Hytronik HC034RF Quick guide

1. Technical Specifications
Product type RF wireless microwave motion sensor (tri-level control)
Operating voltage 220~240VAC 50/60Hz
Power consumption < 1.5W
Detection angle 360o
Detection area (Max.)*
Detection range 10% / 50% / 75% / 100%
Hold time 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min
Stand-by time 0s / 10s / 1min / 5min / 10min / 30min / 1h / +
Stand-by dimming level 10% / 20% / 30% / 50%
Daylight threshold 2 ~ 500Lux, Disable
RF transmission distance 30 meters in the open area
RF frequency 868MHz (FSK mode)
Warming up time 20s
Operating temperature -20oC ~ +50oC
IP rating IP65
8
2. Installation
Warnings:
1. Installation must be carried out by a qualified engineer in accordance with local
regulations.
2. Disconnect power supply before installing.
3. Install to a solid surface - vibrations may cause mis-triggering.
4. Ensure environmental conditions are suitable for electronic equipment
Rotary switch
for RF grouping
HC
034RF (RF receiver)
RF antenna
Infrared remote receiver 1-10V+
1-10V- L’ NNL
71.5
4.2
37.5
38.3
25
11.8
78.2
87
Installation hole
Installation and Instruction Manual
HIGH BAY RF WIRELESS MICROWAVE MOTION SENSOR HMW38/RF + HC034RF
HF
HMW38/RF-20181220-A1
Product type RF wireless receiver
Operating voltage 220-240V 50Hz
Rated load Capacitive:400W; Resistive:1200W
IP rating IP20
3. Rotary Switch for RF grouping
4. Functions
Hytronik builds this function inside the motion sensor to achieve tri-level control, for some areas
it requires a light change notice before switch-off.
It offers 3 levels of light: 100%-->dimmed light-->off; and 2 periods of selectable waiting time:
motion hold-time and stand-by period; Selectable daylight threshold and freedom of detection
area.
4.1 Tri-level Control (Corridor Function)
15 channels are available for fast grouping via rotary switch on both HMW38/RF and HC034RF.
By simply selecting the same channel on each unit, the grouping is automatically completed.
Noted:channel "0" is not for fast grouping, and sensors can only be grouped by remote control.
The built-in daylight sensor can read ambient natural light and switch off the fixture automatically
whenever artificial light is not required (natural light lux level exceeds daylight threshold).
Note: if the stand-by time is preset at "+∞", the fixture never switches off even when natural light
is sufficient.
4.2 Lux Off Function
The light will flash ONCE rapidly after receiving the command from the remote controller.
Note: There is no load indication (the light will not flash) when button ON/OFF, POWER
100% or POWER 80% is pressed.
4.3 Load Indication
commander receiver
HMW38/RF
HC034RF
Rated load
A. Ceiling mount
B. Screw to the Luminaire by conduit
C. Attach to the shade by clamp
91.5
59.3 57.3
47.5
4.1
80.7
75
4.1
66.6
81.5
59.6
66.6
89.9
0.825”
75 64
59.3 57.3
35.2
47.5
Sensor module
Daylight sensor
LED indicator Infrared receiver
Rotary switch
Angle adjustment
Luminaire clamp
Sensor module
Daylight sensor
LED indicator
Infrared receiver
Rotary switch
Cable entry
Sensor module
Daylight sensor
LED indicator
Infrared receiver
Rotary switch
Cable entry
Installation rack
84.5
59.3
ぶ
29
163.2
66.6
75
33.7
15
28.5
4.5
ぶ
4.5
59.6
Installation Height : 20m (forklift) 15m (person)
Detection Range (Ø) :20m
24.5
1000W (resistive);
800VA (capacitive)

8. Descriptions of the Button Functions
(remote control HRC-11)
HMW38/RF-20181220-A1
6. Wiring Diagram
HMW38/RF
Brown
LED driver
L
N
1-10V+
1-10V-
L
N
Blue
Grey
Red
Black
5. RF grouping
Step1
The receiver unit
Beeper is on for 3min
Short press “Learn/Erase” button on RC to the receiver to activate pairing mode, and
the receiver unit will beep once every second for 3min.
Note: up to 30 units can be paired.
Step2
Beeper beeps rapidly beep 3 times in 1s
when RF signal is received successfully
Step3
The receiver unit
Beeper is on
Short press “Transmit” button on RC to the commander, the red indicator on
commander unit will flash for 3 times to send the transmission signal.
The receiver unit
HC034RF
HC034RF
LED driver
Upon receiving the transmission signal, the indicator on receiver unit will flash quickly then
slowly to indicate the success of pairing. One more short press on “Learn/Erase” button to the
receiver unit to complete the pairing process, the receiver unit will quit the pairing mode.
Erase:
Long press “Learn/Erase” button for 3s to the sensor unit, the indicator rapidly flashes 12
times, all commands that it has received before will be erased.
HRC-11
&
A
4 hh
4
h
1
3
7
9
6
8
10
11
12
13
14
2
4
5
&
A
4hh
4
h
Short press ”Learn
/Erase” button
&
A
4hh
4
h
Short press ”Learn
/Erase” button
Short press
”Transmit” button
&
A
4hh
4
h
The commander unit
LED indicator flash 3 times
10%
30%
75%
50%
Ceiling mounted detection pattern (m)
Ceiling mounted height(m)
10
0
20
Detection Pattern7.
* For single person walking across, the detection range is reduced by 1/3.
(forklift)

