Toshiba X100U - TLP XGA LCD Projector User manual

Before UsingPreparationsOperationsMaintenanceOthers
TLP-X100 (XGA)
TLP-WX100 (WXGA)
DATA PROJECTOR
OWNER’S MANUAL
In the spaces provided below, record the Model and Serial No. located at the bottom of
your projector.
Model No. Serial No.
Retain this information for future reference.

2
3
Before Using
SAFETY PRECAUTIONS
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES
ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
WARNING:
USA only
Handling the cord on this product or cords associated with accessories sold with
this product, will expose you to lead, a chemical known to the State of California
to cause birth defects or other reproductive harm. Wash hands after handling.
USA only
Lamp contains mercury. Disposal of this product may be regulated due to
environmental considerations. For disposal, reuse or recycling information,
please contact your local government or the Electronic Industries Alliance at
www.eiae.org.
MODEL NAME: TLP-X100 / TLP-WX100 USA only
TRADE NAME: DATA PROJECTOR MODEL NAME: TLP-X100 / TLP-WX100
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
9740 Irvine Blvd., Irvine, CA 92618-1697 U.S.A
Phone: [phone]
CAUTION:
USA only
Changes or modifications made to this equipment, not expressly approved by
Toshiba, or parties authorized by Toshiba, could void the user’s authority to
operate the equipment.
Notice:
CANADA only
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
Before Using

4
5
Before Using
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE
MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.
This unit is fully transistorized and does not contain any parts that can be repaired by the
user.
WARNING: DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE
EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL ONLY.
1. Read Owner’s Manual
After unpacking this product, read
the owner's manual carefully, and
follow all the operating and other
instructions.
2. Power Sources
This product should be operated
only from the type of power source
which does not exceed the voltage
range specified on the rating label
and the power cord.
If you are not sure of the type
of power supply to your home,
consult your product dealer or local
power company.
3. Source of Light
Do not look into the lens while the
lamp is on. The strong light from
the lamp may cause damage to
your eyesight.
4. Ventilation
Openings in the cabinet are
provided for ventilation and to
ensure reliable operation of the
product and to protect it from
overheating. These openings must
not be blocked or covered. Never
block an opening by placing the
product on a bed, sofa, rug or
other similar surface. Do not place
it in a built-in installation such as
a bookcase or rack, unless proper
ventilation is provided.
5. Heat
The product should be situated
away from heat sources such as
radiators, heat registers, stoves,
or other products (including
amplifiers) that produce heat.
6. Water and Moisture
Do not use this product near water.
- for example, near a bath tub,
wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a
swimming pool and the like.
7. Cleaning
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Always use a soft cloth for
cleaning.
8. Be sure that you firmly
insert the plug into the wall
outlet.
Incorrect or faulty connections
may result in fire or electric shock.
Avoid using an unsound or loose
outlet.
9. Power Cord Protection
Power cords should be routed
so that they are not likely to be
walked on or pinched by items
placed upon or against them,
paying particular attention to cords
at plugs, convenience receptacles,
and the point where they exit from
the product.
10. Overloading
Do not overload wall outlets. To
reduce the risk of electric shock,
do not use the polarized plug with
an extension cord , receptacle, or
other outlet unless the blades can
be inserted completely with three-
wire grounding type to prevent
blade exposure. Failure to follow
these instructions may result in fire
or electric shock.

6
7
Before Using
IMPORTANT SAFETY INSTRUCTIONS (Continued)
11. Lightning storms
For added protection for this
product during a storm, or when it
is left unattended and unused for
long periods of time, unplug it from
the wall outlet. This will prevent
damage to the product due to
lightning and power-line surges.
Never operate this unit on AC
power during a thunderstorm. If
you see lightning or hear thunder,
never touch the unit, cables and/or
peripherals. An electric surge
caused by the storm, may result in
an electrical shock or damage to
the unit.
12. Object and Liquid Entry
Never push objects of any kind into
this product through openings as
they may touch dangerous voltage
points or short-out parts that could
result in a fire or electric shock.
Never spill liquid of any kind on the
product.
13. Do not place or keep the
projector within the reach
of the children.
It may fall or tip over, possibly
causing serious injury.
14. Do not place the product
vertically
Do not use the product in the
upright position or any other
vertical positions to project the
pictures. It may fall which could
result in serious injury and/or
damage to the product.
15. Stack Inhibited
Do not stack other equipment on
this product and do not place this
product on other equipment. The
top and bottom surface of this
product increase in temperature
during normal use and may
damage the other unit.
16. Attachments
Do not use attachments not
recommended by the product
manufacturer.
Use of an incompatible
attachments could cause hazards
or damage to the product.
17. Accessories
Do not place this product on
an unstable cart, stand, tripod,
bracket, or table. The product may
fall, causing serious injury to a
child or adult, and serious damage
to the product. A product and cart
combination should be moved with
care. Quick stops, excessive force,
and uneven surfaces may cause
the product and cart combination
to overturn.
S3125A
18. Damage Requiring Service
Unplug this product from the wall
outlet and take the product to
qualified service personnel if you
encounter any of the following
conditions:
a) The power supply cord or plug is
damaged.
b) Liquid has been spilled, or objects
have fallen into the product.
c) The product has been exposed to
rain or water.
d) The product does not operate
normally when following the
operating instructions. Adjust only
those controls that are covered by
the operating instructions since
an improper adjustment of other
controls may result in damage and
will often require extensive work by
a qualified technician to restore the
product to its normal operation.
e) The product has been dropped or
damaged in any way (If the cabinet
should break, please handle with
care to avoid injury) .
f) The product exhibits a distinct
change in performance, which
indicates a need for service.

