Toshiba IK-WF51R User manual

NETWORK CAMERA
Model: IK-WF51R
Quick Start Guide and Important Safeguards
This guide describes the hardware installation.
Refer to the user's manual (PDF le) contained in the CD-ROM for settings, operations
and other information.
The application Adobe® Reader® is needed to view PDF les. If you do not have this
application, download it from the Adobe Systems Incorporated website.
n http://www.adobe.com/
For information on our latest products and peripheral devices, refer to the following
Website:
n http://www.toshibasecurity.com
If the URL changes, refer to the Toshiba website (http://www.toshiba.com).

22
Introduction
FCC (USA)-INFORMATION
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
l Reorient or relocate the receiving antenna.
l Increase the separation between the equipment and receiver.
l Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
l Consult the dealer or an experienced radio/TV technician for help.
USER-INSTALLER CAUTION: Your authority to operate this FCC veried
equipment could be voided if you make changes or modications not expressly approved by
the party.

3
Thank you for purchasing the IK-WF51R Network Camera. Before using the
camera, read this quick start guide carefully to ensure correct usage. After reading
this quick start guide, save it for future reference.
The design, specications, software, and quick start guide contents are subject to
change without prior notice.
Terms
l The term "OS" is used in this manual to indicate operating systems compatible
with this product.
-- Microsoft® Windows® 7 Professional Edition
NOTE
l The performance of the network camera may vary depending on the network
environment.

44
Table of Contents
Introduction 2
FCC (USA)-INFORMATION .......................................................................................2
Terms .........................................................................................................................3
Table of Contents.............................................................................................. 4
Important Safeguards ....................................................................................... 5
Important Safeguards (Cont.) ........................................................................... 7
Notes on Use and Installation........................................................................... 8
Setting the Network Camera Environment ....................................................... 9
Items needed for network camera monitoring ...........................................................9
Contents ......................................................................................................... 10
Physical Description .......................................................................................11
Hardware Installation ..................................................................................... 13
Network Deployment ..................................................................................... 18
Assigning IP Address ...................................................................................... 20
Retrieving Images........................................................................................... 21
Trademarks .................................................................................................... 22

5
Important Safeguards
1. Read Instructions
Read all the safety and operating instructions before operating the product.
2. Retain Instructions
Retain the safety instructions and user's manual for future reference.
3. Warnings
Comply with all warnings on the product and in the user's manual.
4. Follow Instructions
Follow all operating and use instructions.
5. Cleaning
Disconnect this camera from the power supply before cleaning.
6. Attachments
Do not use attachments not recommended by the camera manufacturer as they may pose
safety risks.
7. Accessories
Do not place this camera on an unstable cart, stand, tripod, bracket or table. The camera
may fall, causing serious injury to a person, or serious damage to the product. Use only
with stand, tripod,bracket,or table recommended by the manufacturer, or sold with the
camera. Any mounting of the product should follow the manufacturer's instructions, and
should use a mounting accessory recommended by the manufacturer.
8. Ventilation
This camera should never be placed near or over a radiator or heat register. If this product
is placed in a built-in installation, verify that there is proper ventilation so that the camera
temperature operates within the recommended temperature range.
9. Power Sources
This camera should be operated only from the type of power source indicated on the
information label. If you are not sure of the type of power supply at your location, consult
your product dealer.
10. Power-Cord Protection
Power cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them. Pay particular attention to cords at plugs, screws and
the point where they exit the product.
11. Installation
Install this camera on a secure part of the ceiling or wall. If installed on an unsecured
location, the camera could fall causing injury and damage.

