Toshiba 4400 Series User manual

1
4400 Series UPS Seismic Kit Installation Instructions – 94016-001
4400 Series UPS Seismic Adapter Kit
Installation Instructions
Date: October 2015
Doc. No.: 94016-001
The 4400 Series cabinets can be installed to meet California OSHPD seismic specications using the
optional Seismic Kit and the oor anchorages specied below.
These instructions describe how to install the seismic adapter kits on the 4400 Series UPS, Battery , and
Auxiliary Cabinets. There is a SEISMIC KIT for each cabinet style: 15-30 kVA, 50 kVA, and 80 kVA.
1. 4400 15-30kVA Seismic Installation
2. 4400 50kVA Seismic Installation
3. 4400 80kVA Seismic Installation
1. 4400 15-30kVA Seismic Installation
Table 1 lists the contents of the 4400 15-30kVA Seismic Kit. Figure 1 shows the order of assembly for the
[bolt + lockwasher + washer] fastener group.
TABLE 1 15-30KVA SEISMIC CONTENTS
440300SEISMICKIT Contents
No. P/N* Description Quan
1 93437 TOP SEISMIC BRACKET 30kVA) 1
3 67813 BASE MOUNTING BRACKET, 1
4-a –Hex Bolt, 1/4—20,1-1/2” 1
4-b –Flat Washer, 1/4 1
4-c –E—Ring, F/0.25 Shaft 1
11-a –Hex Bolt, 5/16—18 x 1” 10
11-b –Lock Washer, 5/16 10
11-c –Flat Washer, 5/16 10
–94016 4400 Seismic Kit Installation
Manual
1
a
b
c
FIGURE 1: FASTENER GROUP
(BOLT +LOCK WASHER +
WASHER) Cabinet Footprint
1.75 in
(44.4 mm)
2.75 in
(70 mm)
2.0 in
(51 mm)
Conduit Knock-out
(3 Places)
34.05 in.
(865 mm)
12 in (305 mm) 12 in (305 mm)
9.22 in (234 mm)
4.28 in
(109 mm)
5.55 in
(141 mm)
Base Plate Footprint
1/2 in. Bolt (6)
FIGURE 2: 15-30KVA SEISMIC
ANCHORAGE - FLOOR PATTERN

24400 Series UPS Seismic Kit Installation Instructions – 94016-001
15-30 kVA Seismic Adapter Kit (Cont.)
1. Prepare the oor anchorages. Arrange the anchorages to ac-
commodate the nal layout including placement of ancillary bat-
tery and/or Auxiliary cabinets. (Figure 2)
2. Prepare the wall anchorages. Key measurements off the an-
chorage placement in Step 1. (Figure 3)
3. Table 1 lists the components of the 30kVA Seismic Kit. Figure 4
show the Seismic anchorage components in the Seismic Kit for
the 30kVA cabinets.
4. Assemble the fastener groups in Table 1, [4a-4c], [10a-10c], and
[11a-11c] as shown in Figure 1.
5. Secure the Top Seismic Bracket [1] to the top rear of the UPS
using two (2) fastener group [11]. (Figure 5)
6. Install the Base Brackets, [2], on the UPS base. Use two (2)
fastener group [10] for each bracket. (Figure 6)
7. Secure the Base Mounting Bracket, [3], to the oor anchors
installed in Step 1.
8. Roll the 15-30 kVA UPS cabinet between the two vertical sides of
the Base Mounting Bracket, [4]. (Figure 7)
9. Line up the UPS so the bolt holes on the Bottom Seismic Brack-
ets line up with the holes on the Seismic Base Plate vertical
sides.
10. Secure the UPS to the Seismic Base Plate using the remaining
eight (8) fastener group [11]. Insert the bolts through the Seismic
Bracket to the welded nuts on the Seismic Base Plate. (Figure
7)
11. Secure the Top Seismic Bracket, [1], to the wall anchors installed
in Step 2.
12. Once installation is complete, use the single Fastener Group [4]
to secure the door of the UPS. (Figure 8)
FIGURE 5: TOP SEISMIC BRACKET INSTALLATION
11
11
1
FIGURE 3: 15-30KVA SEISMIC
ANCHORAGE - WALL PATTERN
66.44 in. (1688 mm)
10.05 in
(255 mm)
5 in (127 mm)
1/4” Bolt
Anchor (2)
9.27 in
(471 mm)
Base Mounting Bracket
Cabinet Wall Footprint
P/N 440300SEISMICKIT
1
2
3
4
FIGURE 4: SEISMIC KIT
COMPONENTS (15-30 KVA)

