Toa HY-UV08 User manual

INSTALLATION MANUAL
SPEAKER MOUNTING BRACKET HY-UV08
日 本 語 の 設 置 説 明 書 は 裏 面 をご 覧ください 。
Thank you for purchasing TOA’s Speaker Mounting Bracket.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read
all the instructions in this section for correct and
safe operation.
• Be sure to follow all the precautionary instructions
in this section, which contain important warnings
and/or cautions regarding safety.
• After reading, keep this manual handy for future
reference.
Indicates a potentially hazardous situation which,
if mishandled, could result in death or serious
personal injury.
WARNING
• Since the unit is designed for indoor use, do not install
it outdoors. If installed outdoors, the aging of parts
causes the unit to fall off, resulting in personal injury.
• Do not use other methods than specied to mount
the bracket. Extreme force is applied to the unit and
the unit could fall off, possibly resulting in personal
injuries.
• Use nuts and bolts that are appropriate for the
ceiling’s or wall’s structure and composition. Failure
to do so may cause the unit to fall, resulting in
material damage and possible personal injury.
• Tighten each nut and bolt securely. Ensure that
the bracket has no loose joints after installation to
prevent accidents that could result in personal injury.
• Use the specied mounting bracket in combination.
Doing otherwise may cause the unit or component
to fall off, resulting in personal injury.
Indicates a potentially hazardous situation which,
if mishandled, could result in moderate or minor
personal injury, and/or property damage.
CAUTION
• Avoid touching the unit’s sharp metal edge to
prevent injury.
• Do not stand or sit on, nor hang down from the unit
as this may cause it to fall down or drop, resulting in
personal injury and/or property damage.
2. GENERAL DESCRIPTION
The TOA HY-UV08 is the dedicated mounting bracket for
the SR-F08 Speaker system. It allows the SR-F08 to be
mounted in a vertical orientation.
It can be used in conjunction with one of the optional
speaker mounting brackets shown below depending on the
installation location.
For pipe mount use: HY-B0801
For ceiling mount use: HY-C0801
For wall mount use: HY-W0801
4. SPECIFICATIONS
Finish Steel plate, black, semi-glossy, paint
Dimensions 280 (w) x 351.1 (h) x 90 (d) mm
(11.02" x 13.82" x 3.54")
Weight 2.2 kg (4.85 lb)
Accessories For speaker mounting
Hex head bolt M8 x 25
with spring and plain washers ... 4
For bracket mounting
Hex head bolt M8 x 25
with spring and plain washers ... 6
Note: The design and specications are subject to change
without notice for improvement.
3. DIMENSIONAL DIAGRAM
351.1 (13.82")
280 (11.02")
90
(3.54")
Arms
Base
Hands
[Top]
[Front] [Right side]
• Have the unit checked periodically by the shop from
where it was purchased. Failure to do so may result
in corrosion or damage to the unit or its mounting
bracket that could cause the unit to fall, possibly
causing personal injury.
Unit : mm

URL: https://www.toa.jp/
133-01-00264-00
Traceability Information for Europe
Manufacturer:
TOA Corporation
7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo, Japan
Authorized representative:
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg, Germany
Step 1. Remove 4 screws on both sides of the optional
speaker system SR-F08.
Step 2. Attach the hand brackets to the SR-F08's
left and right sides using the hex head bolts
supplied with the HY-UV08.
Note
The screws removed in Step 1 cannot be used.
Step 3. Secure the arms to the base using the supplied
hex head bolts.
Step 4. Attach the left and right hand brackets to the
arms with the supplied hex head bolts.
Step 5. Attach the base to the Bracket B of the speaker
mounting bracket to join.
For attachment, use the 4 hex head bolts
supplied with the speaker mounting bracket to
join.
Note
Use all 4 hex head bolts and securely tighten
them.
Step 6. Using the Bracket A of the speaker mounting
bracket to join, install the speaker to the desired
location.
Note
For the installation of the Bracket A, read the
instruction manual of the speaker mounting
bracket to join.
Step 7. Loosen the hex head bolts installed in Step 4,
and adjust the vertical angle of the SR-F08.
Then, securely retighten the bolts.
5. MOUNTING TO THE SPEAKER
Hex head bolt M8 x 25
(Accessories,
2 each on both sides)
Hex head bolt M8 x 25
(Accessories, 2 places)
4
Arm
Base
3
SR-F08
Tightening torque: 8 N·m
SR-F08
1
* Accessories, 4 places
Hand
Hex head bolt
M8 x 25*
2
Attach the hand bracket aligning its curved line
with the SR-F08's front direction.
Tightening
torque: 8 N·m
5
6
HY-C0801 HY-W0801 HY-B0801
Bracket A
Bracket B
(component of
the HY-C0801,
HY-W0801, or
HY-B0801)
Hex head bolts supplied with
the HY-C0801,HY-W0801, or
HY-B0801 (M8, 4 places)
Tightening torque: 8 N·m
7
Hex head bolt M8 x 25
(accessory, 1 each on both sides)
SR-F08