Champion Power Equipment 92050-1 User manual

OWNER’S MANUAL
20 Ton
LOG SPLITTER
12039 Smith Ave.
Santa Fe Springs CA 90670
USA / 1-877-338-0999
www.championpowerequipment.com
SAVE THESE INSTRUCTIONS
Important safety instructions
are included in this manual.
MADE IN CHINA
REV 92050-1-20170520
92050-1
MODEL NUMBER

Have questions or need assistance?
Do not return this product to the store!
WE ARE HERE TO HELP!
Visit our website:
www.championpowerequipment.com
for more info:
• Product Info & Updates
• Frequently Asked Questions
• Tech Bulletins
• Product Registration
– or –
Call our Customer Care Team Toll-Free at:
1-877-338-0999
*We are always working to improve our products. Therefore, the enclosed product may differ slightly from the image on the cover.
AN IMPORTANT MESSAGE ABOUT TEMPERATURE:
Your Champion Power Equipment product is designed and rated for continuous operation at ambient temperatures up to
40°C (104°F). When your product is needed your product may be operated at temperatures ranging from -15°C (5°F) to
50°C (122°F) for short periods. If the product is exposed to temperatures outside this range during storage, it should be
brought back within this range before operation. In any event, the product must always be operated outdoors, in a
well-ventilated area and away from doors, windows and other vents.
Parts Ordering:
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338- 0999

92050-1
TABLE OF CONTENTS
Introduction ............................ 1
Manual Conventions. ...................... 2
Safety Rules . ........................... 3
Training ............................. 5
Preparation .......................... 5
Operation. ........................... 6
Maintenance and Storage ................. 6
Controls and Features ..................... 7
Log Splitter .......................... 7
Assembly .............................. 8
Open Shipping Crate .................... 8
1) Install the Tow Bar ................... 8
2) Install the Fenders ................... 8
3) Install the Wheels .................... 8
4) Install the Beam ..................... 8
5) Install the Cylinder and Wedge ........... 9
6) Install the Engine and Hoses ........... 10
7) Install the Log Catchers ............... 10
Add Engine Oil ....................... 11
Add Engine Fuel ...................... 12
Add Hydraulic Oil ..................... 12
Operation . ............................ 13
Before Each Use Inspect the Log Splitter ..... 13
Towing Log Splitter Safety ............... 13
Log Splitter Location ................... 13
Starting the Engine .................... 14
Stopping the Engine ................... 14
Log Splitter Operation .................. 15
Operation at High Altitude ............... 15
Maintenance and Storage .................. 16
Engine Maintenance ................... 16
Oil ............................. 16
Spark Plugs ....................... 16
Air Filter ......................... 16
Cleaning ......................... 16
Maintenance Schedule. ............... 17
Log Splitter Maintenance ................ 17
Storage ............................ 17
Log Splitter Storage ................. 17
Engine stored for Less than 30 Days ...... 17
Engines Stored for Over 30 Days. ........ 17
Specifications . ......................... 18
Log Splitter Specifications ............... 18
Engine Specifications .................. 18
Fuel .............................. 18
Oil ............................... 18
Hydraulic Oil ........................ 18
Spark Plugs ......................... 18
Maintenance Valve Clearance ............. 18
Parts Diagram. ....................... 19
Parts List . .......................... 20
Engine Parts Diagram .................. 21
Engine Parts List ..................... 22
Troubleshooting. ........................ 23
20 Ton
LOG SPLITTER

1
ENGLISH 92050-1
INTRODUCTION
Record the model and serial numbers as well as date and place of purchase for future reference. Have this
information available when ordering parts and when making technical or warranty inquiries.
Champion Power Equipment Support
Model Number
Serial Number
Date of Purchase
Purchase Location
1-877-338-0999
92050-1
For Oil Type see ‘Add Engine Oil‘ section. For Fuel Type see ‘Add Fuel‘ section.
Congratulations on your purchase of a Champion Power Equipment product. Champion Power Equipment and
Champion Engine Technology designs, builds, and supports all of our products to strict specifications and guidelines.
With proper product knowledge, safe use, and regular maintenance, this product should bring years of satisfying
service.
Every effort has been made to ensure the accuracy and completeness of the information in this manual, and we
reserve the right to change, alter and/or improve the product and this document at any time without prior notice.
Since CPE/CET highly value how our products are designed, manufactured, operated and are serviced, and also
highly value your safety and the safety of others, we would like you to take the time to review this product manual
and other product materials thoroughly and be fully aware and knowledgeable of the assembly, operation, dangers
and maintenance of the product before use. Fully familiarize yourself, and make sure others who plan on operating
the product fully familiarize themselves too, with the proper safety and operation procedures before each use. Please
always exercise common sense and always error on the side of caution when operating the product to ensure no
accidents, property damage, or injury occurs. We want you to continue to use and be satisfied with your CPE/CET
product for years to come.

