Tokyo Electronic CS8530D-01 User manual

B/W CCD Camera
CS8530D-01
Operation Manual
CONTENTS
1.PRODUCT DESCRIPTION 1
2.FEATURES 1
3. CONFIGURATION 1
4.OPTION UNITS 1
5.MODE SELECTION 2
6.CONNECTION 4
7.SPECIFICATIONS 5
8.TIMING CHART 7
9.EXTERNAL-VIEW DRAWING 10
Thank you for purchasing our CS8530D-01 B/W-CCD camera. This operation
manual contains many important information such as how to use this equipment
correctly and safely. Please read through this manual carefully. After reading,
keep this manual by the side of your equipment for future reference.
Enter the blank below Product Serial Number, which is found on
bottom/rear chassis of your camera. Keep this number for your record.
Serial No.
TOKYO ELECTRONIC INDUSTRY CO:, LTD.

GENERAL SAFETY INSTRUCTIONS
• This operation manual contains important information for the operator (user)
and/or people around him/her to avoid personal injuries, or property damages
against him/her or people around him/her by using this product correctly.
• Prior to use, read this operation manual carefully to fully understand its
instructions for correct use.
[Definition of markings]
The meaning of each mark used in this instruction manual is given below
DANGER
This mark warns the user that improper use, indicated with this
mark, may cause death or severe personal injuries against the user or
people around him/her.
CAUTION
This mark warns the user that improper use, indicated with this
mark, may cause personal injuries (*1) or material damages (*2)
against the user or people around him/her.
Notes
*1 : Personal injuries mean wounds, burns, electric shocks, and others for which the person
injured need not to be hospitalized nor to be cared for the long term.
*2 : Material damages mean any direct or consequential damages related to property or
material loss.
[This mark indicates what the user SHOULD NOT DO. The details of things which
the user should not do are described next to this mark.
QThis mark indicates what the user MUST DO. The details of things which the user
must do are described next to this mark.
This mark indicates that the user must be alert against a possible DANGER. The
details of the DANGER which the user must be aware of are described next to this
mark.
ÌThis mark indicates that the user are given a CAUTION against possible hazards.
The details of the CAUTION which the user must be aware of are described next to
this mark.
QHandling Precautions
DANGER
Q
If any overheating sign is observed, discontinue the use immediately.
In the event that smoke, smell, or any other overheating sign is observed, turn the
power switch of the system OFF immediately, and remove the camera cable from
the camera connector. Do NOT try to continue to use the camera. To do so in spite
of clear signs of malfunction invites a fire, an electric shock hazard, or a serious
damage to the camera. In such case, contact us or our dealer/distributor from which
you purchased the camera for repair service.
Q
If any malfunctioning sign is observed, discontinue the use immediately.
Do NOT try to use the camera when it is malfunctioning. (Ex. No images on the
monitor) In the event of malfunction, turn the power switch of the system OFF
immediately, and remove the camera cable from the camera connector. In such
case, contact us or our dealer/distributor from which you purchased the camera for
repair service.
Q
If any foreign object gets into the camera, discontinue the use immediately.
In the event that liquids, small particles, or any other foreign objects get into the
camera, do NOT try to continue to use the camera. To do so invites a fire or an
electric shock hazard. In that case, turn the power switch of the camera OFF
immediately, and remove the camera cable from the camera connector. After that,
contact us or our dealer/distributor from which you purchased the camera for repair
service/technical advice.