8
9
Before Using
IMPORTANT SAFETY INSTRUCTIONS (Continued)
19. If glass components,
including lens and lamp,
should break, contact your
dealer for repair service.
This product incorporates glass
components, including a lens and
a lamp.
If these should break, please
handle with care to avoid injury
and contact your dealer for repair
service. Avoid any broken pieces of
glass since they may cause injury.
In the unlikely event that the lamp
ruptures, thoroughly clean the area
around the projector and discard
any edible items placed in that area
since they may be contaminated.
20. Servicing
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or other
hazards. Refer all servicing to
qualified service personnel.
21. Replacement Parts
When replacement parts are
required, be sure the service
technician has used replacement
parts specified by the manufacturer
or have the same characteristics
as the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
(Only the replacement of the lamp
should be made by users.)
22. Safety Check
Upon completion of any service
or repairs to this product, ask
the service technician to perform
safety checks to verify that the
product is in proper operating
condition.
23. Do not leave thermal-
paper documents or easily
deformed items on top
of the unit or near the air
exhaust for long periods of
time.
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
24. Do not use the product
in a closed installation
location.
Do not place the product in a box
or in any other closed installation
location. Otherwise it may
overheat, which could result in a
risk of fire.
POWER SUPPLY INFORMATION
If your line voltage is 220 to 240 V, use one of the following types of cable/plug.
Plug
configuration Plug type
Australian
240 V
10 A
North American
240 V
15 A
Switzerland
240 V
6 A
Line voltage
EURO
UK
220 – 240 V
220 – 240 V
200 – 240 V
200 – 240 V
200 – 240 V
Plug
configuration Plug type Line voltage
Use a 5 A fuse which is approved by
ASTA or BSI to BSI362.
Always replace the fuse cover after
changing the fuse.
IMPORTANT PRECAUTIONS
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on the
lens and the crucial internal parts. Do not use the unit for at least 2 hours when there is an
extreme or sudden change in temperature to prevent the unit from possible damage.
Place and Manner of Installation
Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening
their lives, and darkening the screen.
Do not use this product in the upright position or tilt it up or down by more than 20° from
level. Doing so may cause a failure or shorten the life of the product.
Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
Moving the projector from a low-temperature room to a high-temperature room may cause
condensation on the lens or internal parts. If you continue to use it in that situation, it may
malfunction. Wait until the condensation naturally disappears.
In a high altitude location where air is thin, cooling efficiency is reduced so use the
projector with [Fan mode] set to [High].
p.41
Only plug the power cord into outlets rated for use with the power cord’s specified voltage range.
Do not overload extension cords or power strips as this can result in fire or electric shock.
Route the power cable or the connecting cable away from where people could trip over it.
The projector may fall down, which could result in severe injury.
Be sure the power cord is easily reached for unplugging in case of emergency. Do not
place any obstacles near a wall outlet in which the cord is plugged.
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time as they will leave marks on the finish.
Do not use a chemically saturated cloth.
•
•
•
•
•
•
•
•
•

10
11
Before Using
IMPORTANT PRECAUTIONS (Continued)
LCD Panel
If the air filter is stained and is clogged up, the main unit inner temperature rises. As a
result, the life of the LCD is shortened and a malfunction may also occur.
Clean the air filter from time to time and replace it regularly. It is recommended that this
replacement be done at the time of replacing a lamp. (Ask a dealer where the unit was
purchased or your nearby service station about an air filter for replacement.)
EXEMPTION CLAUSES
Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, acts
by third parties, other accidents, or use under abnormal conditions including erroneous or
improper operation and other problems.
Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Owner’s Manual.
Toshiba Corporation accepts no liability whatsoever for any damages arising from
malfunctions arising from combination with equipment or software that is not related to
Toshiba Corporation.
OTHER INFORMATION
Copyrights
Showing or transmitting commercial imaging software or broadcast or cable-broad casting
programs with the purpose of other than the personal and private viewing, including
modifying images using the freeze or resize functions, or displaying with the varying
aspect ratio of the images, could violate the direct or indirect copyrights of the imaging
software or broadcast program, etc., if done without first consulting with the copyright
holder. For this reason, please take appropriate measures before performing one of the
actions listed above, including obtaining a license from the copyright holder.
Disposal
This product contains substances which are harmful to humans and the environment.
The lamp contains mercury.
Please dispose of this product or used lamps in accordance with local regulations.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as
household waste. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
•
•
•
•
•
•
OTHER INFORMATION (Continued)
Trademarks
VGA, SVGA, XGA, SXGA, UXGA, WXGA are trademarks or registered trademarks of
International Business Machines Corporation.
Macintosh is a registered trademark of Apple Computer, Inc.
Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.
Adobe and Acrobat Reader are registered trademarks of Adobe Systems Incorporated.
All other brand and product names are trademarks or registered trademarks of their
respective companies.
Notational Conventions Used in This Manual
References to pages with related information are annotated as follows.
For example, if making a reference to page 36:
p.36
The illustrations in this document are for reference purposes only and may not reflect
your package exactly.
REMOTE CONTROL BATTERIES
Warning
Never throw batteries into a fire.
Using the batteries improperly may cause them to explode or leak and may result in serious injury.
If battery-leaking fluid contacts skin, wash the fluid off immediately with clean water and consult
a doctor. If the fluid spills on an instrument, avoid contact and wipe it off using tissue paper.
Then dispose of the used tissue paper as flammable garbage after moistening with water.
Notes
Be sure to use AAA (R03) size batteries.
Dispose of batteries in a designated disposal area.
Attention should be drawn to the environmental aspects of battery disposal.
Do not mix different battery types or combine used batteries with new ones.
If the remote control does not operate correctly, or if the operating range becomes
reduced, replace both batteries with new ones.
If the batteries are dead or if you will not be using the remote control for a long time,
remove the batteries to prevent battery acid from leaking into the battery compartment.
Following information is only for EU-member states:
[Disposal of batteries and/or accumulators]
The crossed out wheeled dust bin symbol indicates that batteries and/or
accumulators must be collected and disposed of separately from household
waste.
If the battery or accumulator contains more than the specified values of lead
(Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive
(2006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or
cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.
By participating in separate collection of batteries, you will help to assure
the proper disposal of products and batteries and thus help to prevent
potential negative consequences for the environment and human health.
For more detailed information about the collection and recycling
programmes available in your country, please contact your local city office
or the shop where you purchased the product.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•

