Toparm EL-208 User manual
Curtainlensdetection view
1 m
1 m
8 m
0.8 m
Note:Check detectoreveryhalfayearatleastforsecurity.
LED
ON/OFF JUMPER
LED ON
LED OFF
Wide anglelensdetection view
WslkTest:AWalkTestenablesyou todetermine the effectiveness
ofthe installation.
1.Warm-up time:80 secondsisrequired afterpowerup.
Features:
Working Mode:passiveinfrared
DigitalSignalProcessing:Advanced passivesignalprocessingtechnologymakeitdetecting
Accuratelysoitcan reducefalsealarm.
PyroelectricSensor:DualElement.
TemperatureCompensation:Thermistor.
InputVoltage:9V-16V/DC,12mA
Alarmoutput:N.C,FormArelay,30VDC/150mAMax.
Tamperoutput:N.C,rated at24VAC/500mAMax.
Alarmoutput(selectable):N.Ocontacts,rated at1A/50V,Max.
*
1
Anti-sunlight:12,000Lux
Anti-frquencydisturbance:48V/m,10MHz-1000MHz
Operating Temperature:Temperature:-10 ~+50 (25 ~113 );Humidity:5~95%.
PassiveInfrared detection lens:Highprecision parabolafocusing curtainstylereflecting mirrors.
Wide anglelensmode:Seven curtains.
*
2
Detection Range:Wide anglelens:12mx10m.Curtainlens:8mx0.8m
*
2
Detection Sensitivity:Curtainmode:Walking across ataspeed of0.3-1.5m/s.
Wide anglemode:Normalwalktwotofourstepswithindetection coverage.
*
2
Dimension:92 x52 x33mm(LXWXH).
Weight:G.W:90g;N.W:70g.
Note:The
*
1
,
*
2
isOptiond accessories.
Mounting location
1,selectamounting location inwhichthe likelydirection ofintrudermotion
4
1
℃℃°F°F
Installtion and operation Manual
EL-208 PassiveInfrared Motion Sensor
LEDIndication
Red LEDlight,alarmoutput, relayworks atabout5seconds.detection
signalsan alarm
2.Curtaindetecting mode walkacross the curtainarea,detectorwill alarmand red LEDlightison.
3.Wide anglemode:Walk2-4stepsfreelyinthe protection area,detectorwill triggeran alarmand Red LED
ison.
TOPView
TOPView
isacross the coverage patterndoor.windowsect
2.Donotinstall inwhichrapidtemperaturechangesfromcentral
heating fromcentralheating,radiators,ducts,airconditioning ect.
3,Makesurethereno obstructionsthatcan blockthe patternofcoverage
L
W
H
0 m
5 m
5 m
2.5 m
2.5 m
12 m
3
6.Remounting covers,and lockit.
3.Pushoutthe frontcoverfrombackcover.
5.Placefrontcoverintothe mounting holeof
backcover.
Installation structions
2
SelectWide lensmode
1.Unlocktheswitch.
2.Prizeup the jointline bet-
ween frontand back cover
withablade screwdriver.
4.1preventreflectorfromdustofdrilling hole,
pleaseremovereflectorwhenmounting back
cover,avoidyourhandscontactingreflector’s
surfacewhenremovingormountingreflector,
onlyblowoff themorwipe off themslightly
withsoft clothafterfounding dustnotother
thingsforkeeping betterdetection effect.
4.2connectthe wirestoterminal,observe
connection polarity
4.3Don’tletyourhandscontactinfrared
sensor.
L
TIMER
EL-208 can useinCurtainlens
detection mode,butascurtainlens
mode,mustchange singlewide
lensintocurtainlensanglelens.
Removing the curtainreflector,pleaseholdreflector’stop .pull emissivemirror
outwards.
When uninstalling,holdon theuppertwosidesofthe mirror,pull the mirrorout,following phaseofright
figureinoppositedirection.Installation:pushcurtainreflecting mirrordownintobottomrind.Pleaserefer
torightfigure.Notice:makesurethe position ofbottomofthe
curtainreflecting mirrormustabsolutelyfitintothe bottomrind.
Pleaserefertopartofthe figure.Horizontallypushcurtainreflect-
ing mirrorintothe detector.Pleaserefertorightfigure
Notice:afterinstallation,makesurethe curtainreflecting mirror
isstable,don’ttouchthe mirrorwhen installing.
Installation
Note:Onlyapplypowerafterall connectionsaremade and inspected.And makesurethe power
polarityiscorrect14-22AWGwireisrecommended.
Note:Donotleavetoo long wireinthe detector.
TerminalsV+&V-: Powerinput, Voltage:9-16V.The max
distanceisupto250m/750feetbetweenthedetectorandpower
sourceifusing wire#22AWG.
TerminalsC&NC:Alarmoutput. 30VDC/150mA.Max
TerminalsT1&T2:Tamperoutput, N.C,24VAC/500mA.
12V/DC
Zoom
Input
ControlPanel
V+
V-
C
NC
T1
T2
Terminals
EOS
Resistor
GND
30cm
60cm
80cm
8M
>1M
Note:pleaseinstall the
detectoron wall,the
placeshouldbe one
meterorhigher.
Ｆｏｒ ｃｕｒｔａｉｎ ｌｅｎｓ Ｆｏｒ ＰａｔｉｏＦｏｒ ｗｉｄｅ ｌｅｎｓ