9. Troubleshooting
YDEMERESUACYDEMERESUACNOITCNUFLAM
The fixture does not light up
The fixture is always on
Check detection area setting
The fixture is on when it should not
Incorrect daylight threshold setting
Continous movement in the detection zone
Sudden change in temperature due to weather (wind, rain, snow)
or air expelled from fans, open windows
Detection zone not targeted
Faulty fixture
No power supply
Adjust daylight threshold setting
Replace fixture
Check power to sensor
Check detection area setting
Adjust zone, change installation site
Detection range [ zone ]
Press buttons in zone to set detection range at 100% / 75%
/ 50% / 10%.
Note: Disabled for HC034RF.
8
8
Scene prog. [ zone ] (One-key-commissioning)
1. Press button “start” toprogram.
2. Select the buttons in “Detection range”, /“Daylight
hreshold”, “Hold time”, “Stand-by time”, “Stand-by
dimming level” to set all parameters.
3. Press button “Memory” to save all the settings programmed
in the remote control.
4. Press button “Apply” to setthesettings to each sensor unit(s).
For example, topre-set detection range 100%, daylight
threshold Disable, hold time5min, stand-by time+∞,
stand-by dimming level 30%, steps should be:
Press button Start, button 100%, Disable, Shift,
5min, Shift, +∞, 30%, Memory. Bypointing to
the sensor unit(s) and pressing Apply, all settings are
passed on the sensor(s).
7
7
77
3
3
8
8 9
10
10
11 1312
11 12 13
Permanent ON/OFF [ ]
Press button ,to select permanent ON or permanent OFF mode.
* Press button / to resume automatic operation.
The mode will change to AUTO Mode after power failure.
Power output [ button ]
Press button , the light output shifts between 80% and 100%.
Note: the function of “Sensor off” and “Twilight” are disabled.
button
Auto Mode [ button ]
Brightness +/- [ button ]
Press button to adjust the lightbrightness between 10%~100% .
Shift [ button ]
RESET[ button ]
Press button to initiate automatic mode. The sensor starts
working and all settings remain as before the light was switched
ON/OFF.
Note: the function of semi-auto is disabled.
Press button , the LED on the top left corner will flash to indicate
mode selection.
All values / settings in RED are valid for 20 seconds.
1
2
3
3
4
4
5
6
6
5
1
24
Ambient daylight threshold [ button ]
1. Press button Shift, the red LED is on for indication.
2. Press button , the ambient lux level is sampled and set as
the new daylight threshold.
3
10
Stand-by dimming level [ zone ]
Press buttons in zone to set the stand-by dimming level at 10% /
20% / 30% / 50%.
Note.the function of 24h / 12h / 4h / 30s are disabled.
13
Dual tech & RF mode [ zone ]
1. HF, PIR, HF+PIR, HF/PIR are disabled.
2. Short press button "Learn/Erase" to activate pairing mode on all
receiver (slave) units to be paired.
Note:up to 30 units can be paired.
3. Short press button "Transmit" at the commander unit(master), the
LED will flash for 3 times to indicate that the transmission signal has
been sent. The receiver units will rapidly beep 3 times in 1s to indicate
the success of pairing.
4. Long press “Learn/Erase” button for 3s, and the receiver unit
clears all commands it has received before.
5. Press button RX100%, the light on receiver unit is 100% on upon
receiving RF on signal; Press “RX STBY%” button, the light(s) goes
to presset stand-by dimming level directly.
14
13
10
Daylight threshold [ zone ]
Press buttons in zone to set the daylight sensor at 2Lux /
10Lux / 50Lux / 100Lux / 300Lux / 500Lux or Disable.
Note: 1. To set daylight sensor at 100Lux / 300 Lux / 500Lux,
press button Shift at first.
2.
Disabled for HC034RF.
9
9
3
Stand-by time [ zone ]
Press buttons in zone to set the stand-by period at 0s / 10s /
1min / 5min / 10min / 30min / 1h / +∞.
Note: “0s” means on/off control; “+∞” means bi-level control,
100% on when motion detected, and remains at the stand-by
dimming level when no presence is detected after hold-time.
Hold time [ zone ]
Press buttons in zone to set the hold time at 2s / 30s / 1min /
5min / 10min / 15min / 20min / 30min.
Note: 1.To set hold-time at 30s / 5min / 15min / 30min, press
button Shift at first.
2. 2s is for testing purpose only, stand-by period and
daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button or any button in zone .
3
11
12
12
11
11
2
HMW38/RF-20181220-A1
Hytronik Industrial Ltd. | www.hytronik.com
3rd Floor, block C, complex building, 155#, Bai'gang road south,
Bai'gang village, Xiao Jin Kou town, Huicheng district, Huizhou 516023
Tel: [phone] Fax: [phone]
Press button , all settings go back to the default setting：HMW38RF:Detection range:100%, hold time:1min,
stand-by time:5min,stand-by dimming level:20%,
daylight sensor:lux disable, RX 100%
2
HC034RF: Detection range:100%, hold time:10min,
stand-by time:30min,stand-by dimming level:20%,
daylight sensor:lux disable, RX 100%