12 13
Before Using
CONTENTS
Before Using
SAFETY PRECAUTIONS ............................................................................. 2
IMPORTANT SAFETY INSTRUCTIONS....................................................... 4
POWER SUPPLY INFORMATION ................................................................ 9
IMPORTANT PRECAUTIONS....................................................................... 9
EXEMPTION CLAUSES ............................................................................. 10
OTHER INFORMATION .............................................................................. 10
REMOTE CONTROL BATTERIES.............................................................. 11
CONTENTS ................................................................................................ 12
Preparations
Checking the package contents .................................................................. 14
Names of each part on the main unit .......................................................... 15
Names of each part on the control panel and remote control ..................... 16
Names of the terminals on the rear panel ................................................... 18
Preparing and using the remote control ...................................................... 19
Placement ................................................................................................... 20
Connection .................................................................................................. 22
Operations
Turning the power on and off....................................................................... 24
Basic operations.......................................................................................... 26
Using handy features .................................................................................. 29
Using auto setting (For computer input only)........................................... 29
Correcting the keystone distortion ........................................................... 29
Resizing image ........................................................................................ 30
Cutting off the picture and sound temporarily (Mute)............................... 31
Changing picture mode............................................................................ 31
Changing screen size .............................................................................. 31
Freezing the image (Freeze).................................................................... 32
Setting the password ............................................................................... 32
Using the menus ......................................................................................... 34
Setup using the Setting display................................................................ 34
The image adjustment menu ................................................................... 35
The display setting menu ......................................................................... 37
The Default setting menu......................................................................... 40
Displaying Information (Status display).................................................... 42
Maintenance
About lamp .................................................................................................. 43
Lamp replacement ...................................................................................... 44
Air filter cleaning.......................................................................................... 47
Lens and main unit cleaning ....................................................................... 48
Others
Trouble indications....................................................................................... 49
Troubleshooting ........................................................................................... 50
Specifications .............................................................................................. 52

14
15
Preparations
Checking the package contents
Preparations
Please make sure that the following items are included in the box, along with the main unit.
If any item is missing, immediately contact the store where you purchased the product.
(1) (4) (7)
(2) (5)
(3) (6)
(1) Remote control
(2) R03 (SIZE AAA) batteries for remote control (2)
(3) CD-ROM
(4)
Owner’s Manual
(5)
RGB cable (3 m) [Note 1]
(6)
Power cord [Note 1, 2]
(7)
Carrying bag
Notes
1: To maintain original performance, always use the supplied cables.
2: The shape and number of supplied power cords vary depending on the product destination.
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection when shipping your projector, repack the set
as it was originally packed at the factory.

The Supplied CD-ROM
The supplied CD-ROM contains an owner’s manual including information not available for
the printed Owner’s manual (Getting started) in Portable Document Format (PDF). Please
use Acrobat Reader 5 or later version to view the manual.
 Adobe®Acrobat®Reader®or Adobe®Reader®
The supplied CD-ROM does not contain Acrobat®Reader®. If you cannot read PDF
files, please install Acrobat Reader software in your computer by downloading it from
the Adobe Systems website.
 Viewing the manual
Run the CD-ROM and double-click on Start.pdf. Acrobat
®
Reader
®
launches, and the menu
screen of the Owner’s manual appears. Click on your language. The Owner’s Manual cover
and list of bookmarks appear. Click on a bookmark title to view that section of the manual.
Click on
p.
to view a reference page with related information. See the Help menu for more
information about Acrobat
®
Reader
®
.
Names of each part on the main unit
( 16 )( 15 ) ( 15 )( 14 ) ( 14 )( 13 )( 10 )( 11 ) ( 12 )
(9)(5)(4) (8)
(7)(6)(1)
(3)
(2)
Back Front
Name : Function
(1) Control panel : Operates the projector.
p.16
(2) Zooming lever : Adjusts screen size.
p.27
(3) Focusing lever : Adjusts screen focus.
p.27
(4) Lamp cover : Remove to replace lamp.
p.44
(5) Air exhaust : Expels air that has grown hot inside the projector.
(6) Air intake : Draws in air from outside the projector for internal cool
down.
(7) Lens cap : Replace the cap when not using the projector to protect
the lens.
(8) Lens : Projects expanded image.
(9) Infrared remote sensor : Senses commands from the remote control.
p.19
( 10 ) AC IN socket : Connects the supplied power cord here.
( 11 ) Terminals on the rear panel :Connects external devices.
p.18
( 12 ) Speaker : Outputs audio sound.
( 13 ) Antitheft lock slot : Attach a safety cable or any other antitheft device.
( 14 ) Foot adjuster release button :Press to set up or stow the foot adjuster.
p.27
( 15 ) Foot adjuster : Adjusts the vertical projection angle.
p.27
( 16 ) Air filter : Prevents dirt and dust from getting into the inside of the
projector.
p.47

16
17
Preparations
Names of each part on the control panel and remote control
Remote ControlControl panel
(1)
(8)
(3) (2)(4)
(6) (5)(7)
(7)
(9)
(8)
(10)
(11)
(12)
(13)
(1)
(2)
(3)
(4)
(6)
(5)
Battery cover
Name : Main Function
Control panel
(1) ENTER button : Accepts the selected mode.
(2) INPUT button : Selects input.
p.26
(3) MENU button : Displays menus.
p.34
(4) RETURN button : Goes back one screen.
(5) ON/STANDBY button/ : Turns the power on/off (standby).
p.25
ON/STANDBY indicator : Displays whether power is on or off (standby).
p.25
(6) TEMP indicator : Lights when internal temperature is too high.
p.49
(7) LAMP indicator : Displays lamp mode.
p.49
(8) Selection button : Menu selections and adjustments, volume control,
Keystone adjustment, etc.
Remote control
(1) ON/STANDBY button : Turns the power on/off (standby).
p.25
(2) FREEZE button : Pauses image.
p.32
(3) MENU button : Displays menus.
p.34
Name : Main Function
(4) ENTER button : Accepts the selected mode.
(5) RESIZE button : Enlarges image.
p.30
(6) SCREEN SIZE button : Changes screen size.
p.31
(7) MUTE button : Cuts off the picture and sound temporarily.
p.31
(8) AUTO SET button :
Performs auto-adjustment of input signals from computer.
p.29
(9) INPUT button : Selects input.
p.26
( 10 )RETURN button : Goes back one screen.
( 11 ) Selection button : Menu selections and adjustments, volume control,
Keystone adjustment, etc.
( 12 ) PICTURE button : Changes image mode.
p.31
( 13 ) Ten-Key button : Use when entering password.
Remote
control
button
Input
items
Remote
control
button
Input items
1
[1]
7
[7]
2
[2]
8
[8]
3
[3]
9
[9]
4
[4]
0
[0]
5
[5] Deletes one character.
6
[6]
Note
For the remainder of this manual, buttons are referred to as follows:
Selection buttons
⇒
; ENTER button
⇒
•

