FLIR CM-3304 User manual

Quick Install Guide
Ariel Gen III
CM-3304/CM-3308
4MP/8MP Mini-Dome IP Camera
A. Connect the Camera
1. Insert a cable in the RJ45 connector to attach to
the network switch for a 10/100 Mbps Ethernet and
Power over Ethernet (POE) connection.
B. Discover the Camera
The camera’s web interface can be accessed by
Internet Explorer 10 and higher (32-bit) with the ActiveX
plug-in and by browsers that do not support ActiveX,
such as Microsoft Edge 38 and above, Chrome v.55 or
above, or Firefox v.50 or above, on PCs running 64-bit
Windows 7, 8, 8.1, or 10.
B.1. Configuring the camera on your workstation
for the first time
1. Install the CD in the product package or download
FLIR’s DiscoveryNetwork Assistant (DNA) utilityfrom
the Support > FLIR Firmware & Software Downloads
page at http://www.flir.com/security.
2. Click the DNA icon and run DNA version 2.1.3.15
or higher to log into the unit.
3. Attach the unit to the same LAN segment as the
computer that is managing the unit. DNA automatically
discovers the unit on the network and displays the
device’s current IP address in the Discover List.
4. Select the unit from the Discover List.
5. Select PAL or NTSC by selecting the unit and clicking
Change Video Format from the context menu, or from
the Properties > Device Properties screen.
6. Click Update.
B.2.a Managing the camera with Horizon, Meridian or on
a DHCP-enabled network
If the camera is managed by Horizon configured as a DHCP
server, or is on a network with a DHCP server, the camera
automatically receives an IP address.
1. Open DNA. The unit is automatically discovered on the network.
See section B.1 for instructions how to install DNA.
2. Verifythat the unit is displayed in the Discover List. The unit
status should be displayed as Online and Authenticated.
B.2.b Managing the camera with Latitude or on a network
with static IP configuration
If the camera is managed by Latitude or is on a network without
a DHCP server, manually enter its IP address in DNA.
1. Open DNA. The unit is automatically discovered on the network.
See section B.1 for instructions how to install DNA.
2. If you use non-default credentials, the unit might become
unauthenticated. In this case, authenticate the unit:
a. Use DNA to select the unit(s).
b. Right-click or click the Login button.
c. Enter the camera's User Name ("admin") and Password
("admin").
d. Click Login.
3. In the DNA Assign IP screen, uncheck Use DHCP, and enter
the unit’s IP, Mask and Gateway IP addresses. If the camera
is not authenticated, you must first authenticate it.
4. Click Update.
B.3. Log into the Unit
1. Click the unit in the Discover List. The Login window opens.
2. Enter the default User Name ("admin") and Password
("admin") which are case-sensitive. Then click OK.
3. Click Login in DNA. The unit’s web interface opens.
4. If using IE, click the message to install the ArielPlayer plug-in.
5. Follow the on-screen instructions to install the plug-in.

C. Insert and Configure microSDXC Card
The camera is shipped without a microSDXC card. The card must be inserted in the
camera in order to locally store a snapshot or recording triggered by an event.
To install a microSDXC card:
1. Lift the rubber tab on each side of the dome cover and, using a Torx screwdriver, remove the
dome cover from the camera body.
2. Insert a microSDXC card (up to 128GB, Class 10) in the card drive on the camera’s printed
circuit board.
3. Replace the dome cover.
4. Verifythat the card status is displayed as mounted in the System > Events Handler >
SD Card screen.
5. Format the card.
6. Configure the camera to store snapshots and recordings from the System > Events Source
screens.
D. Mount and Position the Camera
1. Verifythat the operating temperature range is between -40°C ~ 50°C (-40° ~ 122°F),
0-90% relative humidity(non-condensing).
2. Mount the camera at the site according to your surveillance requirements. Be sure to have
the required accessories and tools available.
3. Refer to the User and Installation Guide and mounting accessorydocumentation for
instructions how to install the camera and attach it to the site surface.
4. Set the camera angle and height based on the required Field of View depth and topology.
5. On CM-3304-21-I, click the Lens Control button on the Live screen.
6. Set the zoom and focus on the Lens Control screen.
E. Open Live View
1. Select the Live tab.
2. Set the camera view.
3. Click the red recording icon on the Live screen to start recording.
This step can be set automatically by FLIR’s Latitude, Horizon or Meridian VMS.
F. Attach to Latitude
1. In Latitude, click Physical View on the sidebar.
2. On the Navigation Tree, click the system name.
3. From the Discovery tab, do the following:
a. Under Cameras and Encoders, select FLIR (Latitude 7 and 8).
b. Click Start. The camera details are displayed in the Discoverytable.
c. If the camera was not discovered, click Discover Unit Manually.
d. Enter the camera’s IP address, select FLIR (Latitude 7) or FLIR and Auto Detect
(Latitude 8).
e. Click OK.
4. In the Discoverytable, right-click the camera
5. Select Attach.
6. Click the Archiver name to attach.
7. Click Save.
CM-330x_QIG_30Jul17_v1
FLIR Systems, Inc. 6769 Hollister Ave. Goleta, CA 93117
Tel: [phone] [e-mail] www.flir.com/security