TigerTough 403053 User manual

Tiger Tower ASSEMBLY
INSTRUCTIONS
Helpful Hints and Care
• Verify you have all parts before beginning assembly. If you are missing any parts,
please contact FurHaven Customer Service at 888-459-2337. Do not return to retailer.
• Periodically inspect joints of product and maintain as needed.
• Moisture, humidity or wet conditions may damage product resulting in a shorter use life.
• Prolonged exposure to sun or heat may damage product resulting in a shorter use life.
• This product is recyclable. Please recycle when your pet is done using this toy.
Chimney
Roof
Top Frame Lock
Chimney Base
Frame Side A
Platform Side
Base Scratcher
Tower Base
Platform End
Platform
Frame Side B
Tower Frame
A B
1| Tower Frame
2 pcs
4| Platform Side
4 pcs
5| Base Scratcher
1 pc
2| Frame Side A&B
1 pc each
3| Roof
1 pc
6| Platform End
8 pcs
7| Top Frame Lock
2 pcs
9| Chimney Base
1 pc
10| Chimney
1 pc
8| Platform
4 pcs
11| Tower Base
1 pc
Model: 403053

Tiger Tower ASSEMBLY
INSTRUCTIONS
1 2 3
4 5 6
7 8 9
10 11
Insert the Chimney Base (9) into the top horizontal slot
(nearest to the triangle “roof frame” section of the form) of
a Tower Frame (1).
Insert the four Platforms (8) into the remaining horizontal
slots of the Tower Frame (1) with the scratcher facing up.
Carefully attach the other Tower Frame (1) to the other
ends of the Chimney Base (9) and Platforms (8).
(Caution: The frame may be unstable during assembly.
Take care not to bend or apply weight onto the frame
during this step.)
Carefully push the Platform Ends (6) through the Platform
(8) slots (on the outside of the Tower Frame(1)) to lock the
Platforms in place.
Repeat for both sides and all ends (total of eight Platfom
Ends installed - four on each Tower Frame).
Attach Frame Side A (2) to
the Tower Frame (1) with
the highest platform.
Carefully insert into the
vertical slots and ensure
that Frame Side aligns with
the Platforms. See image.
Insert one Platform Side
(4) into each vertical slot
with Frame Side A (2) to
reinforce the cardboard
barrier and lock the pieces
into place.
Repeat Steps 4 & 5 on
the other side of the
Tower Frame (1) using
the shorter Frame Side B
(2) to align with the lower
platform set. Remember
to lock into place using
Platform Side (4) for
each Platform level.
Fold the Tower Base (11) to
create the triangle ridge in
the center using the prefold
scoring lines. Align the ridge
with the slots in the base of
the Tower Frames (1). Place the Tower on top of the base.
Carefully fold over the edges of the Tower Base (11) into
the vertical slots located at the bottom of the Tower.
Carefully unfold the Chimney
(10) to and fold the top panel
(with hole) down at to cover
the top opening.
Align the tabs in the base of
the Chimney (10) with the tab
slots on the Chimney Base
(9) at the top of the Tower
Frame (from Step 1) and
insert to attach.
Insert the Top Frame Locks
(7) into the Tower Frame (1)
top vertical slots.
Carefully unfold Roof (3).
Position Roof (3) over Tower and align
cutout with Chimney (10).
Keeping roof cutout tabs folded under,
slide Roof (3) over Chimney (9) and set
on Tower Frame (1).
Fold under gable ends of roof to nish
edge.
Insert Base Scratcher (5) panel
into base of Tower.
Sprinkle with catnip and watch
your cat enjoy!
FurHaven Pet Products • Bellingham, WA • [email protected] • 888-459-2337
Chimney
Base (9)
Platform (8)
Frame
Side B (2)
Platform Ends (6)
Platform
Side (4)
Tower Base (11)
Chimney
(10)
Top Frame
Lock (7)
Roof (3)
Base Scratcher (5)