18
19
Preparations
Names of the terminals on the rear panel
(5)
(4)(3)(1) (2)
(8)
(7)(6) (9)
Name : Main Function
(1) AUDIO IN terminal : Input audio signals from a computer or video equipment.
(Multiple use for COMPUTER 1 IN/2 IN, VIDEO and
S-VIDEO)
(2) S-VIDEO terminal : Input S video signals from video equipment.
(3) COMPUTER 1 IN (Y/PB/PR 1) terminal
: Input analog RGB signal from a computer, or a
component video signal (Y/PB/PR) from video equipment.
(4) COMPUTER 2 IN (Y/PB/PR 2) terminal/MONITOR OUT terminal
: Inputs analog RGB signal from a computer
or a component video signal ( Y/PB/PR ) from video
equipment.
It can also be used as MONITOR OUT terminal by the
switch of (5).
(5) Switch : Switches between COMPUTER 2 IN and MONITOR OUT.
(6) AC IN socket : Connects the supplied power cord here.
(7) AUDIO OUT terminal : Outputs audio signals.
(8) VIDEO terminal : Input video signals from video equipment.
(9) CONTROL terminal : When operating the projector via a computer, connect this
to the controlling computer’s RS-232C port.
p.55
Loading dry-cell batteries
into the remote control
1Remove the battery cover.
2Insert the dry-cell batteries.
Be sure to align the plus and minus ends
of the batteries properly.
Two batteries (R03, SIZE AAA) are used.
3Replace the battery cover.
■Operating the remote
control
Point toward the projector’s infrared
remote sensor, and press any button
on the remote control.
Operating the projector from the front
Approx.15°
Approx.5m
When operating the remote control
from behind the projector, the infrared
signal is reflected on the projecting
surface and may travel a shorter
distance to reach the projector
depending on the shape and material
of the projecting surface.
■
•
Dry-cell batteries
Before using the batteries, be sure to observe the Safety Precautions described in
previous pages.
Remove batteries from remote control when not using for extended periods.
If the remote control stops working, or if its range decreases, replace all the batteries
with new ones. (2 batteries (R03, SIZE AAA))
Keep the batteries away from the reach of children.
Batteries are choking hazards and can be very dangerous if swallowed. If the batteries
are swallowed, seek medical assistance immediately.
The remote control
The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
Do not drop or bang.
Do not leave in hot or humid locations.
Do not allow it to get wet or place it on top of wet objects.
Do not take apart.
In rare cases, ambient conditions could impede the operation of the remote control. If
this happens, point the remote control at the main unit again, and repeat the operation.
•
•
•
•
•
•
•
•
•
•
Preparing and using the remote control

20 21
Preparations
Placement Styles
As shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the
Default setting 2 menu
p.41
, in accordance with your needs.
Floor-mounted front projection
Floor-mounted rear projection
Ceiling-mounted front projection
Ceiling-mounted rear projection
WARNING
Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS
when placing the unit. Attempting to clean and replace the lamp in a high location
by yourself may cause you to fall, resulting in injury.
If you wish to mount the projector on the ceiling, be sure to ask your dealer
to do so. Mounting the projector on a ceiling requires special ceiling brackets (sold
separately) and specialized knowledge. Improper mounting could cause the projector
to fall, resulting in an accident.
If the projector is ceiling-mounted, install the breaker for turning off the power in
case of anomaly. Let everyone involved with the use of the projector know that fact.
•
•
•
Placement
a (min length) = Projection size (inches) - 0.795
32.885
a (max length) = Projection size (inches) - 0.673
27.397
Projection
size
Projection distance a
Height (H)
min length
(zooming max)
max length
(zooming min)
30 inches 0.89 m (2.92 ft.) 1.07 m (3.51 ft.) 6.50 cm (0.21 ft.)
40 inches 1.19 m (3.90 ft.) 1.44 m (4.72 ft.) 8.70 cm (0.29 ft.)
50 inches 1.50 m (4.92 ft.) 1.80 m (5.91 ft.) 10.90 cm (0.36 ft.)
60 inches 1.80 m (5.91 ft.) 2.17 m (7.12 ft.) 13.10 cm (0.43 ft.)
70 inches 2.10 m (6.89 ft.) 2.53 m (8.30 ft.) 15.20 cm (0.50 ft.)
80 inches 2.41 m (7.91 ft.) 2.90 m (9.51 ft.) 17.40 cm (0.57 ft.)
90 inches 2.71 m (8.89 ft.) 3.26 m (10.70 ft.) 19.60 cm (0.64 ft.)
100 inches 3.02 m (9.91 ft.) 3.63 m (11.91 ft.) 21.80 cm (0.72 ft.)
120 inches 3.63 m (11.91 ft.) 4.36 m (14.30 ft.) 26.10 cm (0.86 ft.)
150 inches 4.54 m (14.90 ft.) 5.45 m (17.88 ft.) 32.70 cm (1.07 ft.)
200 inches 6.06 m (19.88 ft.) 7.28 m (23.88 ft.) 43.50 cm (1.43 ft.)
250 inches 7.58 m (24.87 ft.) 9.10 m (29.86 ft.) 54.40 cm (1.78 ft.)
300 inches 9.10 m (29.86 ft.) 10.93 m (35.86 ft.) 65.30 cm (2.14 ft.)
90°
As seen from above
As seen from the side
Screen
Lens center
a
90°
Projection Distance and Size
Use the figures, tables, and formulas below to determine the projection size and projection distance.
(Projection sizes are approximate values for full-size picture with no keystone adjustment.)
a (min length) = Projection size (inches) - 0.758
31.022
a (max length) = Projection size (inches) - 0.643
25.845
Projection
size
Projection distance a
min length
(zooming max)
max length
(zooming min)
30 inches 0.94 m (3.08 ft.) 1.14 m (3.74 ft.)
40 inches 1.27 m (4.17 ft.) 1.52 m (4.99 ft.)
50 inches 1.59 m (5.22 ft.) 1.91 m (6.27 ft.)
60 inches 1.91 m (6.27 ft.) 2.30 m (7.55 ft.)
70 inches 2.23 m (7.32 ft.) 2.68 m (8.79 ft.)
80 inches 2.55 m (8.37 ft.) 3.07 m (10.07 ft.)
90 inches 2.88 m (9.45 ft.) 3.46 m (11.35 ft.)
100 inches 3.20 m (10.50 ft.) 3.84 m (12.60 ft.)
120 inches 3.84 m (12.60 ft.) 4.62 m (15.16 ft.)
150 inches 4.81 m (15.78 ft.) 5.78 m (18.96 ft.)
200 inches 6.42 m (21.06 ft.) 7.71 m (25.30 ft.)
250 inches 8.03 m (26.35 ft.) 9.65 m (31.66 ft.)
300 inches 9.65 m (31.66 ft.) 11.58 m (37.99 ft.)
TLP-X100
TLP-WX100
90°
As seen from above
As seen from the side
Screen
Lens center
90°
a
ais the distance (m, feet) between the
lens and the screen, and corresponds
to a range of 0.89 m (2.92 ft.) to 10.93
m (35.86 ft.). His the height from the
image bottom to the center of the lens.
ais the distance (m, feet) between the
lens and the screen, and corresponds
to a range of 0.94 m (3.08 ft.) to11.58 m
(37.99 ft.).
The lens center is in the same level with
an image bottom.