[
Do NOT disassemble the camera.
Do NOT attempt to pull apart; repair, or modify the camera on your own. To do so
leads to a fire or an electric shock accident. Contact us or the dealer/distributor
from which you purchased the camera for repair/modifacation.
[
Do NOT supply any power than specified.
The camera is designed to work only under specified voltage. Do NOT attempt to
drive the camera with the power other than DC12V. Operating the camera under
power other than DC12V invites a fire or a electric shock hazard..
[Do NOT use the camera in a high-humidity environment.
Do NOT place the camera near a humidifier, or in other high-humidity
environment. To do so may cause a fire or an electric shock accident.
CAUTION
If the camera is operated in the electromagnetic field, there may be cases where
noises (vertical, horizontal, or oblique stripes) may appear to a video output.
In that case, take preventive measures on the electromagnetic-wave generating
source so that the camera do not receive the interference by the electromagnetic-
wave. Take extra precautions against electromagnetic-wave-interference if the
camera is used with a servomotor, inverter, or other electromagnetic-wave-
generating equipment.
Avoid giving a strong shock against the camera. If your camera is used in the
system where its camera connector is subjected to strong repetitive shocks, the
camera connector is possible to break down. If you intend to use your camera in
such a situation, make sure to use an optional-connector-fixing-hardware to
connect the connector-plug to the camera body.
When the camera is not in use, put a lens or a lens-cap onto the cam head so that
the image pickup plane of CCD is protected from dust, foreign object, or other
flaw-causing object. If the glass plane (image pickup plane) gets dirty, clean it with
a cotton swab. When it needs to be cleaned with a cleaner, be sure NOT to use any
organic solvent other than ethyl alcohol.. As a countermeasure against
condensation, when the camera is moved from a warm place to a cold place, take
appropriate precautions to prevent condensation from forming on the camera.
Do not pull strongly the camera cable nor swing it. The stress from pulling or
swinging may cause damage in the coating of the cable, or breaks in the inside
wires.
Avoid short-circuiting its signal output. Otherwise, the camera might be damaged.
If too much amount of light, (= the incoming light amount of 100 times or greater
in comparison with standard light)enters CCD image pickup plane, video output
might not be obtained. In such a case, take measures to reduce the amount of
incoming light.
Do NOT expose the camera to intensive light (sunlight, etc.) to prevent its inner
CCD from gelling damaged.
When mounting a lens, take extra caution so that the lens is not tilled, nor does flaw
exist at the lens-mount-screw part. Also check to confirm that no dirt nor other
foreign object is put inside. Improper mounting might cause the parts to become
locked.

DANGER
[
Do NOT use any optional unit other tan, manufacturer-supplied one. [We disclaim
any responsibility for damages or losses incurred by user due to the use of
unauthorized / unofficial option units supplied by a third party]
[RESTRICTION FOR USE]
In case malfunction of this equipment (e.g. video output cut-off) can be expected to lead to
significant accident, avoid using this equipment for such system integration use.
[CASES FOR INDEMINITY (LIMITED WARRANTY)]
We shall be exempted from taking responsibility and held harmless for damages or losses
incurred by user in the following cases.
* In case damages or losses are caused by fire, earthquake, or other acts of Gods, the act by
third party, misuse by the user deliberately or erroneously, use under extreme operating
conditions.
* In case indirect, additional, consequential damages (loss of expected interest, suspension of
business activities) are incurred as results of malfunction of non-function of the equipment,
we shall be exempted from assuming responsibility for such damages.
* In case damages or losses are caused by incorrect use which is not in line with the
instructions in this instruction manual.
* In case damages or losses are caused by malfunction resulting from band connection with
other equipment.
* In case damages or losses are caused by repair or modification done by the user.
IMPORTANT SAFETY INSTRUCTIONS
(1)This device is designed and guaranteed to work under the temperature range of
0 through 40 degree C. Avoid using the equipment beyond that limits.
(2)Do NOT expose the camera’s image-pickup-plane to sunlight or other intense
light directly. Its inner CCD (charge-coupled device) might be damaged.
(3)In the event that any abnormal condition is observed, turn the power switch
OFF immediately. Do NOT try to continue to use the camera. To do so in spite
of clear signs of malfunction invites a fire, an electric shock hazard, or any
other serious damage to the camera. In such case, contact us or our
dealer/distributor from you purchased the camera for repair service.
(4)To clean the body of this equipment, make sure to torn the power switch OFF
first. To remove stubborn stains, use a soft cloth soaked in diluted acid-free
detergent. After that, clean with a dry cloth.
(5)In case the image-pickup-plane should be settled with fine dust, dirt, of
scratched, ask our distributor for technical advice.