66
12. Lightning
For additional protection on this camera during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the power supply and cable system. This will prevent damage to the camera
due to lightning and power-line surges. If lightning occurs, do not touch the unit or any
connected cables in order to avoid electric shock.
13. Overloading
Do not overload the power supply or extension cords as this can result in a risk of re or
electric shock.
14. Object and Liquid Entry
Never push objects of any kind into this camera through openings as they may touch
dangerous electrical points or short-out parts that could result in a re or electrical shock.
Never intentionally spill liquid of any kind on the camera.
15. Servicing
Do not attempt to service this camera yourself as opening or removing covers may expose
you to dangerous electrical or other hazards. Refer all servicing to qualied service
personnel.
16. Damage Requiring Service
Disconnect this camera from the power supply and refer servicing to qualied service
personnel under the following conditions.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the camera.
c. If the camera has been submerged in water.
d. If the camera does not operate normally by following the operating instructions in the
user's manual. Adjust only those controls that are covered by the user's manual as
an improper adjustment of other controls may result in damage and will often require
extensive work by a qualied technician to restore the camera to its normal operation.
e. If the camera has been dropped or the cabinet has been damaged.
f. When the camera exhibiting a distinct change in performance which indicates a need for
service.
g. Other trouble.
17. Replacement Parts
When replacing parts, be sure the service technician uses parts specied by the
manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in re, electric shock or other hazards.
18. Safety Check
Upon completion of any service or repairs to this camera, ask the service technician to
perform safety checks to determine that the camera is in proper operating condition.

7
Important Safeguards (Cont.)
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning ash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufcient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
FIELD INSTALLATION MARKING:
WORDED: “THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE
PERSON AND SHOULD CONFORM TO ALL LOCAL CODES.”
This product is intended to be supplied by a Listed Power Adapter with LPS, rated PoE 42.5-57Vdc,
0.55-0.41A : 12V DC, 2.1A.
The product is not likely to require connection to an Ethernet network with outside plant routing,
including campus environment; and the installation instructions clearly state that the ITE is to be
connected only to PoE networks without routing to the outside plant.
Ce produit est conçu pour être alimenté par un adaptateur secteur Listed avec LPS, classé PoE
42.5-57Vdc, 0.55-0.41A : 12V DC, 2.1A.
Le produit ne est pas susceptible de nécessiter une connexion à un réseau Ethernet avec
l'extérieur routage des plantes, y compris l'environnement de campus; et les instructions
d'installation clairement que l' état ITE doit être raccordé uniquement aux réseaux PoE sans
routage vers le installations extérieures.

88
Notes on Use and Installation
l Do not aim the camera at the sun
Never aim the camera at the sun even with the camera power off.
l Do not shoot intense light
Intense light such as a spotlight may cause a bloom or smear. A vertical stripe
may appear on the screen. However, this is not a malfunction.
l Treat the camera with care
Dropping or subjecting the camera to intense vibration may cause it to
malfunction.
l Never touch internal parts
Do not touch the internal parts of the camera other than the parts specied.
l Do not submerge in water
The camera has some protection to water (see IP rating), and can be used
indoors or outdoors. If the camera was submerged in water, turn off the power
and contact your dealer.
l Keep the camera installation away from video noise
If cables are wired near electric lighting wires or a TV set, noise may appear in
images. In this event relocate cables or reinstall equipment.
l Check the ambient temperature and humidity
Avoid using the camera where the temperature is hotter or colder than the
specied operating range. Doing so could affect the internal parts or cause the
image quality to deteriorate. Special care is required to use the camera at high
temperature and humidity.
l Should you notice any trouble
If any trouble occurs while you are using the camera, turn off the power and
contact your dealer. If you continue to use the camera when there is something
wrong with it, the trouble may get worse and an unpredictable problem may
occur.

99
Setting the Network Camera Environment
Items needed for network camera monitoring
l Administrator's personal computer
The personal computer that allows setting, operating, monitoring and other
functions with the network camera is called the "administrator's personal
computer" in this guide.
* The personal computer for viewing monitored images is called the "user's
personal computer" in this quick start guide. The network camera can be
viewed by more than one personal computer at the same time.
l Recommended personal computer system requirements:
-- Windows® 7 professional.
-- Internet Explorer® Ver 8.0
-- CPU: Intel® CoreTM i3 or better
-- Memory: 1GB RAM or greater
l Connection equipment such as LAN cables, and switch or router.
-- The LAN cable type differs depending on the connection method.
l Camera search application "Installation Wizard"
-- Install this application from the CD-ROM supplied as an accessory (Double-click
"Setup.exe" in the CD-ROM and install the application by following the onscreen
instructions.)
-- This application is the tool to discover the IP address of a camera. Using this
application, the IP address of a camera can be easily determined.

