qty.
1
1
1
1
1
1
1
2
1
Description
Forcing Screw
Fork
O-Ring
Installer Anvil
SPL 250 Adpater
FHMS 3/8" - 16 x 3/4"
170 Series Reducer
O-Ring
140 Series Reducer
Parts Breakdown
Bearing Cup Installer
Have What It Takes
1.800.661.4 661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
10217
1
2
3
4
5
8
89
7
6

Item No.
1
2
3
4
5
6
Part Number
10102-1
10102-2
10102-3
10102-4
10102-5
10102-6
Qty.
1
1
1
1
1
1
Description
Fork
Glove
Forcing Screw
Retaining Bolt
Washer
Dome Plug
Parts Breakdown
1.800.661.4 661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Heavy Duty U-Joint Puller
Maintenance Pack for 10102
10102
10101
Have What It Takes
1
2
3
Also available separately.
Contains each of the following items:
2X
1X
1X 6
4
5

Item No.
1
2
3
Part Number
10201-1
10201-2
10201-3
Qty.
1
2
1
Description
Plate
Bolt
Forcing Screw
Parts Breakdown
1.800.661.4 661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Have What It Takes
1
3
2
Bolt-Retained Bearing
Cup Installer
10201