1. PRODUCT DESCRIPTION
Model CS8530D is an integrated (one-body) type B/W CCD camera employing a 1/3
type all-pixel-data-readout CCD. This model has the double-speed driving frequency of
CS8530 to achieve fast-speed data-processing, suited for high-speed and high-
resolution image processing application.
2. FEATURES
(1) Double-speed scan
Model CS8530D reads out image-data twice as fast as conventional
cameras do.
(2) All pixel’s data readout
With its built-in all-pixel-data-readout CCD, CS8530D-01 reads out image-data just
in approximately 1/60 sec.. A frame-shutter reads out all data even under RTS mode.
(3) Random trigger shutter function
Through a built-in RTS (Random Trigger Shutter), the camera’s CCD starts light-exposure
in synchronization with external trigger signals. This function enables the camera to
capture fast-moving subjects at constant position for precise image processing.
(4) Ultra-compact & light-weight camera head
The model features its ultra-compact and light-weight camera head, freeing you from
your integration-space-problem. In addition, it has an excellent resistance against shock
and vibration.
(5) High vertical resolution
As all pixel’s data are read out even in random trigger shutter mode (in
1/60 sec.), images with no deterioration in vertical resolution are obtained.
(6) Square grid pattern CCD
Pixel’s in CCD are aligned in square grid pattern. This makes it easier to perform
computation correctly for image processing use.
(7) External Sync.
The camera is switched over to external sync operation automatically when
external HD/VD signals are input.
3. CONFIGURATION
CS8530D-01
(1) Camera body 1
(2) Accessory
Operation Manual 1
4. OPTION UNIT
(1) DC SYNC IN cable (Dedicated cable) 1
(2) Camera-mounting hardware 1
(3) Camera-connector fixing hardware 1
1

5. MODE SELECTION
(1) GAIN control selection
1 MANU : Manual GAIN volume (Adjustable with a rear potentiometer)
2 FIX : Initial factory-set level
(2) Video output mode selection
1 1/120s MIX: 1/120s Interlace MIX mode
(Under this mode, vertical 2 pixels are added in read-out process.
Images with high sensitivity ate obtained with this mode)
2 1/60s : 1160s Non-interlace mode
(In this mode, all pixel’s data are read out in 1 frame. Images with a
high vertical resolution are obtained with this mode)
(3) Shutter mode selection (Selectable with the rear SW)
1 NOR mode: Normal electronic shutter
High-speed shutter (Initial factory-setting) (1/6000s~OFF, 8 positions)
2 RDM mode : Random trigger shutter
For controlling exposure-time with the pulse-width of external trigger signal
3 R.R mode: Restart & Reset
For outputting images at the timing given by external VD signals
Long-time exposure available
SW1 ON OFF Function
1 M.GAIN FIX GAIN control SW
2 1/60s 1/120sMIX VIDEO OUT mode SW
3
4
5
Refer to (4) Shutter speed
selection (Exposure time) below.
Shutter speed SW
8 steps selection
6 RDM NOR
7 R.R. NOR Shutter mode SW
8 No Setting available (OFF FIXED)
CAUTION
Do NOT set SW1-6 and SW1-7 ON at the same time.
2

(4)Shutter speed selection (Exposure time)
Under NOR mode
The shutter speed of normal electronic shutter is selectable among the ranges shown below.
[Selection with the rear SW]
SW1
3 4 5
Shutter speed (sec.)
OFF OFF OFF OFF (Factory-setting)
ON OFF OFF 1/200
OFF ON OFF 1/500
ON ON OFF 1/1000
OFF OFF ON 1/2000
ON OFF ON 1/4000
OFF ON ON 1/8000
ON ON ON 1/16000
Under RDM mode (Ex-sync only)
The shutter speed is controlled via external trigger signals.
[Selection with the rear SW]
This mode should be used when a wider range of shutter speed with freer
timing than under NOR mode is necessary.
3

Under R.R mode (Ex-sync only)
The shutter speed is controlled via external VD signals
[Selection with the rear SW]
(Make sure to set this SW OFF to operate the camera in other modes)
The shutter speed (exposure time) is determined by the interval of VD signals.
Lower shutter speed than 1/60s, or 1/120s is obtained.
CAUTION
Do NOT set SW1-6 and SW1-7 ON at the same time
6. CONNECTION
Connector pin assignment
Connector used:
DC/SYNC connector---HR10A-10R-12PB Manufactured by HIROSE DENKI
Compatible connector:
DC/SYNC connector---HR10A-10P-12S Manufactured by HIROSE DENKI
1 GND
2 +12V
3 VIDEO.GND
4 VIDEO OUT
5 HD/VD.GND
6 HD.IN
7 VD .IN
8 GND
9 TRIG.IN
10 GND
11 N.C
12 GND
4
Picture: Rear-panel camera connector
(Rear-view)