2
92050-1 ENGLISH
MANUAL CONVENTIONS
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
CAUTION
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, may result in property damage.
CAUTION
This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol
is used with a key word to alert you to potential hazards in operating and owning power equipment.
Follow all safety messages to avoid or reduce the risk of serious injury or death.
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
DANGER
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
WARNING
If you have questions regarding your log splitter, we can
help. Please call our help line at 1-877- 338-0 999
NOTE

3
ENGLISH 92050-1
SAFETY RULES
Log Splitter engine exhaust contains carbon
monoxide, a colourless. odourless, poison gas.
Breathing carbon monoxide will cause nausea,
dizziness, fainting or death. If you start to feel dizzy
or weak, get to fresh air immediately.
DANGER
Operate log splitter outdoors only in a well
ventilated area. DO NOT operate the log splitter
inside any building, enclosure or compartment.
DO NOT allow exhaust fumes to enter a confined
area through windows, doors, vents or other
openings. DANGER CARBON MONOXIDE, using a
log splitter indoors CAN KILL YOU IN MINUTES.
Rotating parts can entangle hands, feet, hair,
clothing and/or accessories. Traumatic amputation or
severe laceration can result.
DANGER
Keep hands and feet away from rotating parts. Tie up
long hair and remove jewellery. Operate equipment
with guards in place. DO NOT wear loose-fitting
clothing, dangling drawstrings or items that could
become caught.
Read this manual thoroughly before operating your
log splitter. Failure to follow instructions could result
in serious injury or death.
WARNING
Before removing the pin installed into the front
support leg make sure hitch is installed onto vehicle.
Releasing the pin before will cause support leg to
slide up and possibly cause injury.
WARNING
Sparks can result in fire or electrical shock.
DANGER
When servicing the engine:
Disconnect the spark plug wire and place it where
it cannot contact the plug. DO NOT check for spark
with the plug removed. Use only approved spark
plug testers.
Running engines produce heat. Severe burns can
occur on contact. Combustible material can catch
fire on contact.
DO NOT touch hot surfaces. Avoid contact with
hot exhaust gases. Allow equipment to cool before
touching. Maintain at least 91.4 cm (3 ft.) of
clearance on all sides to ensure adequate cooling.
Maintain at least 1.5 m (5 ft.) of clearance from
combustible materials.
WARNING
Crush hazard
Wedge can cut through skin and break bones. Keep
all limbs away from wedge and endplate.
WARNING
Projectile hazard
Pieces of log may be ejected from the splitter while
operating. Wear ANSI approved safety glasses when
operating. Be alert.
WARNING
Keep operator work zone clear
Keep work zone clear of debris while working to
ensure safe footing.
WARNING

4
92050-1 ENGLISH
Fuel and fuel vapours are highly flammable and
extremely explosive.
Fire or explosion can cause severe burns or death.
Unintentional startup can result in entanglement,
traumatic amputation or laceration.
When adding or removing fuel:
Turn the engine off and let it cool for at least two
minutes before removing the fuel cap. Loosen the
cap slowly to relieve pressure in the tank.
Only fill or drain fuel outdoors in a well-ventilated area.
DO NOT pump gas directly into the log splitter
at the gas station. Use an approved container to
transfer the fuel to the log splitter.
DO NOT overfill the fuel tank.
Always keep fuel away from sparks, open flames,
pilot lights, heat and other sources of ignition.
DO NOT light or smoke cigarettes.
When starting the engine:
DO NOT attempt to start a damaged engine.
Make certain that the gas cap, air filter, spark plug,
fuel lines and exhaust system are properly in place.
Allow spilled fuel to evaporate fully before
attempting to start the engine.
Make certain that the log splitter is resting firmly on
level ground.
When operating the log splitter:
DO NOT move or tip the log splitter during
operation.
DO NOT tip the log splitter or allow fuel or oil to
spill.
Block the tires to prevent unintended movement.
When transporting or servicing the log splitter:
Make certain that the fuel shutoff valve is in the off
position and the fuel tank is empty.
Disconnect the spark plug wire.
When storing the log splitter:
Store away from sparks, open flames, pilot lights,
heat and other sources of ignition.
DANGER
SAFETY RULES
Skin injection hazard. High-pressure hydraulic oil
can inject under your skin.
DANGER
Make sure all fittings are tightly secure before
applying pressure. Relieve system of pressure
before servicing.
Towing hazard
ALWAYS check all local and state regulations
regarding towing, licensing and lights before towing
your log splitter. Review towing safety warnings in
your towing vehicle manual.
Drive safely. Be aware of the added length of the
log splitter. NEVER ride or transport cargo on the
log splitter. Choose a level surface to operate the
log splitter.
NEVER EXCEED MAX. Towing Speed
72 km/h (45 MPH)
WARNING
Rapid retraction of the starter cord will pull hand and
arm towards the engine faster than you can let go.
Unintentional startup can result in entanglement,
traumatic amputation or laceration.
Broken bones, fractures, bruises or sprains could
result.
When starting engine, pull the starter cord slowly
until resistance is felt and then pull rapidly to avoid
kickback.
WARNING
Improper treatment or use of the log splitter can
damage it, shorten its life and void your warranty.
Use the log splitter only for intended uses. Operate
only on level surfaces. DO NOT expose log splitter
to excessive moisture, dust, or dirt.
DO NOT allow any material to block the cooling
slots. DO NOT use the engine if:
– Equipment sparks, smokes or emits flames
– Equipment vibrates excessively
CAUTION
Parts of the hydraulic circuit (cylinder, pump, valve-
body, hoses) can become very hot during operation.
CAUTION

