TKK systems EG-6CP0S-4 User manual

1
DNVR（Digital Network Video Recorder）
USER MANUAL
EG-6CP0S-4
EG-6CP0S-8
EG-6CP0S-16
EG-6CP1S-16
EG-6CP2S-32
Before using this system, please read the user manual

2
carefully.
Attention:
*Don’t use the system at place with high humility or dust or dirty.
*Avoid direct sunshine or being heated.
*Leave the system away from magnetism objects.
*Avoid high or low temperature(recommended temperature range: 5°C-35°C).
*Close the system before installing the hardware and software.
*Don’t place the system at some place where will likely have a shake.
*Please use it at the aeration place.
*Radio, television or wireless communicate device could cause damage to the
system.
*Don’t dismantle the system by yourself freely.
*Don’t put heavy object on the system.
Table of Content
Attention 2
Chapter 1. Product overview 3
1.1 Products features 3
1.2 Hardware requirement 4
1.3 Software requirement 4
Chapter 2. Install the system 5
2.1 Installdriver 5
2.2 Installsoftware 6
2.3 Apply for DDNS and p2p account 6
2.4 Channel number and draw mode selection 7
Chapter 3. Operate Main system 9
3.1 Log onsystem 9
3.2 Main screen of server 9
3.3 Setup 11
3.3.1Localusermanagement 11
3.3.2 Setup record with audio 12
3.3.3 Preview 13
3.3.4Record 13
3.3.5Alarm 14
3.3.6Schedule 17
3.3.7PTZ 18
3.3.8 Authorization(network user) 18
3.3.9Others 20

3
3.3.10Color Scheme 21
3.3.11 TV out 22
Chapter 4. Playback 22
Chapter 5. Remote view 25
5.1 Remote view by client software 25
5.2 Remote view via IE 27
5.3 Mobile view 28
Appendix 1. Auto login and auto run schedule setting 30
Appendix 2. Monitor audio and record audio synchronous 31
Appendix 3. Internet Explorer browser setting 33
Appendix 4. Pre-set setting 34
Chapter 1. Product overview
1.1 Products features
zRun under Windows XP 32bit OS, Windows Vista 32bit OS;
z6805 chipset 10-bit ADCs image quality;
zLightning-Proof design;
z6805 chipset could display in real time or not real time, if you choose one
channel each chipset, then the display will be real time. And if you
choose two, three or four channels each chipset, then the display will be
not real time;
zAdjust the setting for any channel, and can be applied to other
channels;
zSnapshot the dynamic picture or static picture while playback;
zDisplay, record, playback, control, backup can be done simultaneously;
zSnapshot picture for single frame or snapshot picture for all frames while
live displaying;
zMotion detection, alarm function;
zSupport different types of high speed dome, PTZ controller and alarm
decoder;
zHigh quality network transmitting function;
zRemote view, playback, PTZ control, through Wan or LAN;
zSearch by the date, time, location, alarm period, snapshot pictures;
zComplete automatically operation: user can set record schedule for each
camera within all the periods of each week; and the system will record
according to the schedule;

4
zUser can set alarm activation schedule for each alarm sensor within all
the periods of each week, the alarm sensor will activate according to the
schedule;
zUser can set motion detection for each camera within all the periods of
each week, and the motion detection will activate according to the
schedule;
zCircularly switch function; Can set single channel or multi channels to
switch circularly;
zUser-friendly interface, it is easy for user to operate it;
zThe system will show hard disk is full if the hard disk will up to the
capability.
1.2 Hardware requirement
zRAM：512MB or above
zDisplay card: ATI128MB or above,Geforce2 MX400 128MB or
above
zCPU: Celeron D2.8 G or above or Intel P4 2.4 G or above
zResolution of monitor: 1024*768(32bits color)
zHDD: IDE, SATA,SCSI, 80GB or above
zMotherboard: Intel Chipset 865 or above
1.3 Software requirement
zWindows 2000/Windows XP/Windows Vista 32bit OS
zDirectX 9.0
zThe latest driver for display card
Attention: before installing the driver of display card, please install the driver of
motherboard; otherwise it will affect the function of display card and video
surveillance system

Chapter 2. Install the system
2.1 Install driver
2.1.1. Insert the CD into CD/DVD-ROM, it will pop up a installation guide
window, shown as below:
Select Installation Driver option, it will pop up the driver installation window:
2.1.2. Click on Install button to install the driver, and it will show: Installing
driver, please wait…
5