7.SPECIFICATIONS
Model CS8530D-01
(1) TV system Special format (=Non-conforming to EIA/CCIR)
(2) Image sensor All Pixel’s Data Read-out Interline CCD
(3) Optical size 1/3 type equivalent
(4) Active pixel 659(H) X 494(V )
(5) Unit cell size 7.4(H) X 7.4(V) µm (Square-grid array)
(6) Scanning area 4.789(H) X 3.589(V)mm
(7) Scanning lines 525 lines
(8) Interlace 1/120 : 1/120Hz interlace
1/60 : 1/60Hz non-interlace
(9) Sync system Internal/External automatic switch-over
(10) Scanning frequency 31.468kHz(H)
119.88kHz(V) (1/120s interlace)
or59.94kHz(V) (1/60s non-interlace)
(11) Aspect ratio 4:3
(12) Sensitivity Standard 400 lx F5.6 (Under 1/120s interlace)
(13) Min. illumination Standard 4 lx (F1.4 GAIN MAX)
(14) S/N Standard: 50dB(p-p)/rms (GAIN:FIX)
(15) Video output VS 1.0V(p-p)/75-ohm (AC coupling output)
(16) Resolution 485TVlines(H), 485lines(350TV lines)(V)
(17) Input signal
(1)Ex. Sync. signal HD/VD
Input level HD/VD: From 2 through 5V
HD: From 3 through 10 micro sec. (Negative)
Pulse width
VD: From 125 through 400 micro sec. (Negative)
TRIG
(2)Shutter trigger
(Exposure-starting-cue signal in random trigger shutter mode)
LOW: From 0 through 1V/l0k-ohm
Input level
HIGH: From 4 through 5V/l0k-ohm
Pulse width Longer than 2 micro sec.
(18) Electronic shutter
Normal shutter 8 steps switch-able
RDM TRIG signal pins-width control
R.R. VD signal exposure-time control
(19) GAIN FIX/M.GAIN switch-able
FIX Pre-set gain (Factory-set gain)
M.GAIN Manual gain control
(20) Gamma correction 1 fixed ( Gamma = OFF)
(21) Power source DC12V ± 10 %
(22) Power consumption Approx. 2.2W
(23) Ambient condition Temperature
Operation guaranteed: From –5 through 45 degree C
Performance guaranteed: From 0 through 40 degree C
Humidity
Operation guaranteed: From 10 through 90 percent
(No condensing)
Performance guaranteed: From 10 through 90 percent
(No condensing)
(24) Lens mount C mount
(25) External dimension 31(W) X 29(H) X 70(D)mm (Including lens-mounting part)
(26) Weight Approx. 75g
5

(28) Spectral Response
(29) Optical Black Layout
6

8. TIMING CHART
(1) 1/120s Interlace MIX mode
In this mode, 1/120s interlace video signals are output through VIDEO OUT terminal.
V
IDEO OUT
(2) 1/60s Non-interlace mode
In this mode, 1/60s non-interlace video signals are output through VIDEO terminal.
VIDEO OUT
(3) Random trigger shutter mode (Ex
-
sync only)
In this shutter mode, the camera outputs accumulated (integrated) images at the timing
cued by VD signal input after CCD accumulation(integration) is over. Consecutive
external sync signal input (HD/VD) is available.
[Input signals marked with * below are externally-input signals]
* TRIG IN
* EXTERNAL VD IN
* EXTERNAL HD IN
VIDEO OUT
7

(4) Restart & Reset mode (Ex-sync only)
Set rear panel SW ON. Make sure to set it OFF to let the camera operate under other
mode than RR mode. Shutter speed is determined by VD signal interval.
[Input signals marked with * below are externally-input signals]
T = EXPOSURE TIME
* EXTERNAL
VD IN
* EXTERNAL
HD IN
V
IDEO OUT
8

(5) H rate timing
9

9. EXTERNAL-VIEW DRAWING
Main material: Aluminum die-cast
Finish: Leather-satin
(Cover --- ERIO aluminum; N1.5 leather satin equivalent)
Coating color: Black
10

TOKYO ELECTRONIC INDUSTRY CO.,LTD.
Head Office 4-7-1, Asahigaoka, Hino-shi, Tokyo
191-0065, Japan
Phone: [phone]
FAX: [phone]
E-mail: [e-mail]
Kansai Branch Nitto Building, 2-1-2, Sakaemachi-dori,
Chuo-ku, Kobe, Hyogo 650-0023, Japan,
Phone: [phone]
FAX: [phone]
Fukuoka Office Yen Building, 2-7-21, Hirao, Chuo-ku,
Fukuoka 810-0014, Japan
Phone: [phone]
FAX: [phone]
The design and specification is subject to change without notice.
11