Tinker & Rasor PD Instruction sheet

Tel: [phone]
2828 FM 758 New Braunfels, TX 78130
Web: www.tinker-rasor.com E-mail: [e-mail]
- 1 -
Sponsoring members of NACE International, NACE Foundation QMF-570 104-154
PRODUCT INSTRUCTIONS
MODEL PD
PEARSON DETECTOR
FIVE SECTIONS of QUICK INFORMATION
I. Model PD Functions
II. Operation Methods
III. Apparatus
IV. Instructions for Unpacking & Inspection
V. Operating Instructions
TINKER & RASOR MODEL PD PEARSON DETECTOR
I. Model PD Functions
A. Pearson Type Holiday Detector
The Tinker & Rasor Pearson type detector was designed to locate discontinuities, flaws or breaks in the
coating of buried pipelines. This method makes possible the exact location of coating breaks in buried lines without
access to the surface of the coated pipe. Locating electrical discontinuities aids in evaluating the application of a
coating and also these discontinuities can be repaired to eliminate corrosion and to reduce the amount of current
required for cathodic protection.
B. Short Locator
The apparatus is also effective in locating shorts or undesirable electrical contacts to buried coated pipe.
Such electrical contacts should be removed prior to placing a pipeline under cathodic protection, as these contacts
would drain a large amount of protective potential from the coated pipe.
C. Pipe Locator
The apparatus can be used very effectively as a pipe locator on coated pipelines that are electrically
connected by a screw or welded joints. This application is particularly effective where it is desired to locate and
follow one pipeline along a right-of-way where there are a number of buried lines.
II. Operating Methods
A. Pearson Survey Method
The method used to locate discontinuities is that of applying audio frequency AC energy between the coated
pipe and ground. A traverse along the pipeline is made in which the difference in potential is indicated across
approximately twenty to thirty feet of soil above the line. This potential difference is noted in the Receiver. When

Tel: [phone]
2828 FM 758 New Braunfels, TX 78130
Web: www.tinker-rasor.com E-mail: [e-mail]
- 2 -
Sponsoring members of NACE International, NACE Foundation QMF-570 104-154
PRODUCT INSTRUCTIONS
an area is reached where the difference in potential is considerably greater than the average potential over the
pipe, a discontinuity is assumed to lie under this area.
B. Method of Locating Shorts
The method of locating shorts or contacts on a coated pipe is that of applying a relatively large amount (5
to15 watts) of audio frequency AC between the pipe and a remote ground connection. A traverse is made along
the pipeline with a Receiver equipped with a search coil. A short or contact is observed along the traverse where
the average AC signal picked up over the line suddenly drops to a very low level. This is assumed to be a point
directly above the contact.
C. Method of Locating Pipe
An audio frequency AC signal is placed between the coated pipe and a good ground connection. The
Receiver, containing a search coil, is passed over the area where the pipe is assumed to be located. As the
Receiver is moved back and forth in a horizontal plane over the pipe, a sharp null will occur in the received signal.
The pipe to be located is assumed to be directly under this null. A well-coated pipeline can be followed for a very
great distance by this method when audio power of from five to fifteen watts is applied to the coated pipe.
III. Apparatus
The complete apparatus furnished with the Pearson-type detector comprises the following:
A. Solid state Oscillator
B. Solid state Receiver with filter
C. Lightweight headphones w/plug and cushions
D. Shoe cleats
E. Connecting cables
F. Carrying Case
A. Oscillator
The Oscillator provided with the set has been designed to use the latest developments in this type of
instrumentation. A signal of 750 C.P.S. is generated by using a power transistor switching circuit. This arrangement
eliminates troublesome vibrators, buzzers or other moving part elements. The Oscillator converts low voltage (12
volts) DC to stable audio-frequency AC directly; hence, by a highly efficient method, the input current to the
Oscillator is only 1.7 amperes for a full output of 15 watts, a conversion efficiency of better than 80%.
In order that a maximum of energy can be transferred from the Oscillator to the pipe, the output of the Oscillator
is provided with taps so that voltages of 2.5, 5, 7.5, 15, 50 and 100 volts are available to match the load. An
interrupter is provided to make the signal more easily recognized. The Interrupter is actuated by a switch on the
panel of the Oscillator. The Oscillator will produce 15 watts of 750 Cycle signal into a 500-ohm load with the output
selector set at the 100 volt position.
NOTE: Model PD-C (Rev. B) uses a new crystal that produces an interrupt frequency at a faster rate than
previous models. Users familiar with this instrument may notice the difference.
B. Receiver

