TinyMOS TINY1 User manual

TINY1 Handbook
Welcome

What’s in the box
TINY1 camera 4mm standard lens Micro-USB cable 2.8mm wide-angle lens
(optional)
Optional accessories
solar lter100mm
telephoto lens
telescope
adapter
canon/nikon
adapter
mini tripod
get them from tinymos.com/get-tiny1

shutter button
on/off button
camera strap hole
1/4” tripod mount
camera strap hole
3.5mm headphone jack
3.5mm microphone jack
microSD slot
micro-usb 2.0 port
accessory port lens mount
microphone
TINY1 camera body

1
Contents
Charging 2
Lenses 3
- 4mm standard lens 4
- 2.8mm wide-angle lens 5
- 100mm telephoto lens 6
- Solar lter 7
- How to attach lenses 8
Turning on the camera 9-10
Onboarding
- Introduction 11
- Remove Sticker 12
- WiFi 13
- Timezones 14
- Search 15
- Auto & Manual Modes 16
- IR Pass 17
- Basics 18
Auto Mode 19-22
Manual Mode 23-25
Swipe-down Menu 26
Overlays 27-28
Taking Photos 29
Transferring les
- via microSD 30
- via USB 31
Settings
- Photo Settings 33
- Video Settings 33
- Imaging Settings 34
- General Settings 35-36
- Wi Settings 37
- Location & Time Settings 37
- Custom Settings 38

2
Charging
Connect TINY1 to a power outlet with the included cable and a
USB power adapter (not included)
The on/off button will light red when it is charging
Red light/Flashing Charging
Off Charging completed
*Please use a power adapter that is rated at least 2A at 5V
**Power adapters below 2A may not be able to charge the camera
Please note that most computers are unable to provide the
required power
Locate the micro-USB port on the camera
under the rubber cover
Recommended charging duration before use: 1 to 2 hours

3
TinyMOS lenses
4mm standard lens 2.8mm wide-angle lens 100mm telephoto lens
These are the lenses that we sell. The 4mm standard lens comes with every TINY1 camera.
All TinyMOS lenses are manual focus only.

4
4mm standard lens
TinyMOS 4mm f/1.2 lens
focus ring
lens mount
The standard lens is equivalent to a 28mm lens on a full-frame camera

5
2.8mm wide-angle lens
TinyMOS 2.8mm f/1.2 lens
focus ring
lens mount
The wide-angle lens is equivalent to a 20mm lens on a full-frame camera

6
100mm telephoto lens
The telephoto lens is equivalent to a 700mm lens on
a full-frame camera.
The wide end of the lens is meant to search for
objects as it would be difcult to search at the
telephoto end.
Use the maximum telephoto end to take photos as
the rest of the zoom range is unable to focus.
The aperture ring controls the amount of light that
reaches the camera sensor.
TinyMOS 100mm f/2 lens
zoom ring
focus ring
aperture ring
lens mount
TTelephoto
WWide
FFar
NNear
Solar Filter
The 100mm f/2 lens is compatible with the solar
lter, which allows you to capture images of the sun.
Note:
On newer lenses, when you turn one of the rings
(aperture/zoom/focus), other rings may turn as well.
The effect will be reduced with use.

7
Solar lter
To attach the solar lter to the lens, place it over the front of the lens and press it in.
Newer versions of the 100mm lens will require the use of a 40.5mm UV lter (included) to use the solar lter.
WARNING: Do not look through the solar lter with your eyes as the lter is not eye safe.

8
How to attach lenses
To attach a lens to your camera, place the lens on the lens mount and twist it clockwise until it is tight.
To remove the lens, hold the lens rmly and twist it anti-clockwise until it is out.
Do not force the lens in. You may damage the threads on the camera or lens.

9
Locate the on/off button on top of the camera.
Press and hold the on/off button for 3 seconds.
The screen will light up, and the boot screen will appear.
During the initial bootup, the screen is very dim, and it will
take approximately 1 minute to completely turn on.
Press the on/off button once to set the camera to sleep.
Press and hold the on/off button for 3 seconds, then select
‘Power Off’ to turn it off.
Turning on the camera
If you are unable to turn on your camera, try charging it for at least 3 hours before powering it on.
Alternatively, try holding the power button down for 40 to 60 seconds before releasing.

10
Turning on the camera
This is what the screen should display when the camera is turning on.
For the rst boot up, you will be asked to connect to WiFi and set the timezone.
This step is necessary for the operation of the GPS.

11
Onboarding: Introduction
You should see this screen once the camera is turned on. Tap continue to connect to WiFi.

12
Onboarding: Remove Sticker
Please remove the sticker over the sensor to allow the camera to capture images properly.

13
Onboarding: Wi
Select your WiFi network. You will be prompted for the password if required.

14
Onboarding: Timezones
Select your time zone. This step is necessary for GPS operation.

15
Onboarding: Search
Using the search function, you can look for planets, stars, messier objects, and more.
GPS is required to use this function.

16
Onboarding: Auto & Manual Modes
By default, the camera is set to Auto mode. You may change this setting by bringing down the
swipe-down menu and switching to Manual mode.

17
Onboarding: IR Pass
Switch between IR pass and IR cut from the swipe-down menu.