Tokyo Flash KISAI SEQUENCE User manual

Button A
USB Port
Button B
INSTRUCTION MANUAL

Sequence has 2 difficulty settings for telling the time [Regular] & [Cryptic]
You may also choose to display the time in [12hr] or [24hr] modes.
The default setting is [Cryptic] [12hr].
See section 3 “How to set the time” to change your preference.
Press button A once to display the time.
Digits 0-9 in
regular difficulty.
09:34 PM
(12hr time mode)
20:56
(24hr time mode)
I. Regular difficulty mode
1. How to read the time
•
Note: The time will be displayed for 7 seconds.

Digits 0-9 in cryptic difficulty.
Hint: It’s almost the same as regular, but the middle line is
missing. (exception, number 8)
12:36 AM
(12hr time mode)
23:45
(24hr time mode)
II. Cryptic difficulty mode

April 18th = 04 18
(Regular mode)
December 24th = 12 24
(Cryptic mode)
I. Reading the date
2. How to check the date & alarm
Press button A repeatedly to change between Time, Date
& Alarm.
Press button A twice to go directly to date mode.
The Date icon will be displayed.
Note: The date is displayed as MONTH (1-12) followed by DAY (1-31).
•
•
Time Date Alarm
Note: The time, date or alarm will be displayed for 7 seconds.
Date icon

06:45
(Cryptic mode)
08:30 PM
(Regular mode)
II. Reading the alarm
Press button A three times to go directly to alarm mode.
The Alarm icon will be displayed.
•
Alarm icon
PM icon
Alarm [ON] icon

Note: after 7 seconds of inactivity setting mode will deactivate.
3. How to set the time and animation
The hour digits will be flashing.
Press button A to increase the hour.
Press button B to accept.
The minute digits will be flashing.
Press button A to increase the minutes.
(hold A to increase quickly)
Press button B to accept.
While the time is displayed, press & hold button B.
The hour digits will begin flashing & the SET icon will
be lit.
You will be asked to set the following options in sequence.
•
•
•
•
•
•
•
•
•
Hours Mins 12hr/24hr Difficulty Animation
I. Setting the hour
Hours flashing
Minutes flashing
PM icon
SET icon

The display will flash the
current time mode [12] or [24].
Press button A to change the mode.
Press button B to accept.
The display will flash the current time in either [Regular]
or [Cryptic] mode.
Press button A to change between difficulty modes.
Press button B to accept.
•
•
•
•
•
•
III. Setting 12hr / 24hr
IV. Setting the difficulty mode
Press
[Regular] [Cryptic]

Animation mode can be either ON or OFF.
When ON the watch will animate the display every 15 minutes
between 6pm and midnight.
There are 6 different animation patterns to choose from.
The display will show the current animation setting
Press button A to change the setting.
Press button B to accept & finish.
•
•
•
V. Setting the animation
Press
[Animation OFF] Select various patterns
Hint: When setting the watch, you may skip each stage by
pressing B. This way you can easily skip though to the part you
want to change & then skip to the end.

4. How to set the date
Note: after 7 seconds of inactivity setting mode will deactivate.
While the date is displayed, press & hold button B.
The year digits will begin flashing & the SET & Date
icons will be lit.
•
•
The month digits will be flashing.
Press button A to increase the month. (1-12)
Press button B to accept.
The year will be flashing.
Press button A to increase the year.
(hold A to increase quickly)
Press button B to accept.
•
•
•
•
•
•
II. Setting the month
I. Setting the year
Year flashing
Date icon
SET icon
Month flashing

5. How to set the alarm
Note: after 7 seconds of inactivity setting mode will deactivate.
While the alarm is displayed, press & hold button B.
The SET & Alarm icons will be lit.
•
•
Press button A to turn the
alarm ON or OFF
The AL ON icon will be lit to
indicate ON.
Press button B to accept.
The day digits will be flashing.
Press button A to increase the day. (1-31)
(hold A to increase quickly)
Press button B to accept & finish.
•
•
•
•
•
•
I. Turn the alarm ON/OFF
III. Setting the day
Day flashing
Alarm icon
Alarm
ON
icon
SET icon

The hour digits will be flashing.
Press button A to increase the hour.
Press button B to accept.
The minute digits will be flashing.
Press button A to increase the minutes.
(hold A to increase quickly)
Press button B to accept & finish.
•
•
•
•
•
•
II. Setting the alarm hour
III. Setting the alarm minutes
Alarm icon Alarm ON icon
SET icon
Minutes flashing
Alarm icon Alarm ON icon
SET icon
Hour flashing

6. Charging the watch
To recharge the battery, connect the USB charging cable
provided to the watch USB port and then to a power source,
e.g. your computer.
To open the watch USB port, use the screw driver included.
When charging, the charging indicator
will flash.
When the charging indicator stops
flashing, the watch is 90% charged.
It is advised that you continue to charge the watch for a full 3.5
hours to ensure the battery is 100% charged.
Included in the box
• Watch
• USB cable
• Screw driver
• Spare USB cap
• Watch manual
• Link USB cable
•
•
•
•
•
USB charging port screw
Charging
(lights flashing)

7. User information
This watch is covered by a 1 year warranty. This warranty
does not cover water damage, accidental damage, neglect
or unauthorized repair.
II. Warranty
Sequence uses a PL301517 rechargable watch battery.
The battery should last about 2 months between charges.
The battery lifetime is expected to be 300 charges.
Only use the cable provided with the watch for
recharging, as it is designed specifically for this watch.
I. Battery
III. Caution
•
•
•
•
•
•This watch has limited resistance to water. Please do not
use the watch in the shower, for swimming or for other
water related activities.

Case Materials
Case Dimensions
Maximum Fit
Wrist Size
Display
Strap Materials
Finish
Weight
Battery
Wood
Wood
29mm x 52mm x 14mm
210 mm (approx.)
LED Digital Tube
Clear coating
68g
PL301517
SPECIFICATIONS