ReelCraft 7800 OLB21 User manual

1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
SAFETY
INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
7800 OLB21
Operating Instructions
Series 7000 Spring Driven Hose Reels
Clean Air Hose Reel Model Number:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Form# 951-698 Rev: 4/2017
MOUNTING: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or ceiling;
whichever place is convenient. The hose guide arm can be moved to the position desired by removing the nuts fas-
tening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the reel at the desired
position and replace the nuts. A 180° wall mount bracket (600626) or 340° pivot base (600608) are also available
consult manufacturer.
Dimensions
A20 1/4”
B19 3/4”
C7 13/16”
D3 7/8”
E 7”

Series 7000 Spring Driven Hose Reels
Page 2 www.reelcraft.com
Item # Part # # Req. Description Item # Part # # Req. Description Item # Part # # Req. Description
1 261337 1 Adapter Union 9 261370 1 Main shaft** 16 S280-8 1 1/2-20 Hex Nut
2 600375-4B 1 Swivel Assembly** 9 S602683-B 1 Main shaft 17 S260067 1 Latch Spring
2 602691-4B 1 Swivel Assembly 10 300007 2 1¼” Snap Ring 19 S393-2 1 10-32 Shoulder Screw
3 S260011-40 1 Sheave Assembly 11 600016-40 1 Base Assembly 20 S600018 1 Latch Pawl Assembly
4 S260037 1 Drive Spring Assembly 12 S35-84 1 1/2-13 Set Screw 21 S76-106 1 3/8-24 Jam Nut
5 S600621 1 Spring Arbor Assembly 13 600017-40 1 Guide Arm w/rollers 22 S260031 1 Spring Case Stud
6 S260069 1 Gasket 14 300107 4 5/16-18 Lock Nut 23 3-117440 1 U-bolt
7 S260074-40 1 Spring Case Assembly 15 S82-15 7 10-32 x 3/8” Nyloc Nut 24 261650-1 2 1/4-20 x 3/8” Lock Nut
2
34
5
6
715 910
11
12 13
1
14
15
16
17
19
20
21
22
23
24
Maximum operating pressure excluding hose 500 PSI
Maximum operating temperature 210 °F
1. Clean air hose reels do not include filter, regulator, gauge,
hose, valve or respirator.
2. Reel swivel union is 3/4-16 UNF male to fit MSA #455022
hose or equivalent. (1-800-MSA-2222)
WARNING: Only use hose supplied with mask.
Substitution may result in injury or death.
Plant Air
System
Installation Reference Drawing
Hose Reel
(from Reelcraft)
Inlet: 1/2” NPTF (F)
Outlet: 3/4”-16
UNF (M)
Outlet hose, valve, and
respirator assembly (not
included)
Outlet
Inlet
Filter, regulator,
gauge assembly, and inlet
hose (not included)
When changing guide arm positions, the U-bolt must be placed
in the proper location as instructed above. The reel can “latch
out” during use if this instruction is not adhered to.
**Prior to August 2016
See online tech bulletin for more information