1010
l IK-WF51R l Power & I/O cable
l Warranty Card l Quick Start Guide and Important
Safeguards
l Gasket / Sillica Gel and tape /
Rubber Washer / Screws and Anchors
l Mounting Plate / Torx driver
Contents
l CD-ROM l Alignment Sticker
NETWORK CAMERA
Model: IK-WF51R
Quick Start Guide and Important Safeguards
This guide describes the hardware installation.
Refer to the user's manual (PDF le) contained in the CD-ROM for settings, operations
and other information.
The application Adobe® Reader® is needed to view PDF les. If you do not have this
application, download it from the Adobe Systems Incorporated website.
n http://www.adobe.com/
For information on our latest products and peripheral devices, refer to the following
Website:
n http://www.toshibasecurity.com
If the URL changes, refer to the Toshiba website (http://www.toshiba.com).
For Mounting Plate For Camera Base

1111
Physical Description
Dome Cover
Cover Screws
IR illuminator Cover
Built-in Microphone
Clear Cover

12
l Inner View
CAMERA MAIN UNIT
Header (J7) Contacts (A)
Lens
Header (J6)
Ethernet 10/100 RJ45 Socket
Align (B) to (A) when
attaching the dome cover
MicroSD/SDHC/SDXC Card Slot
Reset
Button
Status LEDs
Contacts for IR units (B)
NOTE
Gasket for RJ45 LAN
Cable
Stopper for Power &
I/O cable
NOTE
White gasket is for
transportation. Don't use
it in installation.

13
Hardware Installation
S/N: A1510XXXX
MAC: 0002D1XXXXXX
Operating environment
12V DC, PoE+(IEEE802.3at) : -30°C ~ +50 °C (- 22°F ~ 122 °F)
PoE(IEEE802.3af): -10 °C ~ +50 °C (14 °F ~ 122 °F)
l The built-in heater does not work with PoE(IEEE802.3af).
l When the camera is installed and operated in low temperatures below –10 °C {14
°F}, normal images may not be obtained immediately after startup. In such a case,
wait until the camera warms up (taking more than 1 hour) and start adjustment after
turning on the power again.
NOTE
Record the MAC address under the camera base
before installing the camera.
Tamper-proof screws
First, use the supplied torx driver to loosen the four screws and detach the dome cover from the
camera base. Then, follow the steps below to install the camera to either a ceiling or a wall.
Bottom of the camera

141414
RJ45 Cable Dimension (unit: mm)
Assembly Steps
1. Drill a hole on the supplied gasket and
insert a LAN cable through the opening.
2. Strip part of the sheath from the LAN cable.
Recommended cable gauge: (0.51 cm)
Connecting RJ45 Ethernet Cable
Gasket
1
2
3. You will need an RJ45 crimping tool to
attach the Ethernet wires to a connec-
tor. When done, connect the cable to
the camera’s Ethernet RJ45 socket.
o
O
g
B
b
G
br
BR
1
2
3
4
5
6
7
8
3
44. Feed the LAN cable from the bottom of the camera
base and through the hole. Attach the gasket for
water proong.
o: white/orange stripe
O: orange solid
g: white/green stripe
B: blue solid
b: white/blue stripe
G: green solid
br: white/brown stripe
BR: brown solid
NOTE
l RJ45 crimping tool and plug are not included.
l Use Category (Cat) 5e or higher cable.

1515
Connecting Power & I/O Cable
1. Add the supplied rubber washer to the
cable as shown in the picture.
2. Remove the stopper, and feed the cable
from the bottom of the camera base and
tighten the plastic base for waterproong.
3. Connect the white header connectors to
J6 and J7 on the camera.
1
2
3
Connect the supplied power & IO cables if
your switch does not support PoE.
Header (J7)
Header (J6)
NOTE

161616
If you have external devices such as sensors and alarms, make the connection from the general
I/O terminal block.
Power and I/O cable terminal
+3V3
DO
D1
GND
General I/O Terminal Block
Power Cord Socket (Black)
Microphone In (Pink)
Audio Out (Green)
+3V3: Power, 3.3V DC
DO: Digital Output
D I: Digital Input
GND: Ground