Tel: [phone]
2828 FM 758 New Braunfels, TX 78130
Web: www.tinker-rasor.com E-mail: [e-mail]
- 3 -
Sponsoring members of NACE International, NACE Foundation QMF-570 104-154
PRODUCT INSTRUCTIONS
The Receiver employs a high gain amplifier and a sharply tuned 750 Cycle filter. Modern circuit design insures
maximum circuit stability even when operated at ambient temperature extremes. The filter attenuates AC power
line and other interference, permitting operation in the vicinity of high-tension lines. A loudspeaker is built into the
Receiver, eliminating the need for earphones except in noisy areas.
Plugging the earphones into the jack marked PHONES disables the loudspeaker. A search coil is contained
within the receiver and is normally connected to the Receiver input. Plugging the cable from the cleat terminal
board into the jack marked CLEATS automatically disconnects the search coil and connects the cleats to the
amplifier. The meter gives a visual indication of signal intensity and also serves to check battery condition. To test
the battery, turn the Receiver on and push the button marked BATTERY TEST. Replace battery if necessary.
C. Shoe Cleats
The shoe cleats provided with the detector have been designed for maximum foot comfort and for the most
effective ground contact.
D. Connecting Cables
All necessary connecting cables are furnished. Terminal boards with belt loops are furnished to provide a
convenient means of making the necessary connections between shoe cleats and the Receiver.
E. Battery Replacement
See photo illustration.
IV. Instructions for Unpacking and Inspection
Note the placement of the various components as received and repack in the same manner when not in
use. If damage has occurred in shipment, file a claim with the carrier immediately. If it is necessary to contact your
supplier or the manufacturer concerning damaged or missing items, be sure to include all the information such as
serial number, purchase order number and invoice number. This will assure you of obtaining proper and expeditious
service.
1. Turn PD Instrument off.
2. Locate battery compartment on right-hand side of the
instrument.
3. Lift and push compartment door until it opens.
4. Pull out door and replace single 9 volt battery. T&R #010-007
5. Push door back into place until it’s secure.
6. Resume instrument operation.

- 4 -
Sponsoring members of NACE International, NACE Foundation QMF-570 104-154
PRODUCT INSTRUCTIONS
V. Operating Instructions
A. Pearson Survey(Also see condensed Operating Instructions)
The following components are required for a Pearson Survey of a buried pipeline:
1. Oscillator with connecting cables
2. Twelve-volt storage battery (not furnished)
3. Receiver
4. Two sets of shoe cleats
5. Cleat connecting cables
6. Terminal Boards
The audio Oscillator is placed along the pipeline at a point where an electrical connection can be made to
the pipe. Test point lead wires are convenient connections. The pipe lead wire is connected to the terminal of the
Oscillator marked PIPE. Connect a wire from the terminal marked GROUND to some metal structure, which is in
good electrical contact with the earth. If no structure is available, a rod can be driven into the earth at a point from
20 to 30 feet from the pipe at right angles to the pipeline.
Connect a 12-volt storage battery to the battery terminals, observing correct polarity (red is positive or +,
black is negative or -). Set the output voltage switch to 2.5, the interrupter switch to “OFF”, and the battery switch
to “ON”. The Fine Adjust knob should be advanced all the way to the Right (MAX). Next, advance the output
voltage control until the LED lights on the Oscillator show Red. Then move the Fine Adjust knob to the Left (MIN)
until the LED lights show Green.
NOTE: Model PD-C (Rev. B) uses a new crystal that produces an interrupt frequency at a faster rate than
previous models. Users familiar with this instrument may notice the difference.
If overloaded, circuit breaker will trip. To reactivate, reduce driving voltage and reset circuit breaker.
Turn the interrupter switch “ON”, if desired, and the Oscillator is ready for use.
For the most recent Oscillator, PD-C (Rev. B), the instructions are:
1. Connect 12 volt battery, observing polarity.
2. Connect to pipe and ground. Output Voltage to 2.5, Fine Adjust all the way to the Right (MAX).
3. Interrupter to OFF. Battery to ON.
4. Advance Output Voltage until Red LEDs light. Move Fine Adjust towards MIN until Green LED lights.
5. Interrupter to ON. Instrument is now ready for use.
NOTE: Model PD-C (Rev. B) uses a new crystal that produces an interrupt frequency at a faster rate than
previous models. Users familiar with this instrument may notice the difference.
The terminal boards should be attached to the belts of the operators. (The board with the cord and plug is
used by the operator who carries the Receiver). Both operators fasten cleats on their shoes, then attach cleat cable
to each cleat, running the cables inside their pant legs. The key operator connects with wires from both of his cleats
to the lower terminal on his terminal board. The secondary operator connects the wires from both of his cleats to
the lower terminal on his terminal board. The secondary operator connects the wires from both of his cleats and
one end of the long connecting cable to his terminal board. The other end of the connecting cable goes to the
upper terminal of the key man’s terminal board. The plug coming from the key man’s terminal board is plugged into
the jack marked CLEATS, the Receiver is turned “ON”, and the apparatus is ready for use.
Tel: [phone]
2828 FM 758 New Braunfels, TX 78130 92402
Web: www.tinker-rasor.com E-mail: [e-mail]

