Torklift C2213 Service manual

1
IMPORTANT OWNER-OPERATOR INSTALLATION INSTRUCTIONS
C2213 / C2220
REVISED vers7 BY: JL 8/5/2015
TECH SUPPORT [phone]
AFTER INSTALL, PLEASE GIVE
THIS BOOKLET TO YOUR CUSTOMER

2
Warnings
Truck Bed and Camper Protection
Torklift does not recommend installing your camper on top of a plastic bed liner (or other
compressible material such as foam). These materials can act as a spring, causing increased
vertical truck camper movement independent of the vehicle. Plastic bed liners can slide on the
truck bed surface, and the truck camper can slide on top of the bed liner. Using a plastic bed
liner or similar compressible material will void your warranty and may additionally cause truck
bed and/or camper damage.
Minor movement or settling can occur in some incidental harsh driving conditions (on or off-
road). A rubber bed mat is recommended to protect the truck bed and camper, but is not a
requirement to maintain the Torklift legendary lifetime warranty.
Suspension
To significantly reduce body roll, sag and sway Torklift strongly recommends the StableLoad.
Torklift International StableLoads improve safety, handling, and to help level your truck. More
information can be found at (www.Torklift.com/stableload).
If your truck is additionally equipped with suspension air bags Torklift cautions against over
pressurization as this may lead to unsafe vehicle handling characteristics. We have found that
airbags used in conjunction with StableLoads have allowed operators to lower air bag pressure
by 50% or more. Only pressurize suspension air bags enough to level the truck.

3
C2213/C2220 PARTS INVENTORY
2- 1-1/2” X 3/16” X 17-7/8”(45cm) BENT INSERT 6- 1/2” GR5 FLAT WASHER
1- 1/2” BOLT FISHER 2- 1/4” X 1” X 2” PLATE WASHER
2- TIE DOWN FRAME PLATE 2- 1/2” GR5 STAR WASHER
2- SPRING PERCH PLATE 2- 1/2” -13 X 1-1/2” GR5 HEX BOLT
6- 1/2” -13 GR5 HEX NUT 2- 1/2” -13 X 2” GR5 HEX BOLT
6- 1/2” GR5 LOCK WASHER 2- 1/2” -13 X 1-1/2” SQUARE BOLT
2- 1/4'” 2-5/8” INSERT SNAPPER PINPIN
INSTALLATION INSTRUCTIONS:
Locate and inventory all parts to become familiar with all brackets. Read
and understand all instructions. Make sure the vehicle is in park, on a
level surface and wheels are chocked before starting the installation.
STEP 1
Locate the driver’s side rear axle front spring perch. Insert the 1/2” bolt
fisher coiled end through the small hole on the underside of the spring
perch and out the side. Place one 1/2” -13 x 1-1/2” square bolt onto the
bolt fisher and string it through. See photo 1.1 & 1.2 (Bolt fishing guide
on Page 11)
STEP 2
Locate the driver’s side cab and spring mount. Locate the oval hole
between the two mounts and the circular hole just to the front of the cab
mount. Insert the 1/2” bolt fisher’s coiled end first through the oval hole
and out the circular hole. Connect the 1/2” -13 x 2” GR5 hex bolt to the
bolt fisher and string it back through. Once through insert one 1/2” GR5
star washer, and one 1/4” x 1” x 2” plate washer through the open end
of the bolt fisher and place individually through the oval hole and pull
back through. SEE PHOTO 2.1 & 2.2

4
PHOTO 1.1
PHOTO 1.2

5
PHOTO 2.1
PHOTO 2.2
STEP 3

6
Locate the driver’s side front bed cross member perch. Remove the factory bolt
from the perch and bed cross member (keep the factory bolt handy). SEE
PHOTO 3.1
PHOTO 3.1
STEP 4
Locate the driver’s side tie down and insert the bolt fisher end
through the left hole in the tie down. Place the tie down against
the frame and placing the upper support strap on the tie down up
into the bed cross member perch. Replace the factory bed cross
member bolt and hand tighten. Remove the bolt fisher from the
1/2” -13 x 2” GR5 hex bolt and install one 1/2” GR5 flat washer,
one 1/2” GR5 lock washer and one 1/2” -13 GR5 hex nut. SEE
PHOTO 4.1 & 4.2