22 23
Preparations
Connection
Before connection
Read the owner’s manual of the device you are connecting to the projector.
Some computers cannot be used with or connected to this projector.
Check for an RGB output terminal, supported signal
p.53
, etc.
Turn off the power of both devices before connecting.
The figure below shows sample connections. This does not mean that all of these devices
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
•
•
•
•
To audio
ouput
Audio cable (not supplied)
Conversion adapter
BNC-pin (not supplied)
To Y/CB/CRoutput
Green(Y)/Blue(CB)/
Red (CR)
RGB cable
(supplied)
Video cable
(not supplied)
Audio cable
(not supplied)
To audio
ouput
White (L)/
Red (R)
To RS-232C
terminal
p.55
Audio cable
(not supplied)
Video recorder,
DVD player, etc. Computer
To
video
output
DVD video recorder, etc.
Audio cable
(not supplied)
Monitor cable Mini
D-sub 15P-BNC
(not supplied)
To audio
output
White (L)/
Red (R) To RGB output
Computer (for control)
To
S-video
output
To audio intput
White (L)/Red ( R)
Audio amplifier, etc. It is necessary to switch
to MONITOR
OUT by the switch.
p.18
S-video cable
(not supplied)
Control
cable (not
supplied)
* The connection for COMPUTER 1 IN terminal described here is also applicable for COMPUTER 2 IN terminal.
Monitor
Notes
When COMPUTER 2 IN terminal is used as MONITOR OUT terminal, the signal which is
input to COMPUTER 1 IN terminal is output.
Signals are output from MONITOR OUT terminal even in standby mode.
However, from AUDIO OUT terminal, no audio signal is output.
A computer monitor cannot accept Y/PB/PRsignals correctly.
The AUDIO IN terminal can be used for devices connected to COMPUTER 1 terminal,
COMPUTER 2 terminal, VIDEO terminal and S-VIDEO terminal.
When an AUDIO OUT terminal is connected, sound is not output from the projector speaker.
Output volume of AUDIO OUT terminal can be adjusted by the VOL button.
•
•
•
•
•
•

24
25
Operations
Connecting the power cord
1
Insert the power cord connector into
the AC IN socket of the projector.
2
Insert the power cord plug into a
wall or other power outlet.
The ON/STANDBY indicator will change to orange,
indicating standby mode.
Turning the power on
1
Removing the lens cap
Be sure to remove the lens cap when the power is turned on. If the cap is left on the
projector, it could become deformed due to heat.
2
Press the ON/STANDBY button.
The power turns on with a beep sound (if the beep
sound is set to [On]), and the ON/STANDBY indicator
flashes green. After a moment, the start-up screen
appears.
CAUTION
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyesight.
Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
Do not place your hands, face, or other objects near the air exhaust, the lamp cover or the
bottom of the unit. Doing so could result in injury and/or damage the object.
•
•
•
Notes
The start-up screen will disappear after a moment. You can configure the system to
prevent the start-up screen from appearing. To do this, use the Display setting menu
p.37
.
The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed
p.26
.
You can disable the beep sound in the Default setting 1 menu
p.40
.
When [Key lock] is [On], the operation buttons of the projector do not work
p.41
.
When [Password] is [On], enter password then the start-up screen is displayed after the
Password entry screen disappears
p.33
.
Do not touch the lens directly with your hand.
If fingerprints or stains are left on the projection lens surface, they may interfere with the
projector’s ability to project images on the screen.
■
■
•
•
•
•
•
•
Turning the power on and off
Operations
Power cord connector
(Supplied)
Control panel
Remote
control
Turning the power off
1
Press the ON/STANDBY button.
When the setting of beep sound is [ On ], the projector beeps, and a message appears
on the screen, confirming that you wish to shut off the power. To shut off the power,
press the ON/STANDBY button again. If you do not wish to shut off the power, wait for a
while without conducting any operations. This message will disappear after a moment.
(This operation is no longer valid after the message disappears.)
2
Press the ON/STANDBY button again.
When the setting of beep sound is [On], the projector
beeps, and the screen disappears, but the internal
cooling fan continues to operate. Then, the projector
goes into standby mode.
During cooling, the ON/STANDBY indicator flashes.
While the indicator is flashing, the power can not be
turned back on. There is no problem with unplugging
the power cord in this state.
3
Replace the lens cap.
After use, replace the lens cap.
Note
The projector consumes about 4.5W of power in standby. We recommend that you
unplug the power cord if you will not be using the projector for an extended period.
Precautions
When you wish to restart the projector again right after turning off the power, give the
lamp time (about 5 minutes) to cool before plugging it back in. If the lamp overheats, it
may fail to light.
Right after turning off the power, the unit may become very hot, especially air exhaust,
lamp cover or the bottom of the unit. Please handle with care to avoid burn injuries.
■
•
•
•
Control panel
Remote
control