5
ENGLISH 92050-1
SAFETY RULES
Training
1. Read the Operator’s Manual completely before
attempting to use this log splitter.
2. Do not allow anyone to operate your log splitter who
has not read the Operator’s Manual or has not been
instructed on the safe use of the log splitter.
3. Never allow children or untrained adults to operate
this machine.
4. Many accidents occur when more than one (1) person
operates the log splitter. If a helper is assisting in
loading logs to be split, never actuate controls until
helper is clear of the area.
5. Never allow anyone to ride on the machine.
6. Never transport cargo on the log splitter.
7. High fluid pressures are developed in hydraulic
log splitters. Pressurized hydraulic fluid escaping
through a pin hole opening can puncture skin and
cause sever blood poisoning. Therefore, the following
instructions should be heeded at all times.
a. Do not operate the unit with frayed, kinked,
cracked or damaged hoses, fittings, or tubing.
b. Stop the engine and relieve hydraulic system
pressure before changing or adjusting fittings,
hoses, tubing, or other system components.
c. Do not adjust the pressure settings of the pump
or valve.
d. Do not check for leaks with your hand. Leaks
can be detected by passing cardboard or wood
over the suspected area. Look for discolouration.
If injured by escaping fluid, see a doctor at
once. Serious infection or reaction can develop
if proper medical treatment is not administered
immediately.
8. Keep the operator zone and adjacent area clear for
safe, secure footing.
9. If your log splitter is equipped with an internal-
combustion engine and intended for use near any
unimproved forest, brush, or grass covered land,
the engine exhaust should be equipped with a spark
arrestor. Make sure you comply with local, state,
and federal codes. Take appropriate fire-fighting
equipment with you.
10.Log splitters should be used only for splitting
wood. Do not use for other purposes unless the
manufacturer provides attachments and instructions.
Preparation
1. Be thoroughly familiar with all controls and with
proper use of the equipment.
2. Safety Gear:
a. Always wear safety shoes or heavy boots when
operating the machine.
b. Always wear safety glasses or goggles when
operating the machine.
c. Never wear jewelry or loose-fitting clothing that
might become entangled in moving or rotating
parts of the machine.
3. Make sure the splitter is on a level surface. Block
tires and ensure support leg is secure to prevent
unintended movement of the log splitter during
operation.
a. Always operate the splitter from the
manufacturer’s indicated operator zone.
4. Logs to be split on ram-type units should be cut as
squarely as possible.
5. Fuel:
a. Use an approved fuel container.
b. Never add fuel to a running or hot engine.
c. Fill fuel tank outdoors with extreme care. Never
fill fuel tank indoors.
d. Replace gasoline cap securely and clean up any
spilled fuel.

6
92050-1 ENGLISH
SAFETY RULES
Maintenance and Storage
1. Always shut off the power source while repairing or
adjusting the splitter except as recommended by the
manufacturer.
2. Clean debris and chaff from the engine cylinder,
cylinder head fins, blower house rotation screen,
and muffler areas. If the engine is equipped with a
spark arrestor muffler, clean and inspect it regularly
(follow manufacturer’s service instructions). Replace,
if damaged.
3. Never store the unit indoors with fuel in the tank.
Fumes might reach an open flame spark. Allow the
engine to cool before storing in any enclosure.
4. Clear debris from moveable parts, but only when the
power source is shut off.
5. Check to be sure all nuts and bolts are tight to
assure the equipment is in safe working condition.
Operation
1. Before starting this log splitter, review all safety
rules. Failure to follow these rules may result in
serious injury to the operator or bystanders.
2. Be sure to confirm all hose connections and hose
clamps are tight before each use. It is possible for
connections to vibrate loose over time.
3. Never leave the machine unattended with the power
source operating.
4. Never operate the machine when under the influence
of alcohol, drugs or medication.
5. The machine owner should instruct all operators in
safe log splitter operation.
6. Always operate the log splitter with all safety
equipment in place and all controls properly adjusted
for safe operation.
7. Always operate the log splitter at manufacturer’s
recommended speed.
8. Always keep hands and feet clear of moving parts.
9. When loading a ram-type log splitter, place your
hands on the sides of the log, not the ends. Never
place your hands or any part of your body between a
log and any part of the log splitter.
a. On ram-type log splitters, never attempt to split
more than one (1) log at a time unless the ram
has been fully extended and a second log is
needed to complete the separation of the first log.
10.On ram-type log splitters on which the logs are not
cut square, the longest portion of the log should
be rotated down and the most square end placed
against the ram.
11. Use only your hand to operate the log splitter controls.
12.Do not refuel the engine until it has cooled for several
minutes.