3
4400 Series UPS Seismic Kit Installation Instructions – 94016-001
15-30 kVA Seismic Adapter Kit (Cont.)
10
10 10
10
FIGURE 6: BOTTOM SEISMIC BRACKET INSTALLATION
11
11
11 11
11
11
Slide UPS into
Base Plate
FIGURE 7: INSTALLING ON SEISMIC BASE PLATE
FIGURE 8: SEISMIC DOOR ANCHOR (15-30 KVA)
4

44400 Series UPS Seismic Kit Installation Instructions – 94016-001
FIGURE 9: SEISMIC 15-30 KVA DIMENSAIONAL DRAWING

5
4400 Series UPS Seismic Kit Installation Instructions – 94016-001
2. 4400 50kVA Seismic Installation
Table 2 lists the contents of the 4400 50kVA (4400500SEISMICKIT) and 80kVA (4400800SEISMICKIT)
Seismic Kits. Figure 1 shows the order of assembly for the [bolt + lockwasher + washer] fastener group.
TABLE 2 50 KVA SEISMIC KIT CONTENTS
440500SEISMICKIT Contents
No. P/N* Description Quan
5 66437 TOP SEISMIC BRACKET 1
667193 SEISMIC MOUNTING CHANNEL 2
7-a –Hex Bolt, 1/4—20,1-1/2” 1
7-b –Flat Washer, 1/4 1
7-c –E—Ring, F/0.25 Shaft 1
10-a –Hex Bolt, 1/2—13 x 3/4” 8
10-b –Lock Washer, 1/2 8
10-c –Flat Washer, 1/2 8
11-a –Hex Bolt, 5/16—18 x 1” 4
11-b –Lock Washer, 5/16 4
11-c –Flat Washer, 5/16 4
–94016 4400 Seismic Kit Installation Manual 1
1. Prepare the oor anchorages. Arrange the anchorages to ac-
commodate the nal layout including placement for ancillary
battery and/or Auxiliary cabinets. (Figure 11)
2. Prepare the wall anchorages. Key measurements off the an-
chorage placement in Step 1. (Figure 12)
3. Table 2 lists the components of the 50kVA Seismic Kit. Figure 10
show the Seismic anchorage components in the Seismic Kit for
the 50kVA cabinets.
4. Assemble the fastener groups in Table 2, [7a-7c], [10a-10c], and
[11a-11c] as shown in Figure 1.
5. Secure the Top Seismic Bracket [5] to the top rear of the UPS
using three (3) fastener group [11]. (Figure 13)
6. Position the UPS over the oor anchors
7. Slip each Seismic Mounting Channel [6] over the three oor
anchors on each side of the UPS.
8. Tilt the Base bracket up against the UPS bottom bracket on the
UPS base.
9. Align the holes in the Seismic Mounting Channels [6] with the
UPS bottom brackets.
10. Use the remaining eight (8) fastener group [11] to secure the
Seismic Mounting Channels [6] to the UPS bottom brackets.
(Figure 14, Figure 15)
11. Secure the Top Seismic Bracket to the wall anchors using 5/16” Bolts.
12. Once installation is complete, secure the door of the UPS using the two
(2) Fastener Group [7]. (Figure 16)
a
b
c
FIGURE 1: FASTENER
GROUP (BOLT +LOCK
WASHER + WASHER)
P/N 440500SEISMICKIT
5
6
7
5
FIGURE 10: SEISMIC KIT
COMPONENTS (50 KVA)

64400 Series UPS Seismic Kit Installation Instructions – 94016-001
FIGURE 11: 50KVA SEISMIC
ANCHORAGE - FLOOR PATTERN
28.06 in. (713 mm)
11.5 in. (292 mm) 11.5 in. (292 mm)
4.59 in
(112 mm)
2.03 in
(51 mm)
37.2 in. (944 mm)
32.1 in. (816 mm)
5/8 in. Bolt Anchor (6)
FIGURE 14: BOTTOM SEISMIC BRACKET INSTALLATION
(FLOOR AND ANCHORS NOT SHOWN)
11
11
11
11
11
11
11
11
Bottom
Bracket
P/N 67193
6
6
FIGURE 12: 50KVA SEISMIC
ANCHORAGE - WALL PATTERN
5/16 in. Bolt
Anchor (4)
7.0 in
(178 mm)
75.01 in. (1905 mm)
7.0 in
(178 mm)
10.0 in
(254 mm)
5.0 in
(127 mm)
14.03 in
(356 mm)
Seismic
Mounting
Channel
32.1 in. (816 mm)
4.06 in
(103 mm)
FIGURE 13: TOP SEISMIC BRACKET INSTALLATION
11 11 11
5
Top Bracket
P/N 66437

7
4400 Series UPS Seismic Kit Installation Instructions – 94016-001
FIGURE 16: SEISMIC DOOR
ANCHOR (50-8/0 KVA)
7
7
Anchor Bolt
5/16 in x 18
Press Nut
5/16 in x 18 Bolt
5/16 in Lock Washer
5/16 Washer
11 Fastener Group
FIGURE 15: 50 KVA SEISMIC FLOOR ANCHOR - DETAIL

84400 Series UPS Seismic Kit Installation Instructions – 94016-001
FIGURE 17: SEISMIC 50 KVA DIMENSAIONAL DRAWING

9
4400 Series UPS Seismic Kit Installation Instructions – 94016-001
3. 4400 80kVA Seismic Installation
Table 3 lists the contents of the 4400 80kVA Seismic Kit 4400800SEISMICKIT. Figure 1 shows the order of
assembly for the [bolt + lockwasher + washer] fastener group.
TABLE 3 80 KVA SEISMIC KIT CONTENTS
440800SEISMICKIT Contents
No. P/N* Description Quan
5 66437 TOP SEISMIC BRACKET 1
7-a –Hex Bolt, 1/4—20,1-1/2” 2
7-b –Flat Washer, 1/4 2
7-c –E—Ring, F/0.25 Shaft 2
11-a –Hex Bolt, 5/16—18 x 1” 4
11-b –Lock Washer, 5/16 4
11-c –Flat Washer, 5/16 4
–94016 4400 Seismic Kit Installation Manual 1
80 kVA
1. Prepare the oor anchorages. Arrange the anchorages to ac-
commodate the nal layout including placement for ancillary
battery and/or Auxiliary cabinets. (Figure 19)
2. Prepare the wall anchorages. Key measurements off the an-
chorage placement in Step 1. (Figure 20)
3. Table 3 lists the components of the 80kVA Seismic Kit. Figure 18
show the Seismic anchorage component in the Seismic Kit for
the 80kVA cabinets.
4. Assemble the fastener groups in Table 3, [7a-7c] and
[11a-11c] as shown in Figure 1.
5. Secure the Top Seismic Bracket [5] to the top rear of the UPS
using three (3) fastener group [11]. (Figure 21)
6. Position the 80 kVA cabinet over the four oor anchors and se-
cure the unit.
7. Secure the Top Seismic Bracket to the wall anchors using 5/16”
Bolts.
8. Once installation is complete, secure the door of the cabinet us-
ing the two (2) Fastener Group [7]. (Figure 16)
a
b
c
FIGURE 1: FASTENER
GROUP (BOLT +LOCK
WASHER + WASHER)
P/N 440800SEISMICKIT
80 kVA 5
7
FIGURE 18: SEISMIC KIT
COMPONENTS (50 KVA)

10 4400 Series UPS Seismic Kit Installation Instructions – 94016-001
FIGURE 19: 80KVA SEISMIC
ANCHORAGE - FLOOR PATTERN
27.74 in. (704 mm)
27.1 in. (689 mm)
2.5 in
(64 mm)
2.5 in
(64 mm)
37.2 in. (944 mm)
32.1 in. (816 mm)
5/8 in. Bolt Anchor (4)
FIGURE 20: 80KVA SEISMIC
ANCHORAGE - WALL PATTERN
5/16 in. Bolt
Anchor (4)
7.0 in
(178 mm)
74.98 in. (1904 mm)
7.0 in
(178 mm)
10.0 in
(254 mm)
5.0 in
(127 mm)
13.55 in
(344 mm)
Base
C-Channel
32.1 in. (816 mm)
11 11 11
FIGURE 21: TOP SEISMIC BRACKET INSTALLATION
5