2.1.3. Wait for about 30 seconds, it will show installation finished:
2.2 Install Software
2.2.1 Select Installation Server option, it will pop up the DVR server installation
window:
Click on Install button to begin install the software.
Remark: If you tick “ Install Video Board Driver ” option, it will install the card driver at the same
time while installing the software.
If tick
“ Install Record File Protect Driver ” option, it will install a file protect driver, and you can
not delete the recording file manually. The recording file can only be deleted by the delete tool, or
be overwritten automatically by software while the HDD capacity is nearly full.
Note: For this software, users also can choose to run the software directly
without installation.
(Copy all the files from CD to PC, and run the DVRInit.exe to initialize, run
DVR.exe to run DVR surveillance system.)
2.3. Apply for DDNS and p2p account
2.3.1 First, initialize the software by double click on the DVRInit.exe icon.
Click on initialize button to begin initial. Please wait a moment, it will indicate
6

initialize successfully.
If you want to delete DDNS account, please tick “Delete DDNS account” option,
then it will delete DDNS account at the same time.
If you want to delete p2p account, please tick “Delete p2p service account”
option, then it will delete p2p account at the same time.
2.2.2 After initialization completely double click on DVR.exe icon, and go to the
DDNS and p2p account application interface. You can apply for a DDNS and a
p2p account in this window.
Input a account name and password then click on apply button to apply. After
completely application, it will show application succeeded information on the
top of the window.
Note: If you do not want to use the DDNS or the p2p, you can pass it without
application by click on Next button directly.
If you want to apply for another DDNS account or p2p account, please initialize
the software first, then apply for another one.
Standard: Select the right Video Standard (PAL or NTSC).
7

Remark: This series cards adopt 6805 chipset, and one chipset can support 4 channels at max. So,
there are 4 options of Channels/Device. The default is 2 channels/Device.
Take a EG-6CP0S-4 for example,
the default is 2, so it will show 2 channels in software by default.
If you choose 1 here, it will show only 1 channel in software.
If choose 3, it will show 3 channels in software.
And if 4, it will show 4 channels in software
Video Quality: you could ajust it and get different video quality. The default is
the highest.
Draw Mode: For a better compatible with different motherboards and graphic
cards, we provide 5 draw modes to choose. The default mode is mode 1. After
selected mode 1, it will show a live video image in the right window. And it will
pop up a prompt window, show as below:
If the video quality is good, then click on “Yes” button, and go to next step.
If the video quality is not good or you want to try another mode, please click on
“No”, and it will alter to next mode automatically.
After selected the right Video Standard, channels/device, draw mode, and
watched the live video image, click yes to confirm, and click on finish to finish
these setting and enter into the DVR surveillance interface.
Note: If you want to change the channels/device number or draw mode after
finished these setting, please initialize the software first, then set again.
Chapter 3. Operate Main system
3.1 log on system
Click “DVR.exe” under sever folder, user will get following login window:
User ID: admin
8

Password: 1234
Press “OK” and login into the DVR surveillance system.
3.2 Main screen of server
1
9
System setup Playback
Capture picture
Monitor
Circular
i
Run schedule
Other
4: Screen split 4:Lock/Unlock 4: Exit
Note: When the button is selected, it will become red from grey.
2. System setup: click it, user can get following icon to set the preview, record,
alarm, schedule, PTZ, authorization, others as below picture
3. Run schedule: click it, the system will run according to the schedule

4. Playback: playback the recorded files
5. Monitor: Monitor the audio
6. Capture picture: it allows the function of snapshot
7. Circular preview: Auto scan for different channels, the default interval time
is five seconds.
8. Other: contains minimize, user management, remote connect information,
disk status.
9. Preview: choose the channel that you want to preview, click the number, it
will change to preview status when the number color change from grey to
green.
10. Record, alarm: choose the channel that you want to record or start alarm
function, click the channel number, it will start to record or start alarm function
when the number color change from grey to green
11. Color: adjust black/white, brightness, saturation according the actual
situation
12. PTZ: click the PTZ, user could adjust the PTZ setting.
3.3 Setup
3.3.1 Local user management
Click “other” button , and get tool list, click “local user
management”, ”user management” window will pop-up. ”user
management” is only for setting authority of server user, it is different from the
“Network user authorization “ (If user want to remote view through IE ,
user need to set “Network user authorization “)
10

Set the authorization first, then click “add”, type the new user name and
password, then press “ok” to save the setting.
3.3.2 Setup record with audio
Click “record options” under “system setup”, get following interface. Tick
“Record Audio Synchronously” option, and copy to other channels that you want
to record audio synchronously, then save the setting.
11

3.3.3 Preview
Record name: Tick it, while recording, it will show the channel name.
Record time: Tick it, while recording, it will show the system time.
X-axis, Y-axis: Adjust the shown position of the channel name or record time.
Color of time auto brighten: the color will change if record.
Channel name: set the channel name.
Camera ID Position: set the position of the camera ID. Could choose in ”left
top, right top ,left bottom ,right bottom”.
Font: the font of the channel name will be changed if you choose set a font.
Sharpness: The sharpness of record name and record time.
3.3.4 Record
In this part, user can set the video quality for recorded files.
12