7
ENGLISH 92050-1
(1) 5.1 cm (2 in.) Ball Coupler – For towing the log
splitter behind your vehicle.
(2) Hydraulic Cylinder – Bore 10 cm (3.9 in.) x
57.5 cm (22.6 in.) stroke. Rated to 3600 psi.
(3) Engine – 196cc, OHV, 4-stroke, air cooled.
(4) Control Valve Handle – Controls the movement of
the cutting wedge.
(5) Wedge
(6) Splitting Beam
(7) Log Catchers
(8) Fenders
(9) Tires – Maximum travel speed is 72 km/h
(45 MPH).
(10) Mounting Plates – Holds hydraulic cylinder in
place.
(11) Support Leg – Supports log splitter while
operating. Raise leg for towing.
(12) Safety Chains – For use while towing.
Log Splitter
CONTROLS AND FEATURES
Read this owner’s manual before operating your log splitter. Familiarize yourself with the location and function of the
controls and features. Save this manual for future reference.
1
32
911
10
8
6
7
4
5
12

8
92050-1 ENGLISH
ASSEMBLY
A
Your log splitter is requires some assembly.
If you have any questions regarding the assembly of your
log splitter, call our help line at 1-877-338-0999. Please
have your serial number and model number available.
Open Shipping Crate
1. Set the shipping crate on a solid, flat surface
2. Carefully cut the shipping bands and remove lid of
shipping crate.
3. Locate all hardware before beginning assembly.
1) Install the Tow Bar
1. Assemble two piece tow bar with two M12x65 bolts
and M12 lock nuts and washers. (A)
2. Attach the tow bar to the bracket on top of the hydraulic
oil tank with two M12x85 bolts and M12 lock nuts. (B)
3) Install the Wheels
1. Place bearings in the wheel hub
2. Press the seal over the bearing on the inside of the
wheel. Use a hammer and wood block to flush the seal
with the end of the hub.
3. Slide the wheel over the axel on the hydraulic oil tank.
4. Install the castle nut and tighten by hand. Tighten
another ¼turn with a wrench to seat the bearing.
5. Spin the wheel to distribute grease.
6. Loosen the castle nut and re-tighten by hand.
7. Install the cotter pin through the castle nut and axle to
prevent the nut from backing off.
8. Place axle cap over castle nut and axle.
9. Repeat steps 1-8 for the other wheel.
Keep the wheel hub clean and free from debris
during assembly.
NOTE
B
Over-tightening the castle nut will cause the
bearings to run hot and fail prematurely.
CAUTION
2) Install the Fenders
1. Attach the fender to the side of the hydraulic oil tank
with an M10x30 bolt, M10 washer, M10 lock washer
and M10 nut. The safety reflector should be facing the
back of the hydraulic oil tank.
2. Repeat with second fender on opposite side.
A
4) Install the Beam
1. Install the front support leg and secure with pin and
R-pin (hairpin clip). (A)
2. Stand the beam upright on foot plate behind the
hydraulic fluid tank. (B)

9
ENGLISH 92050-1
ASSEMBLY
C
D
A
4) Install the Beam Cont’d. 5) Install the Cylinder and Wedge
1. Place the wedge on the beam between the cylinder
mounts and slide it forward into the rails. (A)
2. Remove the cylinder mounting plates. (A)
3. Install the cylinder by sliding the pegs at the end
of the cylinder into the mounting slots on top of the
beam. Be sure to slide the cylinder all the way back
into the mounting slots. (B)
5. Hold the top of the beam by the cylinder mount and
carefully rotate the beam toward the tow bar.
6. Once the bracket on the bottom of the beam is aligned
with the tow bar, secure with pin and R-pin. (D)
The cylinder will support itself when slid all the way
back into the mounting slots.
NOTE
4. Secure the cylinder mounting plates with hardware
removed in step 2. (B)
5. Slide the wedge back toward the cylinder and align
the bolt hole in the wedge with the bolt hole in the
cylinder rod. (B)
6. Secure the wedge to the cylinder rod with an
M12x75 bolt and M12 nut. Lightly tighten the nut to
approximately 5 ft-lb. (B)
B
The cylinder rod may need to be rotated slightly
in order to properly align the the wedge. Insert a
screwdriver into the bolt hole in the cylinder rod
and slowly rotate as needed.
NOTE
3. Slowly lift the front of the tow bar to roll the frame
toward the beam and carefully align the pivot holes
on the bottom of the beam and the top of the
hydraulic oil tank.
4. Once aligned, secure the beam to the tank with hitch
pin and R-pin. (C)
B
Beam is heavy. Use at least 2 people when lifting or
moving the beam.
CAUTION