26 27
Operations
Notes
When [Auto input search] is set to [Off] in the Default setting 1 menu
p.40
(factory setting is [On]), the Input select menu appears if you press the INPUT
button.
If no signal is being output from the connected equipment, pressing the INPUT button
does not change the input and “There is no other input signal.” message will appear.
5
Projector placement angle adjustments
The placement angle and the height of the projected image can be adjusted by the
foot adjuster.
1Lift up the front of the projector to
the desired angle, then press the foot
adjuster release button upward.
The foot adjuster extends. Release the button
to lock the position.
2To fine adjust the angle, twist the foot
adjuster.
To stow the foot adjuster, hold up the
projector while pressing the foot adjuster
release button, then slowly lower the
projector.
Note
When [Auto keystone] is set to [On] in the Default setting 1 menu, the keystone
distortion will automatically be corrected based on the projector placement angle. If
you do not desire the automatic keystone correction, set [Auto keystone] to [Off].
6
Adjusting the screen size and focus
1Use the zooming lever to adjust the screen size.
2Use the focusing lever to adjust the focus.
7
Adjusting the volume with the buttons
The speaker volume can be adjusted when an audio signal is being input.
•
•
•
•
Basic operations
1
Turn on the power.
Turn on the power by following the instructions in “Turning the power on”
p.24
.
2
Select the language and the lamp power (When using the
first time).
When the projector is used for the first time after purchase, the start menu for language
(to display the menus and messages on the screen) and lamp power selection and
configuration is displayed in English. (If the screen is out of focus, adjust it according to
the step
6
.)
1Use the
, , or button to select the desired language and
press the button.
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
Polish
Norwegian
Finnish
Czech
Hungarian
Greek
Danish
Dutch
Rumanian
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
Indonesian
Thai
Arabic
Message for setup confirmation is displayed in a selected language.
Then, the menu for lamp power selection and configuration is displayed. It is
automatically set as Standard. To change the setting, follow the step 2.
2Use the
or button to select the lamp power and press the
button.
The lamp power, if selected, will be toggled without pressing the button. The display
automatically disappears in a few seconds.
Notes
When the projector is turned on the next time, the start menu does not appear upon
startup. However, if [Reset all] is executed from the Default setting 2 menu
p.41
,
the start menu will be displayed the next time when the power is turned on.
The language can also be set via the Display setting menu
p.37
and Lamp power
via the Default setting 1 menu
p.40
.
This owner’s manual assumes that English has been selected.
3
Activate the connected device.
Turn on and start the connected device such as a computer.
4
Press the INPUT button.
An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.
•
•
•
Front

28
29
Operations
Precautions
Lamp characteristics may rarely cause the brightness to fluctuate slightly.
The LCD panel is made using extremely advanced technology. There may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. These
are intrinsic characteristics of the technology and are not malfunctions.
Notes
A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
Although this projector supports a wide range of RGB signals
p.53
, any resolutions
not supported by this projector (XGA for X100, WXGA for WX100) will be expanded
or shrunk, which will affect image quality slightly. To view high-quality images, set the
computer’s external output to XGA for X100 and WXGA for WX100.
With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the computer’s owner’s manual.
If no signal is being input from the connected equipment or signal input is stopped while
projecting, the “No signal” message will appear.
If a signal not supported by the projector is input, the “Unsupported signal” message
will appear.
If an unavailable operation button is pressed, the icon will appear with a beep sound
(if the beep sound is set to [On]).
Moving pictures played back on computers using DVD software may appear unnatural
when projected with this projector. However, it is not a malfunction of the projector.
•
•
•
•
•
•
•
•
•
Using handy features
Using auto setting (For computer input only)
This function automatically sets up the projector to the optimum state. It
sets up sampling phase, frequency and screen position, for each type
of the input signal by using simple operations.
Press the remote control’s AUTO SET button.
The icon will appear during processing.
You can set as well by selecting [Auto setting] in the Image
adjustment menu
p.35
.
Notes
The image may not be projected or auto adjustment/setting may not be performed
correctly for input signals other than those supported by the projector
p.53
,
p.54
.
If auto setting fails adjustment, adjust manually with [Position]in the Image
adjustment menu
p.35
.
Correcting the keystone distortion
When the projector placement angle against the screen is changed while projecting the
image, the picture will undergo keystone (trapezoidal) distortion.
This projector is capable of correcting this keystone distortion.
Before correction After correction
The keystone distortion will be corrected automatically based on the projector’s
placement angle.
Adjusting Keystone distortion Manually
Use the buttons for keystone adjustment.
Notes
Depending on the amount of keystone adjustment
and the content of images, some information may
be lost, or the picture quality may suffer.
Even if [Auto keystone] is set to [On], keystone
distortion can be adjusted manually. Note that if
you change the position or angle of the projector,
automatic keystone correction will be performed
again.
When [Auto keystone] is set to [On], the automatic keystone correction will be
performed each time the power is turned on.
The keystone correction settings are memorized after the power has been turned off.
Therefore, it is recommended that you set [Auto keystone] to [Off], if the case is that
the projector placement angle against the screen remains unchanged and you do not
wish to change the keystone adjustment that you set.

•
•

•
•
•
•
•
Remote
control
Control panel Remote
control
Basic operations (Continued)
LCD Panels
LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the
following precautions.
• In order to extend the lifetime of the LCD panel, always turn off the power when not in
use, and make sure that the lamp is off. Keeping the lamp off is also very effective at
saving electricity.
• If the air filter becomes dirty and clogged, the projector’s internal temperature will
rise, shortening the lifetime of the LCD panel and causing malfunctions. Clean the air
filter from time to time
p.47
, and replace it periodically. Contact the store where you
purchased your projector, or your local Service Station for replacement air filters.