Tel: [phone]
2828 FM 758 New Braunfels, TX 78130
Web: www.tinker-rasor.com E-mail: [e-mail]
- 5 -
Sponsoring members of NACE International, NACE Foundation QMF-570 104-154
PRODUCT INSTRUCTIONS
The traverse along the pipeline is made by walking over the pipe at a slow pace. Beginning adjacent to the
Oscillator set the Receiver volume so that the signal from the Oscillator can be heard at a very low level. As
progress away from the Oscillator is made, the signal may drop and the level can be raised again by increasing the
volume. A discontinuity is indicated by an increase in average signal level, followed by a relatively sharp decrease,
then another increase and then back to normal level as progress is made over the discontinuity.
The exact point of discontinuity lies under the point of decreased signal or null. This, then, is the point
halfway between the two operators. If a series of discontinuities exist in close proximity to each other, the null effect
may not be heard, or very difficult to observe. In this case, one man walks along the line and the other walks at
right angles to the line and a discontinuity is noted by an increase in signal directly over the fault.
B. Locating Shorts or Contacts
The following components are required for locating line shorts:
1. Oscillator and battery
2. Oscillator to pipe cable
3. Remote ground connection
4. Receiver
The Oscillator and ground connections are made in the same fashion as described in the Pearson Survey
above.
Turn on the Oscillator and Receiver. Advance the Receiver sensitivity control until the 750 Cycle tone is
heard in the loudspeaker and the signal intensity meter reads slightly less than full scale. As the Receiver is moved
back and forth across the pipe to which the Oscillator is connected, a very sharp decrease, or null, in the received
signal will be observed when the Receiver is directly of the pipe. Using this null method, it is possible to trace the
path of the pipeline as long as there is a relatively large amount of audio-current flowing in it. If the coated pipe is
in contact with a foreign system, the audio-current will leave the coated pipe at this point and audio-current will flow
in the foreign system. The same null effect will then be present on the foreign system as on the coated pipe from
audio Oscillator to point of contact.
C. Locating Pipelines
The apparatus and method required for locating welded or screwed pipe, is the same as for locating shorts
or contacts. After connecting the Oscillator, hold the Receiver level over the ground and note the intensity of the
received signal. As the Receiver is brought near the pipe, the signal will gradually increase and then will null sharply
as the Receiver passes directly over the pipe.
It is also possible to determine the depth of a pipe. First mark its exact center, using the method described
above. Once the centering of the pipe has been accomplished, it is relatively easy to measure the depth by
triangulation. In order to determine the depths of pipes, it is necessary to position the Receiver in a 45°angle to
the ground surface. This is accomplished by holding the Receiver so that its longest axis is perpendicular to the
path of the pipe and then tilting it back until the air bubble in the depth angle gauge lies between the outer edge of
the center ring and the black border.

Tel: [phone]
2828 FM 758 New Braunfels, TX 78130
Web: www.tinker-rasor.com E-mail: [e-mail]
- 6 -
Sponsoring members of NACE International, NACE Foundation QMF-570 104-154
PRODUCT INSTRUCTIONS
Starting at the point directly above the pipe centerline, and keeping the Receiver as close to the surface as
possible without scratching it on the ground, move slowly away from the pipe at a right angle, maintaining the
Receiver at 45°. When a new null or minimum signal is obtained, the depth of the pipe below the surface is the
same as the distance between the centerline of the pipe and the leading edge of the Receiver.
104-154