10
92050-1 ENGLISH
ASSEMBLY
6) Install the Engine and Hoses Cont’d.
6) Install the Engine and Hoses
1. Attach the engine/pump to the engine mounting plate
on the hydraulic oil tank. (A)
2. Place O-ring into the outlet fitting on the top of the
pump. (A)
3. Connect one end of the high pressure hose to the
pump outlet fitting and the other end to the inlet on
the control valve. (B)
The swivel nut end of the high pressure hose
connects to the pump outlet.
NOTE
4. Connect one end of the clear oil hose to the hydraulic
oil tank just beneath the engine and the other end to
the pump inlet on the bottom of the pump. (C)
C
B
A
D
1. Attach log catcher (1) to side of beam with four
M10x15 bolts (2), four M10 lock washers (3), and
four M10 washers (4).
2. Repeat step 1 for the other side.
7) Install the Log Catchers
Red shipping plugs must be removed from hydraulic
pump prior to installing hoses.
Hydraulic pump may
contain residual oil from
testing procedures during
production. We recommend
using an oil tray under the
pump before removing the
shipping plugs.
CAUTION
5. Connect one end of the oil return hose to the outlet
barb fitting on the control valve and the other end to
the barb fitting on the oil tank. (D)

11
ENGLISH 92050-1
ASSEMBLY
Add Oil Cont’d.
The engine is equipped with a low oil shut-off and will
stop when the oil level in the crankcase falls below the
threshold level.
CAUTION
The recommended oil type is 10W-30 automotive oil.
NOTE
Synthetic oil may be used after the 5 hour initial break-
in period. Using synthetic oil does not increase the
recommended oil change interval.
NOTE
We consider the first 5 hours of run time to be the break-
in period for the unit. During the break in period stay at
or below 50% of the running watt rating and vary the
load occasionally to allow stator windings to heat and
cool. Adjusting the load will also cause engine speed to
vary and help seat piston rings. After the 5 hour break-in
period, change the oil.
NOTE
Once oil has been added, a visual check should show oil
about 1-2 threads from running out of the fill hole.
If using the dipstick to check oil level, DO NOT screw in
the dipstick while checking.
NOTE
Weather will affect engine oil and engine performance.
Change the type of engine oil used based on weather
conditions to suit the engine needs.
NOTE
Add Engine Oil
1. Make sure the log splitter is on a flat, level surface.
2. Remove oil fill cap/dipstick to add oil.
3. Add up to 0.6 L (0.6 qt.) of oil. Replace oil fill cap/
dipstick. DO NOT OVERFILL.
4. Check engine oil level daily and add as needed.
DO NOT attempt to crank or start the engine before it
has been properly filled with the recommended type and
amount of oil. Damage to the log splitter as a result of
failure to follow these instructions will void your warranty.
CAUTION
Full Synthetic 5W-30
Degrees Celsiusº (Outside)
(Outside)
Degrees Fahrenheitº

12
92050-1 ENGLISH
ASSEMBLY
6. Start Engine. Extend and retract the wedge to purge
air from the hydraulic system. When the wedge
motion is smooth, the system is properly purged.
7. Check the hydraulic oil tank sight glass. Add
approximately 1 to 1.5 gallons of hydraulic oil to
bring the level back up to the sight glass.
Our engines work well with 10% or less ethanol blend
fuels. When using blended fuels there are some issues
worth noting:
– Ethanol-gasoline blends can absorb more water than
gasoline alone.
– These blends can eventually separate, leaving water
or a watery goo in the tank, fuel valve and carburetor.
– With gravity-fed fuel supplies, this compromised fuel
can be drawn into the carburetor and cause damage
to the engine and/or potential hazards.
– There are only a few suppliers of fuel stabilizer that
are formulated to work with ethanol blend fuels.
– Any damages or hazards caused by using improper
fuel, improperly stored fuel, and/or improperly
formulated stabilizers, are not covered by
manufacture’s warranty.
It is advisable to always shut off the fuel supply, run the
engine to fuel starvation and drain the tank when the
equipment is not in use for more than 30 days.
NOTE
DO NOT remove the hydraulic oil fill cap when the
engine is running or hot. Hot oil can escape causing
severe burns. Always allow the log splitter to cool
completely before removing the hydraulic oil cap.
High fluid pressure and temperatures are created
in the hydraulic log splitters. Hydraulic fluid will
escape through a pin-size hole opening and can
puncture skin and cause severe blood poisoning.
Inspect hydraulic system regularly for possible
leaks. Never check for leaks with your hand while
the system is pressurized. Seek medical attention
immediately if injured by escaping fluid.
WARNING
Add Hydraulic Oil
1. Make sure the log splitter is on a flat, level surface.
2. Remove the oil plug from the oil tank. (A)
3. Add 15.1 L (4 gal.) of hydraulic oil - 10W AW32, ASLE
H-150, or ISO 32 are all acceptable types of fluid.
4. Check the hydraulic oil level using the oil sight glass.
Oil level should be centered on the glass sight. (B)
5. Replace and tighten the oil plug and orient the vent
hole away from the operator zone.
A
B
Add Engine Fuel
1. Use clean, fresh, regular unleaded fuel with a
minimum octane rating of 85 and an ethanol content
of less than 10% by volume.
2. DO NOT mix oil with fuel.
3. Clean the area around the fuel cap.
4. Remove the fuel cap.
5. Slowly add fuel to the tank. DO NOT OVERFILL. Fuel
can expand after filling. A minimum of 6.4 mm (¼in.)
of space left in the tank is required for fuel expansion,
more than 6.4 mm (¼in.) is recommended. Fuel can
be forced out of the tank as a result of expansion if it is
overfilled, and can affect the stable running condition of
the product. When filling the tank, it is recommended
to leave enough space for the fuel to expand.
6. Screw on the fuel cap and wipe away any spilled fuel.
Use regular unleaded gasoline with a minimum
octane rating of 85.
Do not mix oil and gasoline.
Fill tank to approximately 6.4 mm (¼in.) below the
top of the tank to allow for fuel expansion.
DO NOT pump gas directly into the engine at the
gas station. Use an approved container to transfer
the fuel to the generator.
DO NOT fill fuel tank indoors.
DO NOT fill fuel tank when the engine is running or hot.
DO NOT overfill the fuel tank.
DO NOT light cigarettes or smoke when filling the
fuel tank.
CAUTION
Pouring fuel too fast through the fuel screen may
result in blow back of fuel at the operator while filling.
WARNING
Add Engine Fuel Cont’d.

