Prevue Pet Products Silverado User manual

L1
L3
L4
L2
A
B
L2
LEFT SIDE
FRONT BACK
RIGHT SIDE
GRILLE
TRAY
SEED GUARD
U3
L3
U4
L4
A
C
B
U1
L1
U2
L2
T1 T2T2
{22} hex head screws
{ 8 } short hex head
screw & nut pairs for
seed guard
touch-up paint
& brush included
{ 1 } allen wrench
{ 4 } rolling casters
{ 3 } cup hangers
{ 3 } stainless steel cups
{ 1 } wood dowel perch
SG1
SG1
SG2SG2
KEY:
T = top
U = upper
L = lower
SG = seed guard
cageassem lyinstructions
Silverad Macaw Cage
M del: # 3155S
cage: 46"L × 36"W × 78¼"H
w/seed guard: 54¾"L × 44¾"W
interi r: 45½"L × 35½"W × 63"H
wire: [gauge] 9 & 9 [spacing] 1⅜"
getting started!
READ THESE NOTES FIRST:
• Enlist A Friend: This is a large cage and requires two
people to assemble.
• Count Hardware: If any screws are missing, please
contact Prevue Customer Service.
• Review All Parts: If parts are bent during shipping,
pieces may be straightened with needle nose pliers. For seriously
damaged pieces, please contact Prevue Customer Service.
•Tools: An allen wrench is included. You may use your own
hand tool with an allen wrench bit. We DO NOT recommend
power drills! Parts can be over-tightened and damaged/stripped.
Prevue is not responsible for this type of damage.
Review these instructions thoroughly before attempting to
assemble cage. If you still require assistance, please contact
Prevue Customer Service at 800.243.3624 or through links
online at prevuepet.com
parts
steps
1Attach casters to legs of lower front (L1)
and lower back (L2) panels.
2a THIS STAGE REQUIRES TWO PEOPLE.
Attach left side lower (L3) panel to
front lower (L1) panel.
→Channels on (L3) face oward in erior of cage.
Install bottom and middle screw only.
Leave top screw out until STEPS 4a & b.
2 Attach rig t side lower (L4) panel to
front lower (L1) panel.
Attach back lower (L2) panel to sides,
continuing to attach with only bottom and
middle screws.
3After lower cage has been assembled,
slide in the grille (A) and drawer (B).

T1
T2
T2
C
SG1 SG2
U2
U3
U4
U1
Made in China for Prevue Pet Products, Inc., Chicago IL USA revue et.com 800 243-3624 customerservice@revue et.com3155S — 07/13 — US
4a THIS STAGE REQUIRES TWO PEOPLE.
Back upper (U2) panel fits into back
bottom (L2). hen post is aligned with
hole, secure panel with screw.
→Have firs person hold (U2) panel uprigh —
so as no o bend pos s—while second person
secures panel.
4 Front upper (U1) panel fits into front bottom
(L1). hen holes are aligned, secure panel
with screws.
→Again, have firs person hold upper panel uprigh .
4c Side upper (U3 – with one cup door; U4 –
with two cup doors) panels are interchangeable.
→Make sure cup doors swing ou (no in o cage).
Slide side upper panel into channels on
back upper (U2) and front upper (U1) panels.
→May require wo people.
Three vertical wires on (U3) and (U4) panels
extend below lower horizontal wire. Align wires
with corresponding holes along top rail of side
lower panel [ (L3) or (L4) ].
5ith lower and upper portions of the cage
assembled, this is an easy time to add cup
olders/stainless steel cups to the side
panel cup doors, and to install the wooden
dowel perc .
6a THIS STAGE REQUIRES TWO PEOPLE.
Center top (T1) roof panel fits into channels
at the very top of front upper (U1) and
back upper (U2) panels. Attach with
screws at the four bottom corners.
6 Side top (T2) roof panels are interchangeable.
Three hooks along top bar of (T2) roof panels
link into handles along lower bar of the (T1) panel.
Three vertical wires on (U3) and (U4) panels extend
above the upper horizontal wire. Align wires with
corresponding holes along bottom rail of (T2) panel.
Attach (T2) panels with screws in lower corners.
7Add front door (C). Female sleeves on
the door slide down over male posts.
8THIS STAGE REQUIRES TWO PEOPLE.
Front and back seed guard (SG1) panels have
three metal “L” tabs along lower bottom edge.
Hook tabs into sleeves along lower rail on front
lower and back lower (L1 & L2) panels.
→Use he shor hex screw & nu pairs.
hile first person holds side seed guard (SG2)
panel in place, second person aligns holes in
corners, and secures front and side panels with
screw & nut pairs.
✩Your cage is now fully assembled!