Tool Shed TSVE8 User manual

PEDESTAL FAN 750MM
TSVE8
www.thetoolshed.co.nz

2
OPERATION MANUAL
www.thetoolshed.co.nz
PRODUCT DETAILS
PRODUCT
MODEL NO.
Pedestal Fan 750mm
TSVE8
D
ISTRIBUTED BY
NOTE:
This manual is only for your reference. Due to the continuous improvement of the ToolShed
products, changes may be made at any time without obligation or notice.
WARRANTY
This product may be covered under the ToolShed warranty. For more information see our Terms
& Conditions at www.thetoolshed.co.nz

3
OPERATION MANUAL
www.thetoolshed.co.nz
C O N T E N T S:
Product Details ....................................................................................................................................... 2
Specifications .......................................................................................................................................... 4
Safety Warnings ..................................................................................................................................... 4
Assembly Instructions ............................................................................................................................ 5
Use / Maintenance ................................................................................................................................. 6

4
OPERATION MANUAL
www.thetoolshed.co.nz
SPECIFICATIONS
Drive Type / Application Direct-Drive – Pedestal
Airflow 290m3 / Min Max
Speeds 3
Blade Diameter 750mm
Blade Type Cast Alloy
Power (Volt/Hz/Watts) 230V / 50Hz / 280W
WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure to follow
instructions and warnings could lead to serious injury, electric shock, or fire. Save ALL warnings
and instructions for future reference.
ELECTRICAL SAFETY
- Do NOT use the power tool in raining conditions or wet areas where to power tool could
get wet. Water in the power tool can lead to electric shock.
- Only use the power tool when the plug correctly matches the power outlet. Modifying
plugs greatly increases the risk of electric shock.
- Keep the power cord away from anything that could damage it such as sharp edges,
moving parts or heat. A damaged power cord increases the risk of electric shock.
- Only operate outdoors with the use of an outdoor extension lead. Not all extension leads
are suited to outdoor use and using one which is not can greatly increase the risk of electric
shock.
SPECIFIC SAFETY INSTRUCTIONS
- DO NOT use the fan outdoors
- NEVER use the fan unless it is fully assembled
- DO NOT push finger or any object through the grilles and do not touch the fan blade during
use. Be extra cautious when children and infants are around during use.
- Take care that objects are not sucked into the fan during operation.
- Unplug from wall outlet before servicing.

5
OPERATION MANUAL
www.thetoolshed.co.nz
ASSEMBLY INSTRUCTIONS
BASE ASSEMBLY
1. Locate Hardware Bag “A” to assemble base. (Figure 1)
2. Fit the column on the
centre of base.
3. Insert (4) M6X12mm hex
bolts through the flange
of the column and base.
4. Tilt base and secure one
hex bolt at a time by first
putting on a split-lock
washer and washer then
nut (M6).
DO NOT FULLY TIGHTEN AT THIS
TIME.
Repeat above procedure with remaining bolts.
5. Go back and fully tighten each nut so that
the flange of the column is securely
assembled to the base.
DECORATION COVER ASSEMBLY
Locate the decoration cover to assemble into the
column. (Figure 2)
1. Loosen the screw which is pointed at by the
arrow and take off the neck.
2. Put the decoration cover into the column.
3. Tighten up the screw.
4. Turn the knob and the height of the inner
column can be adjusted accordingly.
MOTOR ASSEMBLY
Locate the whole set for the motor to assemble into
the column. (Figure 3)
1. The tongue on the connection can match the
groove on the inner column for easy
assembly.
2. Insert the connection into the top of the
inner column.
3. Tighten up two screws on the back (Figure 4)
REAR GRILL ASSEMBLY
Unscrew these 4 screws on the motor, and then
assemble the rear grill.

6
OPERATION MANUAL
www.thetoolshed.co.nz
FAN BLADE ASSEMBLY
1. Insert the fan blade on the shaft of the motor
and let the lateral screw face the flat surface
on the shaft.
2. Fully tighten up the lateral screw of the fan
blade. Be careful, the fan blade should be
assembled in the correct direction. (Figure 7)
FRONT GRILL ASSEMBLY
1. Assemble the font grill in the grill ring and then
fit with the matched rear grill.
2. Close all the locks on the front grill to finish the
assembly. (Figure 9)
USE AND MAINTENANCE
1. Before cleaning, ensure the fan is unplugged and the fan blades have stopped spinning.
2. Disassemble the grill and wash with a soft cloth and soapy water.
3. DO NOT get water in or around the motor.