13
ENGLISH 92050-1
OPERATION
Before Each Use Inspect the Log Splitter
1. Check the hydraulic oil level and visually inspect all
hoses, attachments and cylinder for leaks, cracks,
fraying or other damage.
2. DO NOT operate the log splitter if there is any
indication of damage or oily residue.
3. Inspect the engine and make sure the oil level is
correct before operating. If the engine is equipped
with a spark arrestor, clean and inspect it regularly
(follow spark arrestor maintenance schedule).
4. The tires need to be fully inflated and in good repair.
Reference the tire sidewall for recommended tire
pressure.
Towing Log Splitter Safety
1. Always check local and state regulations regarding the
requirements for towing, licensing and lights.
2. Before towing make sure the log splitter is correctly
and securely attached to the vehicle and the safety
chains attached with enough slack to allow for turning.
3. Never exceed the max. travel speed of 72 km/h (45
MPH). Towing the log splitter at speeds greater than
72 km/h (45 MPH) could result in serious injury or
death. Always adjust your towing speed according to
the terrain and conditions.
4. Always disconnect the log splitter from the towing
vehicle before operating.
Log Splitter Location
This log splitter must have at least 2.1 m (7 ft.) of
clearance from combustible material. Leave at least
91.4 cm (3 ft.) of clearance on all sides of the log splitter
to allow for adequate cooling, maintenance and servicing.
DO NOT place the log splitter near vents or intakes where
engine exhaust fumes could be drawn into occupied or
confined spaces. Always operate the log splitter outdoors.
The log splitter needs to be on a dry, level surface with
good footing. DO NOT work on mud, ice, tall grass, brush
or snow.
Only operate log splitter from work zone shown below.
Vertical Operating
Position
W
o
r
k
Z
o
n
e
Horizontal Operating
Position
W
o
r
k
Z
o
n
e
Log Splitter Location Cont’d.
For Vertical Operation:
– Remove the beam lock-pin from the beam
bracket
– Use handle on cylinder to rotate beam to vertical
position
– Insert beam lock-pin in the pivot bracket
NOTE
DO NOT overinflate tires. Serious injury can result if
tires explode.
DO NOT tow the log splitter if the tires are worn or
will not hold air.
DO NOT exceed the maximum 72 km/h (45 MPH)
towing speed.
WARNING

14
92050-1 ENGLISH
OPERATION
Starting the Engine
1. Make certain the log splitter is on a flat, level surface.
2. Turn engine switch to “ON” position.
3. Turn the fuel valve to the “ON” position.
4. Move the choke lever to the “Choke” position.
5. Pull the starter cord slowly until resistance is felt and
then pull rapidly. SEE NOTE BELOW.
6. As engine warms up, move the choke lever to “Run.”
7. Move the throttle lever to the “Fast” position.
ALWAYS use the log splitter for its intended use. The
log splitter should only be used to split wood logs,
length wise with the grain.
NEVER modify, alter or change the log splitter in
anyway. Modifications will void the warranty.
NEVER attach a rope, cable or other device to the
control lever on the log splitter.
DO NOT modify or change the engine and operating
speeds or pressure settings. These changes can
cause safety issues.
ONLY operate the log splitter in daylight.
NEVER operate, or let anyone else operate, the log
splitter while under the influence of alcohol, drugs,
or medication.
NEVER leave the log splitter unattended while the
engine is running.
DO NOT change the splitting position with the engine
running. Contact with the muffler can cause serious
burns.
Always make sure the beam is in the locked position.
DO NOT let the beam drop as it could crush fingers
or cause damage to the log splitter.
WARNING
Log Splitter Location Cont’d. Starting the Engine Cont’d.
If the engine starts, but does not run, make certain
that the log splitter is on a flat, level surface. The
engine is equipped with a low oil sensor that will
prevent the engine from running when the oil level
falls below a critical threshold.
The hydraulic oil needs to be above -12°C (10°F)
before starting the engine. Cold hydraulic oil can
damage the hydraulic pump.
If outdoor air temperature is below 0°C (32°F)
allow the log splitter to warm up by extending and
returning the wedge several times before splitting
wood.
NOTE
Keep choke lever in “Choke” position for only 1
pull of the recoil starter. After first pull, move choke
lever to the “Run” position for up to the next 3
pulls of the recoil starter. Too much choke leads to
spark plug fouling/engine flooding due to the lack of
incoming air. This will cause the engine not to start.
NOTE
Stopping the Engine
1. Turn the fuel knob to the “Off” position.
2. Let the engine run until fuel starvation has stopped
the engine. This usually takes a few minutes.
3. Turn the engine switch to the “Off” position.
Important: Always ensure that the Fuel Valve and the
Engine Switch are in the “OFF” position when the engine
is not in use.
If the engine will not be used for a period of two (2)
weeks or longer, please see the Storage section for
proper engine and fuel storage.
NOTE