7
PHOTO 4.1
PHOTO 4.2

8
STEP 5
Locate the supplied spring perch plate and install underneath the
spring perch. Threading the previously installed 1/2” -13 x 1-1/2”
square bolt though the offset hole on the spring perch plate.
Install and hand tighten one 1/2” GR5 flat washer, one 1/2” GR5
lock washer and one 1/2” -13 GR5 hex nut. Line up the second
hole that is centered on the spring perch plate and install one
1/2” -13 x 1-1/2” GR5 hex bolt from the backside of the spring
perch plate and through the tie down. Install and hand tighten
one 1/2” GR5 flat washer, one 1/2” GR5 lock washer and one
1/2” -13 GR5 hex nut. SEE PHOTO 5.1 & 5.2
PHOTO 5.1

9
PHOTO 5.2
STEP 6
Repeat previous steps on passenger side.
STEP 7
Tighten all fasteners to 60 ft-lbs.(81nm) with a torque wrench.
SEE
PHOTO 7.1

10
PHOTO 7.1

11
TORKLIFT’S BOLT FISHING GUIDE
Your guide to understanding the installation of our frame mounted tie downs.
Note: The hardware may vary as to
-Coiled End of Bolt Fisher- what is being fished along with the
bolt. In this instance a 1” X 2” plate
washer is being fished along with
the hex bolt. Different applications
may require fishing through various
star washers and flat washers for
example.
Desired Hole on Vehicle (Place the coiled end of the bolt fisher through this
hole).
This side of the Bolt Fisher should come
out of a hole where the required hardware
(for example 1” X 2” plate washer) can pass through.
This bottom example shows the bolt when it’s completely fished through
the vehicle. You may find it easier to keep the bolt fisher attached until
you get the tie down receiver in place so that the bolt doesn’t fall into the
vehicle frame.
WARNING: PULLING TOO HARD ON THE BOLT FISHER CAN RESULT IN
LOST FASTENERS, OR BROKEN BOLT FISHER.

12
TIEDOWN INSERT INSTALLATION
INSTRUCTIONS
On one end of each of your tie down inserts is a triangular plate referred to
by Torklift as a bullet plate. Your tie down inserts should be installed with the
shorter side of the bullet plate facing away from each other, i.e.. The shorter
side of the front insert should point to the front of the truck and the shorter
side of the rear insert should point towards the rear of the truck.
Once installed, attach the TorkLift directional stickers to the face of the
bullet plate on the insert as a reminder.
DRIVERS SIDE FRONT DRIVERS SIDE REAR
IMPORTANT NOTE: Your tie down inserts are designed to have clearance
inside of the receiver. This is to account for road debris, as well as aid in
installation and removal. Some rattle may be expected if the inserts are left
installed while not under load from the camper.

13
INSTRUCTIONS FOR FINISH MAINTENANCE
OF TORKLIFT PRODUCTS
POWDER COATED STEEL:
To keep your Torklift products looking good follow these guidelines. All steel
powder coated Torklift products are sandblasted for maximum adhesion and use a
high quality industrial urethane based powder coat. Due to the extreme, harsh,
undercar environment that your Torklift products live in, (consistently sprayed with
corrosive road chemicals such as salt, and road debris), Torklift does not warranty
the power coated finish.
To minimize corrosion from these factors on powder coated steel products, Torklift
recommends regularly cleaning and inspecting the powder-coated surface and
touching up any affected areas with enamel or urethane based aerosol paint
product. If there are any areas of surface rust, there are also aerosol spray rust
converters available on the market that can be used as a preparation to touch-up
paint application. These finish maintenance products are available at any
automotive parts supplier.
POLISHED STAINLESS STEEL:
Torklift utilizes quality grade 304 stainless steel in our stainless steel polished
products. 304 stainless steel is well known for its anti-corrosive properties.
However, in some environments such as coastal regions or when coming in contact
with some road chemicals, corrosion may occur.
For a quick clean simply use WD40 and a cloth rag. We also recommend occasional
polishing of our polished stainless products to maintain their attractive finish. Use
an approved stainless steel chrome or aluminum mag wheel polish cleaning product,
which can be purchased from any automotive parts supplier.

