Titan LED Silver Series User manual

850 East Covey Lane, Suite #140, Phoenix AZ 85024
Phone: [phone] FAX: [phone] WWW.TITANLEDUS.NET
Canopy Style Solid State Luminaire
INSTALLATION MANUAL
For Titan LED Silver Series Canopies
(120 - 277V) (277 - 480V)

BEFORE INSTALLATION PLEASE READ ALL PRODUCT LABELS AND INSTALLATION INSTRUCTIONS
THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN FAMILIAR WITH THE CON-
STRUCTION AND OPERATION OF THIS TITAN LED PRODUCT AND OF ANY HAZARDS INVOLVED
INSTALLATION MUST BE IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND ALSO ALL
RELEVANT LOCAL CODES
WARNING: IMPROPER INSTALLATION WILL VOID THIS PRODUCTS WARRANTY
WARNING: TO AVOID RISK OF ELECTRICAL SHOCK DISCONNECT A/C POWER AT CIRCUIT
BREAKER POWERING JUNCTION BOX BEFORE PERFORMING ANY A/C ELECTRICAL
TASKS
TITAN LED FIXTURE WIRING DESCRIPTION:
BLACK WIRE: AC LOAD / LINE / HOT
WHITE WIRE: AC NEUTRAL
GREEN: AC GROUND
CAUTION: EXISTING WIRING SHOULD BE CHECKED BEFORE INSTALLATION TO INSURE
CORRECT WIRING POLARITY AND CORRECTLY FUNCTIONING GROUND. EXISTING
LUMINAIRE REPLACEMENT NECCESSITATES CAREFULLY REMOVING BULBS AND
THEN THE LUMINAIRE
CAUTION: HID LAMPS AND BALLAST ARE FOUND TO CONTAIN SUBSTANCES HAZARDOUS TO
HUMANS AND WILDLIFE. SOME BALLAST CONTAIN POLYCHLORINATED BIPHENYLS
ALSO KNOWN AS PCB’S. PROPER HAZARDOUS MATERIAL DISPOSAL IS REQUIRED
CAUTION: TO AVOID THE RISK OF ELECTRICAL SHOCK, ALLOW 5 MINUTES AFTER DISCONNECT
FROM A/C POWER TO DRAIN CAPACITOR FIELD CONTAINED IN FIXTURES LED
DRIVER
ank You for your purchase of Titan LED’s LED lighting Product. Please take a moment to read this guide
and familiarize yourself with this State of the Art Solid State LED product.
Please Observe All Safety Precautions Before Installation.
CAUTION: DISCONNECT ALL A/C POWER BEFORE LIGHT
FIXTURE INSTALLATION
CAUTION! SAFETY WARNINGS:
UNPACKING YOUR NEW TITAN LED LIGHTING FIXTURE:
CAREFULLY REMOVE LIGHTING FIXTURE FROM PACKAGING CHECKING FOR ANY
SIGNS OF DAMAGE
ATTENTION: UPON REASSEMBLY THE FIXTURE, PLEASE BE CAREFUL TO ROUTE INTERNAL EX
CESS A/C AND LOW VOLTAGE CABLING AWAY FROM THE INTERNAL ACC FAN WHEN
CLOSING MOUNTED FIXTURE.
ATTENTION!
When wiring xture for 480V Dual Phase
The white neutral leg is used for the 2nd
phase load connection.
All information and images are the exclusive property of Titan LED Inc. 2018 and may not be used without permission.

ATTENTION: LUMINAIRE MUST BE MOUNTED IN ACCORDANCE WITH LOCAL
AND NATIONAL BUILDING CODES
MOUNTING:
1) IT IS REQUIRED TO USE THE PROPER OPTIONAL WEIGHT RATED HARDWARE TO SECURLY
AND SAFELY INSTALL THIS LIGHTING FIXTURE.
2) REMOVE CANOPY FIXTURES COVER AND FLUSH MOUNT TO A SECURE HORIZONTAL
OVERHEAD LOCATION USING HIGH GUAGE SHEET METAL SCREWS THAT ARE PROPERLY
RATED FOR WEIGHT CAPABILITIES. THE 3/4” HOLE IN THE LID OF THE CANOPY CAN ACCEPT
A STANDARD 3/4” NPT TYPE FITTING. PLEASE ADHERE CLOSELY TO ALL HARWARE INSTALLATION
GUIDELINES TO INSURE PROPER SAFETY AND OPERATIONAL FUNCTIONS.
CAUTION: PROPERTY DAMAGE, SERIOUS INJURY, AND OR DEATH MAY OCCUR FROM IMPROPER
INSTALLATION OF THIS LIGHTING FIXTURE.
CAUTION: THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN FAMILIAR WITH
THE CONSTRUCTION AND OPERATION OF THIS TITAN LED PRODUCT AND OF ANY
HAZARDS INVOLVED.
3) RE-ATTACH THE FIXTURE AT THE HINGES. ONCE THE FIXTURES COVER IS SECURELY MOUNTED
THIS FIXTURE MAY HANG OPEN AT HINGES WHILE MAKING ELECTRICAL CONNECTIONS.
4) CONNECT THE A/C POWER SUPPLY WIRES TO THE LUMINAIRES DRIVER CONNECTION WIRES FOUND
INSIDE THE CANOPY HOUSING WITH THE BLACK WIRE BEING THE A/C LOAD (HOT), THE
WHITE WIRE BEING A/C NEUTRAL AND THE GREEN WIRE BEING A/C GROUND.( See Pic Below )
5) AFTER INSPECTION OF PROPER AND SECURE A/C CONNECTIONS CLOSE FIXTURE AND REPLACE THE
FIXTURES 2 ACCESS SCREWS.
6) YOU CAN NOW RESET THE MAIN POWER CIRCUIT AT THE BREAKER.
YOU CAN NOW POWER ON THE NEW LIGHTS.
7) LOW VOLTAGE 0-10V DIMMING IS AN OPTION BUILT INTO TITAN LEDS DRIVERS (POWER SUP-
PLIES) THESE LOW VOLTAGE DIMMING WIRES ARE COLORED PURPLE (dim +) AND GREY (DIM -)
AND WILL OPERATE WITH 0-10V LOW VOLTAGE DIMMER SYSTEMS ONLY.
8) IF DIMMING CIRCUIT IS NOT TO BE USED, LEAVE THE PURPLE AND GREY WIRE LEADS
SEPERATELY CAPPED AND UNCONNECTED.
INSTALLATION INSTRUCTIONS:
Titan LED Canopy lights have a built in top side pre-cut hole in e Top Cover to accept a Standard 3/4” Pipe
Connection. Properly utilizing this hole with the right adaptors for a thread tight installation helps safety and
increases the lights moisture barrier in typical applications.
0-10v Low Voltage Dimming
Wires are Purple + and Grey -
Titan LED’s Hinged Canopy Fixture Cover Shown Below
Dimensions: