Toshiba TCB-GFC1602UE User manual

–1–
EN
Air Conditioner
INSTALLATION MANUAL
<4-way air discharge cassette type>
Fresh-Air Chamber
MODEL: TCB-GFC1602UE
Thank you for purchasing the “Fresh-Air Chamber” of
TOSHIBA Air Conditioner. Before starting the installation
work, please read this manual carefully and install the
product properly.
PRECAUTIONS FOR SAFETY
• Before installing the product, please read the
“PRECAUTIONS FOR SAFETY” carefully to perform
the proper installation.
• Be sure to keep the instructions described in the
precautionsforsafety,sincethedescriptionsincludethe
important information for safety. The indication and the
meaning of the symbols are as below.
*1: Bodily injury indicates injury, burns, electric shock, and
other injuries which do not require hospitalization or
long-term treatment as an outpatient.
*2: Physical damage indicates the damage relating to the
property, material.
CAUTION ON INSTALLATION
WARNING
Use TOSHIBA products for the parts sold separately.
UsetheproductsspecifiedbyTOSHIBAforthepartssold
separately, such as the ceiling panel, outside air
introduction box. The use of the products other than
specified may cause the water leakage, electric shock,
fire, etc.
CAUTION
Turnofftheearthleakagebreakerwheninstallingthe
outside air chamber.
Be sure to install the outside air chamber to the
indoor unit.
Insufficient installation may cause the water leakage,
electric shock, etc.
1. Specifications
2. Accessories
The following parts are included as accessories in the
product package.
3. Installing the Fresh-Air
Chamber
CAUTION
Handle with care for the product when performing the
ceiling installation. Applying the shock to the side of the
Fresh-Air Chamber may damage the product.
(1) Preparation for installation (Fig. 1)
• Loosen two screws and remove the shield plate
assembly attached to the chamber.
• Remove the panel mounting screws on the indoor unit
and attach them on the chamber. (at four locations)
WARNING This sign denotes that serious
injury may result from improper
use.
CAUTION Thissign denotes thatthe bodily
injury*1or damage*2to property
may result from improper use.
Fresh-air inlet box TCB-GB1602UE
No. Name Shape Q’ty
Mounting screw 4
Mounting screw
(4 screws)
Indoor unit
Mounting
Panelmounting
screws
Fresh-air
chamber
Shield plate assembly
Black
sealing
material
Removal
(Fig. 1)
1-EN
+00CH78994301-1_00Ta.book Page 1 Friday, May 21, 2010 8:22 PM

–2–
EN
(2) Fresh-Air Chamber mounting (Fig. 1)
• Fit the black sealing material side of the Fresh-Air
Chamber to the indoor unit. (It is required to fit each
shape of the indoor unit and Fresh-Air Chamber for the
installation direction.)
• Fix them with the attached Mounting screw (four
screws)
(3) Installing the indoor unit
• Install the indoor unit (with Fresh-Air Chamber) to the
ceiling. (Install the indoor unit following to the
instructions described on the installation manual of the
indoor unit.)
(4) Installing the ceiling panel (sold separately) (Fig. 2)
• Mount the ceiling panel to the Fresh-Air Chamber.
(Mount the ceiling panel following to the instructions
described on the installation manual of the ceiling
panel.)
• Insert the flap motor wiring connector of the ceiling
panel to the hole A for the Fresh-Air Chamber wiring,
and connect to the P.C. board inside the electrical
control box securely. (Fig. 3)
❈Cut the binding band of the flap motor wiring of the
panel and perform the wiring.
• Signalreceivingunitofwirelessremotecontrollerneeds
to be connected to use wireless remote controller (sold
separately). Put wire of the signal receiving unitthrough
hole B and connect it to the terminal block in electrical
control box. (Fig. 4)
(For the details of installation, refer to the manual of
wireless remote controller kit.)
(5) Installing the shield plate assembly
• After closing the electrical control box, mount the shield
plateassemblyby using2screwstotheoriginalposition
whereonceremovedfrom the chamber when preparing
for the installation.
(6) Mounting the fresh-air inlet box
• Mountthefresh-airinletboxfollowingtotheinstructions
described on the manual attached to the product.
4. Confirming the installation
After the installation completes, perform the trial run to
confirm that no abnormality is found.
For your future reference, please keep the installation
manual on your side.
Indoor unit
Electrical
control box Filter hooks
(Fig. 2)
(Fig. 3)
Flap monitor
wiring connector
Hole A for wiring
(Fig. 4)
Hole B for wiring
2-EN
+00CH78994301-1_00Ta.book Page 2 Friday, May 21, 2010 8:22 PM

–20–
TR
CH78994301-1
(2) Fresh-Air Chamber montaj (Resim 1)
• Fresh-Air Chamber ünitesinin siyah sızdırmazlık
malzemesini iç üniteye takın. (Montaj yönü için iç
ünitenin ve Fresh-Air Chamber ünitesinin her biçimine
uyum sağlamak üzere gereklidir.)
•Bunlarıbirlikte verilen Montaj vidası(dört vida) ile takın.
(3) İç ünitenin montajı
•İçüniteyi(Fresh-AirChamberile)tavanamonteedin.(İç
üniteyi, bunun montaj el kitabındaki talimatlar
doğrultusunda monte edin.)
(4) Tavan panelinin (ayrısatılır) montajı(Resim 2)
• Tavan panelini Fresh-Air Chamber ünitesine monte
edin. (Tavan ünitesini, bunun montaj el kitabındaki
talimatlar doğrultusunda monte edin.)
• Tavan panelinin kanat motoru kablo tesisatı
konnektörünü Fresh-Air Chamber kablo tesisatının A
deliğine yerleştirin ve elektronik kartıelektrik kontrol
kutusunun içine sıkıca takın. (Resim 3)
❈Panelin kanat motorunun bağlama bandınıkesin ve
tesisatıdöşeyin.
• Kablosuz uzaktan kumandayı(ayrıolarak satılır)
kullanmak için kablosuz uzaktan kumandanın sinyal
alma ünitesi bağlanmalıdır. Sinyal alma ünitesinin
kablosunu B deliğinden geçirin ve elektrik kontrol
kutusundaki terminal bloğuna bağlayın. (Resim 4)
(Montaj ile ilgili ayrıntılar için, kablosuz uzaktan
kumanda kitinin kılavuzuna bakın.)
(5) Zırh plaka grubunun montajı
• Elektrik kontrol kutusunu kapattıktan sonra, montaja
hazırlık aşamasında çıkarılmışolan 2 vidayıkullanarak
zırh plaka grubunu orijinal konuma monte edin.
(6) Fresh-air inlet box montajı
• Fresh-air inlet box ünitesini ürünle birlikte verilen
talimatlar doğrultusunda monte edin.
4. Montajıonaylama
Montaj tamamlandıktan sonra, herhangi bir anormallik
olmadığından emin olmak üzere bir deneme çalışması
yapın.
İleride başvurabilmek üzere lütfen montaj el kitabını
erişebileceğiniz bir yerde tutun.
İç ünite
Elektrik kontrol
kutusu Filtre kancaları
(Resim 2)
(Resim 3)
Kanat monitörü
tesisat konektörü
Tesisat için A deliği
(Resim 4)
Tesisat için B deliği
2-TR
+00CH78994301-1_00Ta.book Page 20 Friday, May 21, 2010 8:22 PM