14
Torklift International Limited
Lifetime Warranty Information
322 Railroad Ave North, Kent, WA 98032
Torklift will require proof of purchase to register, with pictures of any defective
product before issuing a replacement. Torklift will not register any product without
proof of purchase, which can be faxed, scanned, emailed, or mailed to the
information provided below. Torklift warrants it’s hitches, custom hitch receivers,
frame mounted tie downs, turnbuckles, and accessories (excluding wire
harnesses which carry a 90 day warranty) from date of purchase against defects
in material and workmanship under normal use and service for the ownership life
of the original consumer purchaser. ALL COMMERCIAL APPLICATIONS ARE
WARRANTED FOR A PERIOD OF 90 DAYS FROM THE DATE OF
INSTALLATION/SERVICE. Torklift will replace FREE OF CHARGE any part,
which proves defective in material or workmanship when presented to Torklift,
TRANSPORTATION CHARGES PREPAID by purchaser, at the address above.
THIS WARRANTY IS LIMITED TO DEFECTIVE PARTS REPLACEMENT ONLY.
LABOR CHARGES AND/OR DAMAGE INCURRED IN INSTALLATION OR
REPLACEMENT, AS WELL AS INCIDENTAL AND CONSEQUENTIAL
DAMAGES CONNECTED THEREWITH ARE EXCLUDED. This warranty does
not include the finish or paint on our products. Rusting, cracking or peeling of the
finish is also excluded. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may
not apply to you. Any damage to Torklift products as a result of misuse, abuse,
neglect, accident, improper installation or any use violation of instructions
furnished by Torklift or WHEN USED IN ANY COMMERCIAL APPLICATION
WILL VOID THE WARRANTY. This warranty gives you specific legal rights, and
you may also have rights, which vary from state to state. With warranty service,
you may be able to go to a small claims court, a state court or a federal district
court.

15
322 Railroad Ave North, Kent, WA 98032
Phone [phone] Fax [phone]
or visit our website: www.TorkLift.com
Dear Valued Customer,
Thank you for making TorkLift your choice for truck, camper packages and accessories
for your vehicle. By choosing TorkLift products, you have chosen a company that has
been serving the RV industry for nearly 40 years and whose name has become
synonymous with strength, quality and advanced design and installation.
Please take a few moments of your time to complete the Product Registration
Warranty Card on the next page. When registering your newly purchased TorkLift
products, you can be assured that your contact information is secure and that you and
your product are getting the attention and respect that you deserve.
Thank you again for choosing TorkLift quality products.
Register for your lifetime warranty and receive a free Torklift
International gift.
To Fax: Send copies of the questionnaire, warranty card and receipt to
253-854-8003
To E-mail: Send copies of the questionnaire, warranty card and receipt to [e-mail]
To Mail: Send to Torklift International 322 Railroad Ave North, Kent, WA 98032

16
Frame Mounted Tie Downs
Leading the camper tie down industry in
strength, quality, advanced design and
installation. TorkLift TRUE frame mounted tie
downs are far superior to all tie down
systems available.
The TorkLift system is unique in its design
and is patented. Four independent tie down
points (with no belly or crossbar) working
much like your receiver type trailer hitch as
the inserts are removable allowing the
system to be virtually undetectable when not in use.
They are designed for each make and model to fit tight to the frame so as not to
compromise ground clearance. TorkLift tie downs are not universal ‘one size fits all’
therefore all the problems with correct fit for each particular application have been
eliminated. Original SuperHitch & SuperHitch Magnum
High strength extended hitch system engineered for safely towing all types of
trailers behind your truck and camper. With a max towing capacity of 14,000
lbs.(6350kg) with an extension*, (17,000 lbs.(7711kg) to 20,000 lbs.(9071kg)
without*) the Original SuperHitch and SuperHitch Magnum are rated the
strongest in the industry.
CONTACT YOUR LOCAL DEALER FOR MORE DETAILS
*Weight capacity varies depending on the SuperHitch and SuperTruss extension setup.

17
PLEASE FILL OUT THIS FORM COMPLETELY AND RETURN TO TORKLIFT WITHIN
30 DAYS OF PURCHASE ACCOMPANIED BY A COPY OF YOUR ORIGINAL RECEIPT
1. PART(S) PURCHASED
2. PURCHASER INFORMATION
3. TRUCK INFORMATION
YEAR: ______________ MAKE: _________________
4. CAMPER INFORMATION
YEAR: ___________ MAKE: _______________ MODEL: ________________
5. DEALER INFORMATION
PURCHASED FROM: ______________________________________________
CITY: _________________ STATE: _____ ZIP / POSTAL: ______________
INSTALLED BY: OWNER ABOVE DEALER ANOTHER DEALER
IF ANOTHER DEALER, WHO: _______________________________________
PART#: ___________________ PART#: _______________________
OFFICIAL WARRANTY REGISTRATION CARD
PART#: ___________________ PART#: _______________________
NAME: _____________________________________________________________
EMAIL: ______________________________
ADDRESS: __________________________________________________________
CITY: _________________ STATE: _____ ZIP / POSTAL CODE: ______________
PHONE: ( ) -_________
MODEL:_____________ BED LENGTH: ___________
ADDRESS:______________________________________________________
TODAY’S DATE: _________________________