15
ENGLISH 92050-1
OPERATION
HORIZONAL position is used for lighter logs that can
easily be loaded onto the beam.
VERTICAL position is used for light logs as well as
heavy logs that are difficult to load onto the beam.
Back injury can result from lifting logs onto the log
splitter if proper lifting techniques are not used.
NOTE
It is normal for the hydraulic fluid to become foamy
or frothy during operation.
NOTE
Log Splitter Operation
1. ALWAYS wear ear and eye protection, protective clothing
and safety gear.
2. Block tires and put support leg in the DOWN position
to prevent unintended movement of the log splitter
during operation.
3. Set log splitter in either the horizontal or vertical
position.
4. Load a log onto the beam against the end plate (MAX
LOG LENGTH – 60.3 cm {23.8 in.}).
5. Make sure all limbs are clear of crush zones.
6. Push the control valve handle forward (towards the
end plate) to split the log.
7. Push the auto control valve handle backward to
return the wedge to its original position.
8. Clear the split wood from the work zone.
Do not hold auto control valve in return position. It
will damage the stop block or beam.
CAUTION
Operation at High Altitude
The density of air at high altitude is lower than at sea
level. Engine power is reduced as the air mass and
air-fuel ratio decrease. Engine power and output will
be reduced approximately 3½% for every 1000 feet of
elevation above sea level. This is a natural trend and
cannot be changed by adjusting the engine. At high
altitudes increased exhaust emissions can also result
due to the increased enrichment of the air fuel ratio.
Other high altitude issues can include hard starting,
increased fuel consumption and spark plug fouling.
To alleviate high altitude issues other than the natural
power loss, Champion Power Equipment can provide a
high altitude carburetor main jet. The alternative main
jet and installation instructions can be obtained by
contacting Customer Support. Installation instructions
are also available in the Technical Bulletin area of the
Champion Power Equipment internet site.
The part number and recommended minimum altitude
for the application of the high altitude carburetor main
jet is listed in the table below.
In order to select the correct high altitude main jet
it is necessary to identify the carburetor model. For
this purpose, a code is stamped on the side of the
carburetor. Select the correct main jet part number
corresponding to the carburetor code found on your
particular carburetor.
Operation using the alternative main jet at
elevations lower than the recommended minimum
altitude can damage the engine. For operation at
lower elevations, the standard main jet must be
used. Operating the engine with the wrong engine
configuration at a given altitude may increase
its emissions and decrease fuel efficiency and
performance.
WARNING
Carburetor
Code Main Jet Part Number Altitude
P19-1-Z
Standard 26.131017.00.Z
3500 Feet
(1067 Meters)
Altitude 26.131017.00.01.Z
P19-1-H
Standard 26.131017.00.H
Altitude 26.131017.00.01.H
P19-1-Y
Standard 26.131017.00.Y
Altitude 26.131017.00.01.Y