30
31
Operations
Resizing image
The projected image can be resized (zoomed in/out).
Press the remote control’s RESIZE button.
Each time you press the RESIZE button, zoom ratio is up. You can keep
pressing.
To zoom out, press the remote control’s RESIZE
button.
Each time you press the RESIZE button, zoom ratio is
down.You can keep pressing.
(However, the image cannot be smaller than the original
size.)
To move the area to zoom in, use the
buttons.
You can keep pressing.
When the image returns to the original size by pressing RESIZE
button several times, the zoom will be reset.
Pressing the RETURN button during resizing also resets the zoom.
Notes
The icon appears while resizing.
Operating a function other than Mute will release resizing.
As zooming is processed digitally, the image quality is degraded in larger zoom
ratio.
During resizing or moving the zooming area, the image may be distorted.
■
•
•
•
•
1
3
4
2
Remote
control
Using handy features (Continued)
Cutting off the picture and sound temporarily
(Mute)
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be
turned off.
Press the remote control’s MUTE button.
The picture and sound are cut off. (The Mute function is released
when pressing the MUTE button again.)
Notes
The icon will appear while mute is in effect.
Operating any other functions will also cancel the muting.
Changing picture mode
The projected image mode can be selected.
Press the remote control’s PICTURE button.
Pressing the button switches 1/2/3 in turn.
1: Bright
2: Standard
3: True color
Note
[Picture mode] of the Image adjustment menu has the same
function
p.35
.
Changing screen size
The screen size for the projected image can be changed.
Press the remote control’s SCREEN SIZE button.
Pressing the button switches in turn as follows:
X100 : Normal/Full/Thru/Wide
WX100 : Normal/Full/Thru/4:3 zoom
Notes
Thru display is available for Computer-input images.
Wide or 4:3 zoom display is available for Y/PB/PR, Video and S-video-input images.
[Screen size] of the Display setting menu has the same function
p.37
.
If you use this function on commercial video software, broadcast or cable-
broadcasting except for the purpose of your private viewing and listening, it may
infringe the copyright protected by the copyright laws.
■
•
•
■
•
■
•
•
•
•
Remote
control
Remote
control
Remote
control
1
2
3
4

32
33
Operations
Freezing the image (Freeze)
The projected image can be frozen. This function is to be used to pause
a video during a presentation, etc.
Press the remote control’s FREEZE button.
The picture pauses. (The Freeze function is released by pressing
the FREEZE button again.)
Notes
The icon will appear while freeze is in effect.
Other operations will also release the freeze.
Even if an image is frozen on the projector, the pictures are running
on the video or other equipment.
If you use this function on commercial video software, broadcast
or cable-broadcasting except for the purpose of your private
viewing and listening, it may infringe the copyright protected by the
copyright laws.
Setting the password
How to change password
The default password is 000000.
1
Select [Password] in the Default setting 2 menu and press the or
button.
2
Select [Password registration] in the password registration, setting
menu, and press the button.
The password entry screen is displayed.
3
Enter the current password (6-digit number) using numeric keys of the
remote control.
Enter [000000] (6 zeros) for the first change.
The password is not displayed. Instead it appears as [******].
4
Enter a new password (6-digit number).
5
Re-enter the same password for confirmation.
Note
Please do not forget your password. If you forget the password, you can not
release the password by yourself.
In such a case, please inquire your dealer.
•

•
•
•
•

•
•
Remote
control
How to set password (from [Off] to [On])
1
Select [Password] in the Default setting 2 menu and press the or
button.
2
Select [Password setting] next, and press the or button.
3
Select [On].
4
Select [OK] and press the button.
The password entry screen is displayed.
5
Enter the password using numeric keys of the remote control.
6
The password setting will be set as [On].
How to operate when password is [On]
1
Turn on the power.
2
The lamp lights and the password entry screen appears.
3
Enter the password using numeric keys of the remote control.
If the entered password is correct, the start-up screen appears and the projector
goes into normal operation. If the password is wrong, a message appears to prompt
you to re-enter the password, and again the password entry screen is displayed. If
you enter a wrong password for more than 5 times, the projector will automatically
power off and enter standby mode.
Note
When the password setting is [On], the password function will be enabled only
when the projector is restarted after the power cord has been unplugged.
The password that you set will not be enabled when restarting from standby mode
without unplugging the power cord.
How to set password (from [On] to [Off])
1
Select [Password] in the Default setting 2 menu and press the or
button.
The password entry screen is displayed.
2
Enter the password using numeric keys of the remote control.
3
Select [Password setting] next, and press the or button.
4
Select [OFF].
5
Select [OK] and press the button.
•
Using handy features (Continued)

34 35
Operations
Using the menus
You can call up on-screen menus, and conduct a number of adjustments and settings using
the MENU button
p.16
on the control panel (main unit side) and remote control.
Setup using the Setting display
The menu shown below is for operation instructions purposes and might differ from the
actual display.
These marks
signify that there
are options.
Press or
to display a list of
options.
* When no item is
changed, press .
These marks signify
that there are setting
screens. Press or
to display a list of
setting screens.
Toggle items with .
Select items with and press .
Fix selection with .
Display the Setting display menu.
1. Press the MENU button
2. Select a Category
3. Adjustments & Settings
• The figure shows displays given for operation instructions purposes. As the display may differ depending on the item,
refer to the following applicable pages for the menu item you desire.
• To return to previous item, press the RETURN button.
Item
Adjustment/Setting Value
These marks signify
the items can be
adjusted/set by using
.
These marks signify the items can
be selected from the list by using
.
After an item is selected, apply it by
pressing .
Press or to open the menu.
4. End Press the MENU button once more.
(The menu will disappear automatically after 30 seconds, if no operation is conducted.)
Select a category by using .
There are following 5 categories:
Displays the current
adjustments and
settings of selected
category.
Item shown with gray
cannot be adjusted with
the current input source.
p.35
Image adjustment menu
p.37
Display setting menu
Default setting 1 menu
p.40
Default setting 2 menu
p.41
Status display menu
p.42
■
The image adjustment menu
Use this menu to set or adjust image-related items. Items that can be set or adjusted
are marked “Yes”, and those that cannot are marked “No”. (When an item is masked, it
indicates that you cannot select for the current input.)
Item Description Computer Y/PB/PRVideo S-video
Contrast Adjust the image contrast.
Lower Higher Yes Yes Yes Yes
Brightness Adjust the brightness of the image.
Darker Brighter Yes Yes Yes Yes
Color Adjust the color of the image.
Lighter Deeper No Yes Yes Yes
Sharpness Adjust the sharpness of the image.
Softer Sharper Yes Yes Yes Yes
Noise
reduction
*1
Set the function to reduce screen noise.
On (Enable) Off (Disable)
No Yes Yes Yes
Picture
mode
Press . Toggle the picture mode
with . 1/2/3 Yes Yes Yes Yes
R-level Adjust red of the image color.
Less red More red Yes Yes Yes Yes
G-level Adjust green of the image color.
Less green More green
Yes Yes Yes Yes
B-level
Adjust blue of the image color.
Less blue More blue
Yes Yes Yes Yes
NTSC mode*2 Set the black level with .
US : NTSC (US) mode
JAPAN : NTSC (JAPAN) mode
No No Yes Yes
Auto setting Automatically adjusts items such as
the sampling phase depending on the
type of input signal.
Yes No No No
Position Press then change mode using
and adjust with Yes No No No
Phase
Adjust to eliminate flicker. Yes No No No
Frequency
Adjust to eliminate periodic patterns
and flickering when many fine vertical
lines appear on the screen.
Yes No No No
H-position
Adjust the horizontal position of the
image.
Yes No No No
■

