Tornador Z-020 User manual

Tornador® is a registered trademark of ECP Inc. ©2021
Tornador® covered by one or more of the following: U.S. Patent Nos. 6,883,732; 8,480,011; 8,690,077; 9,475,071; 10,182,696; 10,189,034; 10,343,177; 10,562,078; 10,730,062;
Taiwanese Patent No. I617360; U.S. Design Pat. Appl. Nos. 29/756,918; 29/756,919; 29/756,920; 29/756,921; 20150000705; 20150375272; Taiwan Application No. 103135808.
SAFETY REQUIREMENTS
• KEEP OUT OF REACH OF CHILDREN.
• The TORNADOR®Black can cause
considerable noise from air pressure.
Please wear hearing protection at all
times.
• When using the TORNADOR®Black,
small pieces of debris can be whirled
into the air. Always wear protective
goggles or glasses to prevent eye
damage.
• The TORNADOR®Black nebulizes
the cleaning liquid. Wear appropriate
respiratory protection to prevent health
hazards from inhalation.
• Use in well ventilated area.
• Do not exceed 90 psi.
• Do not use with acidic, ammable or
combustible products; “USE ONLY
WITH TORNADOR®PRODUCTS.”
• Do not point cleaning tool at face or
body.
• Avoid breathing dust or handling debris
that can be harmful to your health.
• Should you notice a tool malfunction,
discontinue use and contact your
supplier.
• Use caution when other people are in
your surroundings and work area.
• Always disconnect the devise from
the air supply when not in use and
before changing accessories or when
preforming routine maintenance.
• Always check the devise for leaking
hoses, loose ttings or damaged parts.
• We recommend that you never clean
any safety related components with
the TORNADOR®Black tool, i.e., safety
belts, electrical or electronic modules.
AIR REQUIREMENTS
The TORNADOR®Black cleaning tool requires a constant air
pressure between 5.5 and 6.3 bar 78 to 90 psi, for optimum
performance. DO NOT EXCEED 90 psi.
CAUTION: Constant air supply rates vary depending on the size
and power of the compressor. Always make sure tank and air
lines are free from impurities, oil and water contamination.
Page 1 CONTINUED ON BACK PAGE

Tornador® is a registered trademark of ECP Inc. ©2021
Tornador® covered by one or more of the following: U.S. Patent Nos. 6,883,732; 8,480,011; 8,690,077; 9,475,071; 10,182,696; 10,189,034; 10,343,177; 10,562,078; 10,730,062;
Taiwanese Patent No. I617360; U.S. Design Pat. Appl. Nos. 29/756,918; 29/756,919; 29/756,920; 29/756,921; 20150000705; 20150375272; Taiwan Application No. 103135808.
TROUBLESHOOTING
PROBLEM:
• Tip will not oscillate
• Tip moves slowly
• Tip drips uid
• Will not dispense liquid
SOLUTION:
• Check for low air pressure
• Check for dirt build-up and clean
• Keep liquid valve in the horizontal position when not in use
• Check pickup tube for debris and rinse out
LIMITED WARRANTY
“90 day limited manufacturer’s warranty against manufacturing & part defects.” Warranty will be voided, if it is used
for anything other than the intended use of the Tornador®cleaning tool. Use of any products, other the Tornador®
products, with or in the Tornador®cleaning tool, voids warranty.
CARE & MAINTENANCE
1. Avoid dropping the gun on the oor, disconnect when not being used.
2. Turn liquid valve to the horizontal position after use to avoid dripping from tip.
3. Tighten the jar while holding the lid to avoid loosening or stripping gun assembly.
4. Many cleaning solutions will have specic uses. Always use approved cleaning liquids in the TORNADOR®Black
cleaning tool. Using high alkaline or acidic products are not recommended. Always follow manufacturer’s dilution
instructions. Neutral pH products and high volume products work best in the TORNADOR®. Always test in a
small area.
5. When cleaning with the TORNADOR®, use a microber towel to wipe any remaining debris or solution that needs
to be wiped away.
6. Keep the cone of the gun clean by removing the cone and rinsing frequently.
7. Avoid excessive air pressure. Exceeding 90 psi can cause premature wear on the cone and assembly.
NOTE: After every use, place nozzle 2-3 inches into a bucket of soapy water while
depressing the trigger once or twice to quickly remove dirt buildup in the cone. This will
prevent premature wear.
Page 2
INSTRUCTIONS FOR USE
Cleaning Fabric
1. Remove large debris and vacuum area to be cleaned.
2. Turn liquid air valve to upright position to deliver cleaning solution.
3. Hold cleaning nozzle 1 to 3 inches from area to be cleaned. Fully depress trigger.
Begin with overlapping motion over area to be cleaned.
4. Next turn valve to down position using just air and dry the area.
Cleaning Dashboard and Hard Surfaces.
1. Recommended air pressure set at 78 psi
2. Turn liquid valve to straight up vertical position. Using a overlapping motion, spray
area to be cleaned.
3. Allow cleaning liquid to remain on surface for 10 -15 seconds.
4. Follow with air only by turning valve to the horizontal down position. Begin drying
with overlapping motion followed with a soft dry towel.