16
92050-1 ENGLISH
MAINTENANCE AND STORAGE
The owner/operator is responsible for all periodic
maintenance.
Complete all scheduled maintenance in a timely manner.
Correct any issue before operating the log splitter.
For service or parts assistance, contact our help line
at 1-877-338-0 999.
NOTE
Never operate a damaged or defective log splitter.
WARNING
Improper maintenance will void your warranty.
WARNING
Used oil is a hazardous waste product and must be
disposed of properly. Do not discard with household
waste. Check with your local authorities, service center, or
dealer for safe disposal/recycling facilities.
WARNING
Engine Maintenance
To prevent accidental starting, remove and ground spark
plug wire before performing any service.
Oil
Change oil when the engine is warm. Refer to the oil
specification to select the proper grade of oil for your
operating environment.
1. Remove the oil drain plug with a 12 mm socket and extension.
2. Allow the oil to drain completely.
3. Replace the drain plug.
4. Remove oil fill cap/dipstick to add oil.
5. Add up to 0.6 L (0.6 qt.) of oil and replace oil fill cap/
dipstick. DO NOT OVERFILL.
6. Dispose of used oil at an approved waste management facility.
DO NOT use a garden hose to clean the engine or
log splitter.
CAUTION
Water can contaminate the fuel system and can
enter the engine through the cooling slots and
damage the engine.
Cleaning
Clear the debris from the beam, wedge and endplate. Use
a damp cloth to clean exterior surfaces of the engine and
log splitter.
Use a soft bristle brush to remove excess dirt and oil. Use
an air compressor (25 PSI) to clear dirt and small debris.
Wipe all metal parts with an oily rag to help prevent rust
and corrosion.
Spark Plugs
1. Remove the spark plug cable from the spark plug.
2. Inspect the electrode on the plug. It must be clean
and not worn to produce the spark required for
ignition.
3. Make certain the spark plug gap is 0.7 - 0.8 mm
(0.028 - 0.031 in.).
4. Refer to the spark plug recommendation chart when
replacing the plug.
5. Carefully thread the plug into the engine.
6. Use the spark plug tool to firmly install the plug.
7. Attach the spark plug wire to the plug.
Once oil has been added, use the dipstick to check oil
level, DO NOT screw in the dipstick while checking.
NOTE
0.7-0.8 mm
0.028-0.031 in.
Air Filter
1. Unscrew wing nuts to remove the air filter cover.
2. Remove the foam element.
3. Wash in liquid detergent and water. Squeeze
thoroughly dry in a clean cloth.
4. Saturate in clean engine oil.
5. Squeeze in a clean, absorbent cloth to remove all
excess oil.
6. Place the filter in the assembly.
7. Reattach the air filter cover and using your fingers,
tighten wing nuts. Screw until tight. Be sure not to
over tighten.

17
ENGLISH 92050-1
MAINTENANCE AND STORAGE
Maintenance Schedule
Follow the service intervals indicated in the schedule
below. Service your log splitter more frequently when
operating in adverse conditions. Contact our help line at
1-877-33 8-09 99 to locate the nearest Champion Power
Equipment authorized service dealer for your log splitter
or engine maintenance needs.
Log Splitter Maintenance
Make certain that the log splitter is kept clean and stored
properly. Only operate the unit on a flat, level surface in
a clean, dry operating environment. DO NOT expose the
unit to extreme conditions, excessive dust, dirt, moisture
or corrosive vapours.
Inspect all air vents and cooling slots to ensure that they
are clean and unobstructed.
Clean spark arrester every 100 hours.
Check and tighten all bolts and nuts before operating the
log splitter.
*To be performed by knowledgeable, experienced owners, any small
engine repair shop, or Champion Power Equipment certified dealers.
Never store the log splitter inside next to appliances where
there is a source of heat or open flame, spark or pilot light
because they can ignite gasoline vapors.
DO NOT store a log splitter near fertilizer or any corrosive
material.
Even with an empty gas tank, gasoline vapors could ignite.
WARNING
Storage
Refer to the Maintenance section for proper cleaning
instructions.
Log Splitter Storage
1. The log splitter needs to be cool for at least 5
minutes before storing.
2. Clean the log splitter before storage according to the
Maintenance section.
3. Retract the wedge to protect the rod from corrosion.
4. Wipe the beam and wedge with an oily rag to prevent
rust and corrosion.
Engine Stored for Less than 30 Days
1. Allow the engine to cool completely before storage.
2. Clean engine according to the Maintenance section.
3. To extend the fuel storage life add a properly
formulated fuel stabilizer to the tank.
4. Ensure the fuel valve is in the “OFF” position.
Engines Stored for Over 30 Days
1. Add a properly formulated fuel stabilizer to the tank.
2. Run the engine for a few minutes so the treated fuel
cycles through the fuel system and carburetor.
3. Turn the fuel valve to the “Off” position.
4. Let the engine run until fuel starvation has stopped
the engine. This usually takes a few minutes.
5. The engine needs to cool completely before cleaning
and storage.
6. Clean the engine according to the maintenance section.
7. Change the oil.
8. Remove the spark plug and pour about 1⁄2 ounce
(14.8 mL) of oil into the cylinder. Using the Recoil,
crank the engine slowly to distribute the oil and
lubricate the cylinder.
9. Reattach the spark plug.
Every 8 hours or daily
Check engine and hydraulic oil levels
Clean around air intake and muffler
First 5 Hours
Change engine oil
Every 50 hours or every season
Clean air filter
Change engine oil if operating under heavy load or in
hot environments
Every 100 hours or every season
Change engine oil
Clean/Adjust spark plug
Check/Adjust valve clearance*
Clean fuel tank and filter*
Change hydraulic oil
Change hydraulic oil filter
Every year
Inspect wheel bearings and repack bearing grease as
needed
Every 3 years
Replace fuel line