36
37
Operations
Item Description
Computer Y/PB/PRVideo S-video
Position V-position
Adjust the vertical position of the
image.
Yes No No No
Clamp 1
Adjusts the clamp pulse position. Yes No No No
Clamp 2
Adjusts the clamp pulse width. Yes No No No
*1: [Noise reduction] may not work depending on signal type.
*2: [NTSC mode] can be displayed and adjusted only when the video signal is set to [NTSC] or
[NTSC4.43]. NTSC mode is set to JAPAN when the language is set to Japanese. It is set to US for
other languages.
Using the menus (Continued)
The display setting menu
Use this menu to set screen display-related items.
(The items in gray color cannot be set with the current input selection.)
Item Description
Screen size Screen size setting
[ or : Enter setting] [ :Selection] [Enter: ]
X100 : Normal/Full/Thru/Wide
WX100 : Normal/Full/Thru/4:3 zoom
Up/down
shift
Lets the projected images shift vertically when the screen size setting is selected
Wide for X100 (within the range of 1024 x 768) and 4:3 zoom for WX100 (within
the range of 1280 ×800).
Lower the image Raise the image
Blackboard
mode
When projecting on a non-screen surface, select a color in accordance with the
projecting surface.
Press and switch with and . Off/Green/Black/Brown/Blue/Beige
Language Select one of the languages below to use for displaying the menu and messages
[ or : Enter setting] [ :Selection] [Enter: ]
/ / / / / / / /
/ / / / / / / /
/ / / / / / Indonesia /
/
Background Screen to display when there is no input signal
[ or : Enter setting] [ :Selection] [Enter: ]
Logo/Blue/None
Icon Display icons as function guides On Off
Start-up
screen
Display start-up screen when power is turned on On Off
User logo Display a logo customized by the user for the start-up screen or when there is no
input signal.
[ or : Enter setting] [ : Selection]
Logo registration Press to display the registration menu.
Display style
Background Black Blue White
Logo confirmation Press .
Reset logo Yes No
■

38
39
Operations
Detailed description
[Screen size]
Normal•:Enlarge an input image to fit the screen without changing the aspect
ratio of video signals.
Full•:Displays an input image in 1024 × 768 dot resolution by enlarging it to
fill the entire screen. (X100)
Displays an input image in 1280 x 800 dot resolution by enlarging it to
fill the entire screen. (WX100)
Thru•: Displays an input image in the native resolution of the video signals. Thru
display is not available for Y/PB/PR, Video and S-Video-input images.
The larger image than the screen size will be displayed over the
screen. The input image may appear vertically long with some
frequencies of video signals.
Wide
(X100)
•:Displays an input image in the center of the screen with a 16:9 aspect
ratio by enlarging it to fit the width of the screen. The upper and lower
portions of the image will be compressed.
Wide display is not available for Computer-input images.
4:3 zoom
(WX100)
•:Displays an input image with a 4:3 aspect ratio by enlarging it
vertically. The enlarged image will be displayed over the screen. 4:3
zoom display is not available for computer images.
For Y/PB/PRinput, screen size setting function is not available for the video signals
with a 16:9 aspect ratio.
•
Note
If you use the screen size setting function on commercial video software, broadcast
or cable-broadcasting programs to display images with the varying aspect ratio
except for the purpose of your private viewing and listening, it may infringe the
copyright protected by the copyright laws.
[Up/down shift]
Shifts the projected image vertically when [Screen size] is [Wide] for X100.
Shifts the projected image vertically when [Screen size] is [4:3 zoom] for WX100.
[Blackboard mode]
Projects the image in colors more like projecting on a screen.
Precaution
The projected image may differ depending on the type, color, and material of the
blackboard and wall even if the selected color is the same as the projected screens.
[Background]
TOSHIBA is set for [Logo] by factory setting.
If user’s logo has been registered, it is displayed when [Logo] is set for background.
[Start-up screen]
If user’s logo has been registered and this setting is [On], the logo is displayed at start-up.
[User logo]
Registers a part of the image that is input from computer, as a stationary picture and
displays it as a logo at start-up and when no signal is input.
•
•
•
•
Using the menus (Continued)
<Logo registration>
How to register user logo
1
Project a picture to register.
2
Select [User logo] in the Display setting menu, and press the or
button.
3
Select <Logo registration> from the displayed menu list and press
the button.
4
The registration area is displayed for confirmation. Select [OK]
and press the button.
If the registered picture does not fall within the display area, operate the
computer to scroll the screen.
5
Select [Yes] to register and press the button.
6
Registration starts.
A message is displayed while registration is in process.
Notes
You can register a logo when the input is set to Computer.
The area that can be registered is 512 x 384 dots for X100 and 640 x 400 dots for
WX100, at the center of the screen. To register a company logo, prepare the image
within the limit.
Only one logo can be registered. When a new image is registered, the old one is
erased.
The time needed to register or display the image varies depending on the data size.
If you use this function on commercial video software, broadcast or cable-
broadcasting except for the purpose of your private viewing and listening, it may
infringe the copyright protected by the copyright laws.
<Display style>
Select the size of the registered logo.
: Displays the registered image in original size at center of the screen.
: Displays the registered image by enlarging fully in the screen.
(As processed digitally, the image quality is degraded.)
<Background>
Sets background color when [Center] is selected for the logo [Display style].
<Logo confirmation>
You can preview the registered logo.
<Reset logo>
You can reset the registered logo, display style and background to the factory
setting. (The logo set for the start-up screen and background is reset.)
•
•
•
•
•
•
•