CBR: Constant bitrate, select it, the bitrate will not change
VBR: Variable bitrate, select it, the bitrate will change according to actual
situation
Record quality: provide 6 levels of record quality (level 1-6), “best” is
recommended.
Record audio synchronously: record audio while recording video.
Self define video quality: user can define the video quality by himself
Packing interval for recording file: Set the packing interval.
Select storage disk: set the storage location.
Active denoise time range: set the time range to reduce noise, from 18:00 to
8:00 is recommended.
Net trans: set the network transmit quality, provide 5 levels (level 6-11) and
self define transmit frame rate. 5FPS is recommended.
3.3.5 Alarm
13

Basic setup
Video Signal lost: tick it, if any video signal lost, the system will start to record
Motion detection: tick it, if any motion detected, the system will start to
record
Detection level and sensitivity: to adjust the sensitivity of motion detection
(The default level super is the best)
Alarm relay:
Video signal lost alarm sound: tick it, and select an audio file. If alarm is
triggered by video signal lost, you will hear the sound you have selected
Motion detection alarm sound: tick it, and select an audio file. If alarm is
triggered by motion, you will hear the sound you have selected
Post-alarm time: set the post-alarm time.
Post-record time: set the post-record time.
Detection area
14

The default area is the whole area (in the yellow square). User could clear the
current detection area, and set a different area according to request.
Record Relay: It will be take effect when choose some channels to link-act
recording. For example: set 5 channel to test, link-act record channel is
3,4,5.Once some moving objects in choose area of 5 channel ,then 3,4,5
channels will start to record simultaneously .
15

3.3.6 Schedule
Set the record schedule here.
Basic working mode
S/N Basically work model
Remark
1 Record Continual record.
2 Motion Signal detect If any motion detected, the record will be
triggered, and system begin to record.
3 Record &Motion signal
detection If any motion detected, the record will be triggered, and system begin to record.
If no motion, it is continual record.
How to set: choose channel (for example: channel 1) and date (for example:
Monday), select the default record in the table and click “Edit”, user will get
following information:
16

Enter the start time, end time, and select record type, click “OK” to confirm,
then click on “copy to..” , copy to other days and channels, press “save” to finish
setup.
After finished the setting, go back to the main interface, and Click “run on
schedule” button( ), the button color will change from grey to red, it
indicates the schedule is working.
3.3.7 PTZ
Set PTZ protocol (please confirm with your PTZ camera supplier about the
correct protocol of your camera), the suitable baud rate and address of the PTZ
decode.
3.3.8 Network
17

This option is for network user authorization and trusted IP address.
Trust IP: user could setup accessing IP address, limit accessing IP address by
[add network user][modify IP ] [delete IP], tick the IP address if user don’t want
to limit the IP
18
Set the proper authorization first, then add or modify the user.

3.3.9 Others
This option includes tools which do not list on the toolbar of system setup.
Lock system key: tick it, while running the system, if click on any button of
system, it can not work until unlock the system.
Logon manually: tick it, while click the” dvr.exe”, use has to type user name
and password to logon
Enter windows and auto run: tick it, and set the right windows OS user and
password, the software will auto run after start the PC.
Auto shut down: tick it, and type the interval day and time, the system and
computer will shut down according to the requested time and date
Restart computer: tick it, and type the interval day and time, the system
and computer will restart according to the requested time and date.
Auto run schedule after software started: auto run schedule after DVR
software started.
Mouse auto lock: tick it, and set the time, after the selected time, the mouse
will auto lock.
19

Net trans port: if user allows other user to remote access this server, must
tick it, the default port is 5191.
Web Server port: if user allows other user to remote access this server, must
tick it, the default port is 80.
Remark: If user the default port, while other user remote access the
server, just type the IP address of server, for example:
http://192.168.5.2 . Once user change the default Web Sever port
from 80 to 81, then has to type http://192.168.5.2:81 .
FTP server port: if user allows other user to remote access this server, must
tick it, the default port is 21.
Push warn dialog when disk full: tick it, while the disk is nearly full, it will
have a warn dialog.
DDNS: the secondly domain name in viewnvr.com you applied.
P2P account: the p2p account you applied in software.
3.3.10 Color Scheme
In some area, because of the big change of the lights, the video quality from
camera will change accordingly. To get the better video quality, color scheme is
useful.
Start time: choose the begin time for the adjusted color
End time: choose the finish time for the adjusted color
20
Edit time: make change for above set time