171717
Ceiling/Wall Mount without Mounting Plate
(Choose this mounting type if you want to feed the cables from the bottom of
the camera)
12
3
7
8
5
1. Attach the supplied alignment sticker for camera main unit to the ceiling/wall.
2. Using the three circles on the sticker, drill three pilot holes (Ø1/4inch x 1.57inch(D)
(Ø6.35mm x 40mm(D))) into the ceiling. Then hammer the three supplied plastic anchors into
the holes.
3. Drill a cable hole (Ø0.8inch(Ø20mm)) on the ceiling/wall, and feed the cables through the
hole.
4. Connect the LAN cable to the socket (Refer to the page 14.).
5. Secure the camera main unit to the ceiling/wall with three supplied screws.
6. You will nd a silica gel bag attached to the camera. Replace the silica gel bag included in
the camera with the one shipped within the accessory.
7. Attach the dome cover.
8. Secure the four screws with the supplied torx driver. Make sure all camera parts are securely
installed.
l The included screws and anchors are used to
install the camera to a solid surface. (e.g. concrete)
If installing on loose or thin material surfaces , use
the appropriate anchors (not included) with the
screws.
l Arrange the cables neatly to avoid getting in
the way when the dome cover is attached.
NOTE
6

18
Ceiling/Wall Mount with Mounting Plate
(Choose this mounting type if you would like to feed the cables from the side)
1
2
3
4
6
8
1. Attach the supplied alignment sticker for the supplied mounting plate to the ceiling/wall.
2. Using the three circles on the sticker, drill three pilot holes (Ø1/4inch x 1.57inch(D)
(Ø6.35mm x 40mm(D))) into the ceiling. Then hammer the three supplied plastic anchors into
the holes.
3. Arrange and feed the cables through the side of the mounting plate.
4. Secure the mounting plate to the ceiling/wall with three supplied screws.
5. Connect the LAN cable to the socket (Refer to the page 14.).
6. Attach the camera main unit to the mounting plate and turn counter-clockwise as shown below.
Then secure three screws on the mounting plate and the supplied screw to x the camera main
unit to the mounting plate..
7. You will nd a silica gel bag attached to the camera. Replace the silica gel bag with the one
shipped within the accessory.
8. Attach the dome cover.
9. Secure the four screws with the supplied torx driver. Make sure all camera parts are securely
installed.
9
7
6

19
You may also use the diagonal holes on the mounting plate,
marked as A, B, or C, to install the camera to a U.S.standard 4
in. junction box. And secure the camera with supplied screws.
CAUTION
l Installation should be done only by qualied personnel and conform to all local codes.
l Install this camera on a rm and solid part of the ceiling or wall.
If installed improperly or on a weak surface, the camera could fall causing injury and
damage.
The supplied torx driver is exclusively designed to match the dome screws. Do not
discard the torx driver.
Treat silica gel bag with care. Do not tear the silica gel packge.
WARNING:
Keep the silica gel out of the reach of babies, infants, and children.
DO NOT EAT, HARMFUL IF SWALLOWED

2020
Network Deployment
l When using a PoE-enabled switch
The camera is PoE-compliant, allowing transmission of power and data via single LAN
cable. See the following illustration to connect the camera to a PoE switch via LAN
cable.
POWER COLLISION
LINK
RECEIVE
PAR
TITION
12345
POWER COLLISION
LINK
RECEIVE
PAR
TITION
12345
Power over Ethernet (PoE)
PoE (IEEE802.3af, IEEE802.3at)
switch (not supplied)
POWER COLLISION
LINK
RECEIVE
P
AR
TITION
12345
POWER COLLISION
LINK
RECEIVE
P
AR
TITION
12345
l When using a non-PoE switch
Use a PoE power injector (not supplied) to connect between the camera and a non-PoE
switch.
non-PoE switch
(not supplied)
PoE (IEEE802.3af, IEEE802.3at)
power injector (not supplied)
Client PC
(not supplied)
Client PC
(not supplied)
For PoE input, use only UL listed I.T.E. with PoE output.
For PoE input, use only UL listed
I.T.E. with PoE output.